Page 1 HP NetServer E 200 Installation Guide HP Part Number 5969-5988 Printed in March 2000...
Page 2: Audience Assumptions
Hewlett-Packard assumes no responsibility for the use or reliability of its software on equipment that is not furnished by Hewlett-Packard.
Page 3: Table Of Contents
Contents 1 Setting Up the HP NetServer ............... 1 Setup Steps....................1 Preparations....................1 Installation Options ..................2 Installing the HP NetServer................ 4 2 Controls, Ports, and Indicators..............5 Introduction ....................5 Front Panel....................5 Additional Front Panel Controls and Indicators........... 6 Rear View....................
Page 4 Contents 5 Installing Additional Memory ..............29 Introduction ....................29 Tools Required ..................29 Memory Installation Guidelines ..............29 Installing Additional DIMMs................30 Removing DIMMs ..................33 6 Installing Additional Boards ..............35 Introduction ....................35 Tested PCI Boards .................. 35 Tools Required ..................
Page 5 Contents Configure/View Host Adapter Setting ............58 SCSI Disk Utilities..................58 9 Troubleshooting ..................59 Introduction ....................59 Common Installation Problems ..............59 NetServer Will Not Power On..............60 Troubleshooting Sequence ..............60 Error Messages ................... 61 No Error Messages Displayed ..............61 Power-On Self Test (POST) Error Messages ...........
Page 6 Contents Battery Safety Statements ............... 90 Noise and Ergonomic Safety Statements ..........91 C Service and Support.................. 93 D Warranty and Software License..............95 Warranty ..................... 95 HP Software Product License Agreement ............ 95 Non-Nuclear Usage ..................96 Index....................... 97...
Page 7: Setting Up The Hp Netserver
1 Setting Up the HP NetServer Setup Steps The following topics and diagrams provide the most efficient way to set up the HP NetServer E 200. It is important to follow the setup steps in the exact order shown below. Skip any steps that do not apply to you. To provide further details, these steps include references to other sections of this manual and to other documents.
Page 8: Installation Options
Chapter 1 Setting Up the HP NetServer Installation Options WARNING Before removing the cover, always disconnect the power cord and unplug telephone cables. Disconnect the power cord to avoid exposure to high energy levels that may cause burns when parts are short-circuited by metal objects such as tools or jewelry.
Page 9 Chapter 1 Setting Up the HP NetServer Add Memory Use only HP supported DIMMs. Supported DIMMs may be installed in any combination, in any slot. For details refer to Chapter 5, "Installing Additional Memory." Add PCI Boards The slot assignments of additional disk drive controller boards may affect boot order.
Page 10: Installing The Hp Netserver
Chapter 1 Setting Up the HP NetServer Installing the HP NetServer 1) Read the ReadFirst View the ReadFirst sheet from the HP NetServer E Sheet 200 Installation Kit. The ReadFirst Sheet is a quick reference guide to help you install your HP NetServer.
Page 11: Controls, Ports, And Indicators
2 Controls, Ports, and Indicators Introduction This chapter describes the controls, ports, and indicators on the front and rear of the HP NetServer E 200. Before installation, familiarize yourself with the HP NetServer’s controls and indicators. Figures 2-1 and 2-3 show the front and rear of the NetServer respectively.
Page 12: Additional Front Panel Controls And Indicators
Chapter 2 Controls, Ports, and Indicators Table 2-1 provides the front panel power switch and the associated indicator definitions. Table 2-1. Front Panel Switch and Indicators Control / Indicator Description This button turns the HP NetServer power On or Off, and Power On/Off/Sleep Switch if available, also transitions the NetServer between Power...
Page 13 Chapter 2 Controls, Ports, and Indicators Flexible Disk Drive Activity Eject Button CD-ROM Eject Activity Button Eject Button Status DAT Tape LEDs Drive (Optional) Figure 2-2. Input and Storage Device Controls and Indicators Table 2-2. Backup Tape Drive LED Codes Left LED Right LED Definition...
Page 14: Rear View
NOTE For more information on a HP Backup Tape Drive and its error codes, refer to the documentation provided with the tape drive or refer to Hewlett-Packard’s web site at: http://www.hp.com Refer to Chapter 4, "Installing Mass Storage Devices," for installation information.
Page 15: Applying Power To The Hp Netserver
Chapter 2 Controls, Ports, and Indicators Power Strain Relief Keyboard Key Lock Mouse Not Used Serial Port A Parallel Port Serial Port B Video External SCSI SVGA Port Figure 2-3. Rear Panel and Ports Applying Power to the HP NetServer Powering-Up the HP NetServer The HP NetServer E 200 powers up and loads the operating system when you press the power button on the front panel.
Page 16: Powering-Down The Hp Netserver
Chapter 2 Controls, Ports, and Indicators Powering-Down the HP NetServer 1. Log off all users and if necessary, back-up files. Schedule the power down for a time when the fewest users will be affected by the NetServer’s downtime. If you will be doing any kind of hardware or software upgrade, be sure your NetServer’s data has been backed up.
Page 17: Sleep States (Acpi)
Chapter 2 Controls, Ports, and Indicators Sleep States (ACPI) The HP NetServer supports the ACPI (Advanced Configuration and Power Interface) standard, which is a key component of a NOS’s directed power management. The supported features are only available when an ACPI-compliant NOS is installed on the NetServer.
Page 18 Chapter 2 Controls, Ports, and Indicators management is under the control of the ACPI-compliant NOS, the HP NetServer’s power button is capable of an override in case of a non-responsive NOS. NOTE The HP NetServer power button will force a power down without waiting for the NOS to gracefully shut down the NetServer if the power button is pressed and held in excess of four seconds.
Page 19: Opening And Closing The Hp Netserver
3 Opening and Closing the HP NetServer Introduction This chapter describes how to remove and replace the HP NetServer’s main cover and adjust the stabilizing feet on the bottom of the chassis. WARNING Before removing the cover, always disconnect the power cord and unplug telephone cables.
Page 20 Chapter 3 Opening and Closing the HP NetServer Key Lock Screws (3) Figure 3-1. Screws and Lock Holding on Cover 4. Remove the NetServer cover. a. Place your hands near the bottom front of the cover, one along each side. b.
Page 21: Replacing The Cover
Chapter 3 Opening and Closing the HP NetServer Figure 3-2. Removing the Cover Replacing the Cover To replace the cover, follow these steps: 1. If necessary, return the air duct to its closed position. 2. Place one hand on either side of the cover and press inward lightly while lowering the cover onto the chassis.
Page 22 Chapter 3 Opening and Closing the HP NetServer Front of Chassis Bottom of Chassis Figure 3-3. Replacing the Cover 3. Push the cover forward until it is seated in place. 4. Replace the six (6) Torx T-15/slotted screws in the rear. See Figure 3-1. 5.
Page 23: Adjusting The Hp Netserver Feet
Chapter 3 Opening and Closing the HP NetServer Adjusting the HP NetServer Feet The stabilizing feet are used to steady the HP NetServer during normal operation and must be turned outward during the installation process. When adding internal accessories to the NetServer, turn the feet inward so the NetServer will lay flat on its side on the floor or a table.
Page 25: Installing Mass Storage Devices
4 Installing Mass Storage Devices Introduction This chapter describes how to install the internal mass storage devices, including the internal hard disk drives (IDE or SCSI) and the optional Tape Backup (DAT) Drive. The requirements for external SCSI drives are provided in the respective topic later in this chapter.
Page 26: Ide Mass Storage Devices
Chapter 4 Installing Mass Storage Devices SCSI Model Boot Order: 1. IDE CD-ROM Drive Flexible Disk Drive 3. IDE Hard drive (if boot drive) 4. SCSI A Channel (provided by SCSI Controller board) 5. PCI slot 1 6. PCI slot 2 7.
Page 27: Ide Mass Storage Additions
Chapter 4 Installing Mass Storage Devices IDE Mass Storage Additions Table 4-1 lists the number and types of mass storage devices that may be added to the IDE model of the HP NetServer. Table 4-1. IDE Mass Storage Device Types Interface Max Number of Types...
Page 28: Scsi Mass Storage Additions
Chapter 4 Installing Mass Storage Devices CAUTION You must not connect high voltage differential (HVD) SCSI devices on the SCSI bus or you will damage the other LVD SCSI devices. The single channel Ultra Wide PCI SCSI controller board provided with the NetServer SCSI model includes three SCSI connectors and is normally installed on PCI slot 1.
Page 29 Chapter 4 Installing Mass Storage Devices Max Number of Interface Devices Types Possible Installed Devices and Addresses IDE-2 Two additional IDE hard drives in the removable mass storage cage (shelves 4, 5, 6, and 7) are limited by the number of SCSI drives installed. The removable mass storage cage is limited to 4 drives.
Page 30: Installing Hard Disk Drives
Chapter 4 Installing Mass Storage Devices Installing Hard Disk Drives The installation of the hard disk drives is the same for both IDE or SCSI drives. The IDE drives require setting jumpers on the drives for the master and slave drive selection before installing the drives.
Page 31 Chapter 4 Installing Mass Storage Devices 7. Unplug the power and SCSI or IDE cables to any hard disk drives already in the cage. CAUTION Install and remove connectors carefully and avoid displacing any pins. Top of HP NetServer Front of HP NetServer Hard Disk Drive Cage...
Page 32 Chapter 4 Installing Mass Storage Devices 9. Slide the drive into the cage opening with the cable connectors toward the rear of the NetServer. See Figure 4-3. Align the screw holes on the drive (or the shelf or brackets) with the screw holes in the hard disk drive cage.
Page 33 Chapter 4 Installing Mass Storage Devices HDD 1 HDD 2 Tabs HDD 3 HDD 4 Figure 4-4. Hard Disk Drive Cage Screw Holes NOTE Ensure you set up the IDE drive jumpers for master/slave operation before re-inserting the hard drive cage back into the NetServer.
Page 34: External Scsi Connector
Chapter 4 Installing Mass Storage Devices The power cable is split into two cables, each with three power connectors. The designed distribution is: One string of three: CD-ROM, hard drive or optional tape drive, top hard disk drive in mass storage cage. Second string of three: lower three hard disk drives in mass storage cage.
Page 35: Installing Additional Memory
5 Installing Additional Memory Introduction This chapter provides the instructions for installing and removing DIMMs on the system board in the HP NetServer E 200. The video memory is provided on the AGP adapter board and comes with 4 MB standard and cannot be upgraded. NOTE The EDO DIMMs and PC 100 SDRAM DIMMs from earlier HP NetServer models will fit into the DIMM slots in the HP...
Page 36: Installing Additional Dimms
Chapter 5 Installing Additional Memory Use only HP DIMMs, which are available in the following DIMM sizes: 64, 128, and 256 MB. DIMM sizes may be mixed on the system board. DIMMs may be installed in any combination in any slot. However, HP recommends starting at slot 0 (or A) and filling the slots in sequential order: 0 (or A), 1 (or B), etc.
Page 37 Chapter 5 Installing Additional Memory 5. Unsnap the air duct and move it out of the way. See Figure 4-1. 6. Locate the DIMM slots on the system board. See Figure 5-1. DIMM Slots Figure 5-1. DIMM Locations on System Board...
Page 38 Chapter 5 Installing Additional Memory 7. Install the DIMMs in the desired slot. See Figures 5-2 and 5-3: a. Choose a DIMM slot for the desired DIMM. DIMMs may be installed in any combination, in any slot. b. Spread the two retaining latches on the slot outward. CAUTION Use only HP DIMMs, which are 3.3V, 133 MHz (PC133), and registered SDRAM DIMMs.
Page 39: Removing Dimms
Chapter 5 Installing Additional Memory f. If the latches do not close, the DIMM is not inserted correctly. NOTE If the DIMMs are not seated properly, you may get a blank screen when the NetServer boots. 8. Repeat all of Step 7 to install the additional DIMMs for your memory configuration.
Page 40 Chapter 5 Installing Additional Memory Figure 5-3. Removing the DIMM 6. Place the DIMM in its anti-static container. 7. Repeat steps 4-6 for as many DIMMs as you need to remove.
Page 41: Installing Additional Boards
Electrical code (NFPA 70) Class 2 or limited power source limits and must use appropriate interconnecting cabling in accordance with the National Electrical Code. (All Hewlett-Packard boards comply with Class 2.) NOTE The HP NetServer E 200 does not support HP NetRAID boards or Disk Array Controller (DAC) boards.
Page 42: Accessory Board Installation Guidelines
Chapter 6 Installing Additional Boards Accessory Board Installation Guidelines For every accessory board you install, the NetServer needs to set aside available resources to support it. An accessory board typically requires resources such as an IRQ (Interrupt Request) and port address. The PCI boards use the Plug-and-Play feature to correctly assign the IRQ resources automatically.
Page 43: Interrupt Sharing
Chapter 6 Installing Additional Boards 5. PCI slot 1 6. PCI slot 2 7. PCI slot 3 8. PCI slot 4 9. ISA slot The NetServer scans for a boot device on SCSI Channel A starting at device ID 0 and works up through the ID numbers (0-15).
Page 44: Installing Accessory Boards
Chapter 6 Installing Additional Boards NOTE The AGP Video board shipped with the HP NetServer has the interrupt jumper on the board disabled. HP recommends leaving this jumper in the disabled position, unless you are using intensive video operations such as 3D rendering, which can be improved by enabling this jumper on the AGP board.
Page 45 Chapter 6 Installing Additional Boards PCI slot 1 PCI slot 2 PCI slot 3 PCI slot 4 Figure 6-1. Accessory Slots 7. Use the T-15 driver or flat blade screwdriver to remove the PCI slot cover for each slot to be used, and store it for future use. See Figure 6-2. Figure 6-2.
Page 46: Removing Accessory Boards
Chapter 6 Installing Additional Boards 8. Slide the accessory board into the slot. See Figure 6-3. Figure 6-3. Inserting an Accessory Board 9. Secure the accessory board using the screw you previously removed with the slot cover. Use the T-15 driver or flat blade screwdriver. 10.
Page 47: Connecting The Monitor, Keyboard, Mouse, And Ups
7 Connecting the Monitor, Keyboard, Mouse, and UPS Use this chapter to connect the monitor, keyboard, and mouse cables and the AC power cord to the appropriate connectors on the rear of the chassis. When connecting the HP NetServer to peripherals, use the cable ties and labels provided with the product.
Page 48 Chapter 7 Connecting the Monitor, Keyboard, Mouse, and UPS 2. Connect the mouse, keyboard, and monitor to the HP NetServer. 3. Connect the power cord to the rear of the NetServer. 4. Use the power cord strain relief clamp to secure the power cord. 5.
Page 49: Configuring The Hp Netserver
8 Configuring the HP NetServer Introduction This chapter provides the setup instructions for your HP NetServer E 200. The first few topics in this chapter provide an overview of the HP Startup CD-ROM. The balance of this chapter provides the necessary instructions for setting up the (BIOS) Setup Utility and the optional SCSI Select Utility used to configure the HP NetServer E 200.
Page 50: Hp Startup Cd-Rom
Chapter 8 Configuring the HP NetServer HP Startup CD-ROM The HP Startup CD-ROM provides you with the latest NOS drivers, DiagTools Utility, BIOS Flash utility, and a diskette creation Utility. l Run the HP Startup CD-ROM on the HP NetServer to obtain the required NOS drivers and the DiagTools Utility located on the CD-ROM.
Page 51: Setup (Bios) Utility
Chapter 8 Configuring the HP NetServer Setup (BIOS) Utility The HP NetServer has a Setup Utility (BIOS) in read-only memory used to control the NetServer’s BIOS settings stored in the CMOS section of the EEPROM on the system board. The utility features several system configuration and housekeeping options, including security.
Page 52: Using The Setup Screens
Chapter 8 Configuring the HP NetServer recommends using the default settings unless otherwise noted as a factory setting. Refer to Table 8-2 later in this chapter for the factory settings. CAUTION Damage caused to the HP NetServer by non-factory settings may not be covered under the HP warranty.
Page 53 Chapter 8 Configuring the HP NetServer Use the <Esc> key to exit any menu. If you press <Esc> on a submenu, the previous screen appears. When you are making selections from a submenu, use the <Esc> key to close the submenu without making a selection. Use the scroll bar to the right of the help window to view more information than can be displayed on screen.
Page 54: Changing System Date And Time
Chapter 8 Configuring the HP NetServer Changing System Date and Time Use this topic to change the HP NetServer’s date and time and refer to the following procedure. 1. To reach the Setup Utility, boot or reboot the NetServer and press the <Del>...
Page 55: Setting The Hp Netserver's Passwords
Chapter 8 Configuring the HP NetServer 12. Choose Yes and then press Enter. The HP NetServer will reboot. Setting the HP NetServer’s Passwords Use this topic to set passwords to access the BIOS Setup Utility. The password is not used to boot the NetServer, but is required to access the Setup Utility. The Utility provides two separate passwords;...
Page 56: Changing Internal Device Boot Priority
Chapter 8 Configuring the HP NetServer 9. Press <Enter> without typing anything in the dialog box, which will clear the existing password. The (Supervisor or User) Password in the Main menu will change to [Disabled]. If both Supervisor and User passwords are [Disabled] anyone can access all the Setup Utility’s functions.
Page 57 Chapter 8 Configuring the HP NetServer 2. Flexible Disk Drive 3. IDE Hard drive (if the boot drive) 4. SCSI A Channel (provided by SCSI Controller board) 5. PCI slot 1 6. PCI slot 2 7. PCI slot 3 8. PCI slot 4 9.
Page 58: Clearing Cmos
Chapter 8 Configuring the HP NetServer 1. [HP 8.4GB A] 2. [HP 8.4GB A] 4. Use the plus (+) or minus (-) keys to move the desired hard drive to the top of the HD boot list. The IDE HD boot list has a maximum capacity of four (4) hard drives, but the number of IDE hard drives is limited by the other IDE devices used in the NetServer.
Page 59 Chapter 8 Configuring the HP NetServer 8. Exit and save changes, which reboots the NetServer. 9. Replace the cover and return the NetServer to normal operation. Refer to Chapter 3, "Opening and Closing the HP NetServer." CMOS Clear Jumper (CMOSCL) Figure 8-1.
Page 60: Configuring Isa Non-Plug-And-Play Boards (Optional)
Chapter 8 Configuring the HP NetServer Configuring ISA Non-Plug-and-Play Boards (Optional) This section describes how to configure the NetServer for legacy or Non Plug-and-Play (non-PnP) ISA accessory boards. Reserving Resources for ISA Non-Plug-and-Play Boards If you have installed an ISA non-Plug-and Play accessory board, you must reserve system resources for it.
Page 61 Chapter 8 Configuring the HP NetServer 4. If a password has been set, provide it when prompted. 5. When the Setup Utility menu is displayed, use the right arrow key to select the Advanced menu. 6. Use the down arrow key to highlight PCI Configuration, and press Enter to select the submenu.
Page 62: Updating Bios
Chapter 8 Configuring the HP NetServer you to set the base address and block size of the non-PnP board that uses any memory segment with in the C800 and DFFF address range. If you are using this type of board and you are not using an ISA Configuration Utility (ICU) to specify its address range, you must select a base address from the six available options, [C800], [CC00], [D000], [D400], [D800], and [DC00].
Page 63: Setup Utility Factory Settings
Chapter 8 Configuring the HP NetServer NOTE You may find it helpful to save the Setup Utility (BIOS) configuration to a diskette after making the Setup Utility changes. If the CMOS is corrupted later, you will have a backup available to reload the Setup Utility configuration. Refer to the instructions on the HP Startup CD-ROM.
Page 64: Using The Scsi Configuration Utility
Chapter 8 Configuring the HP NetServer Using the SCSI Configuration Utility The HP NetServer uses the Symbios SCSI Select Utility to configure or changes SCSI settings. The SCSI Select Utility is used for verifying or modifying the SCSI controller settings for the devices connected to SCSI controller board. To access the SCSI Select Utility following the instructions on screen shortly after the NetServer begins the boot process, a message appears: <Ctrl A>...
Page 65: Troubleshooting
The following sections contain general procedures to help you locate installation problems. If you need assistance, it is recommended that you contact your reseller first. If you need to get assistance from Hewlett-Packard, refer to Appendix C, "Service and Support," for information on service and support.
Page 66: Netserver Will Not Power On
Chapter 9 Troubleshooting NetServer Will Not Power On Follow these steps if the power/activity light does not light green after you press the power-on button: 1. Remove the AC power cord, wait 15 seconds, reconnect the power cord, and try again. 2.
Page 67: Error Messages
Chapter 9 Troubleshooting If it is a hardware error, follow these steps: 1. Log all users off the network and power down the NetServer. 2. Remove the NetServer’s cover. WARNING Before removing the cover, always unplug telephone cables and disconnect the power cord. Unplug telephone cables to avoid exposure to shock hazard from telephone ringing voltages.
Page 68 Chapter 9 Troubleshooting 4. Verify the display’s contrast and brightness settings are correct. 5. Verify all internal cables are properly connected and all boards firmly seated. 6. Verify the processor module is fully seated in the slot on the system board. 7.
Page 69: Power-On Self Test (Post) Error Messages
Chapter 9 Troubleshooting NOTE HP recommends correcting the error before proceeding, even if the NetServer appears to start successfully. If you have corrected the problem displayed in the error message, but the POST still reports the error message after the NetServer starts, clear the CMOS configuration, as described in "Clearing the CMOS Configuration"...
Page 70 Chapter 9 Troubleshooting Message Corrective Action Floppy disk(s) This occurs if the BIOS can’t find or initialize the flexible failed disk drive controller or the flexible disk drive. If there is no flexible disk drive installed, ensure the drive selection in Setup is set to "None".
Page 71 Chapter 9 Troubleshooting Message Corrective Action Operating system Verify the boot drive has power and the correct data not found (IDE or SCSI) cables connected. Verify the hard drive cable is securely plugged into the system board (for IDE drives) or the SCSI controller board (for SCSI drives).
Page 72: Clearing The Cmos Configuration
Chapter 9 Troubleshooting Clearing the CMOS Configuration You may need to clear the CMOS configuration (BIOS) if the configuration has been corrupted. The CMOS could be corrupted by incorrect settings made in the Setup Utility, which could cause the display to be unreadable. The Setup Utility does not provide a method of clearing CMOS from within the Utility.
Page 73: Hardware Problems
Chapter 9 Troubleshooting Hardware Problems This section describes what to do if you have problems with your monitor, mass storage devices, printer, accessory boards, keyboard, or mouse. Monitor Does Not Work NOTE If the NetServer has a large amount of memory installed, it may take 30 seconds for the first screen to display.
Page 74: Keyboard Or Mouse Does Not Work
Chapter 9 Troubleshooting Keyboard or Mouse Does Not Work 1. Verify the keyboard and mouse are connected to the correct connectors. Refer to the color code on the rear panel of the NetServer and the color-coded keyboard and mouse connectors. 2.
Page 75: Ide Device Does Not Work
Chapter 9 Troubleshooting IDE Device Does Not Work If error messages display on the monitor indicating a failure of a IDE hard disk or tape backup device, perform these checks: 1. Verify the power cable is securely connected to the drive, and the flat IDE cable is securely connected to the drive and to the system board.
Page 76: Setup Utility Problems
Chapter 9 Troubleshooting 4. If necessary remove the accessory board preventing access to the battery. 5. Insert a small flat blade screwdriver or similar tool between battery and spring latch. See Figure 9-2. 6. Push the spring latch away from battery to release the battery. The spring contacts beneath the battery cause it to pop up allowing you to grasp the battery.
Page 77: Resetting Lost Passwords
Chapter 9 Troubleshooting Resetting Lost Passwords The Setup Utility allows you to recover the User password, if you have forgotten it. The User password can be reset if you know the Supervisor password, which allows you to enter the Setup Utility. User Password If you have forgotten the User password, but the Supervisor password is set and known, perform the following steps:...
Page 79: A Specifications
A Specifications Introduction This appendix provides the power requirements, operating conditions (environment requirements), physical requirements, hardware specifications, and video resolutions of the HP NetServer E 200. The system board layouts and the factory set jumpers are also provided. See Figures A-1 and A-2. The specifications and requirements listed below can vary if you install a mass storage device in the NetServer that has more stringent environmental limits.
Page 80 Appendix A Specifications Table A-2. Environment Requirements Parameter Range/Value Temperature Operating 5 to 35 C (41 to 95 F) Non-operating -40° to +65° C (-40° to +149° F) Humidity Operating 20% to 80% relative humidity, non-condensing Non-operating 5% to 95% relative humidity, non-condensing Altitude Operating...
Page 81 Appendix A Specifications Table A-4. Hardware Specifications Specification Characteristics Intel Pentium III processors: supported speeds 533 and Processors 600MHz; 512KB level 2 cache on processor. Chipset VIA Apollo Pro133 AGP2x set with 133Mhz front side bus speed support Supports up to three SDRAM DIMMs for a maximum total Memory (3 x 256 MB).
Page 82: System Board Layout
Appendix A Specifications Table A-5. Video Display Modes Max. Refresh Max. Refresh Max. Refresh Rate @ 256 Rate @ 65K Rate @ 16.7M Resolution Colors Colors Colors 640x480 200Hz 200Hz 200Hz 800x600 200Hz 200Hz 160Hz 1024x768 150Hz 150Hz 120Hz 1152x864 120Hz 120Hz 85Hz...
Page 83: Factory Default Jumper Settings
Appendix A Specifications Factory Default Jumper Settings This topic provides the factory default settings for jumpers and the location of connectors on the system board not called out in Figure A-1. The factory jumper settings should not be altered or it may cause damage to the system board or components on the board.
Page 84 Appendix A Specifications Item Supported/ Restricted Description Restricted to CPU Core/Bus Frequency Multiple jumpers supported CPUs 533Mhz CPU setting {BF3}={2-3} {BF2}={2-3} {BF1}={1-2} {BF0}={2-3} 600Mhz CPU setting {BF3}={1-2} {BF2}={2-3} {BF1}={1-2} {BF0}={2-3} Not supported Wake-On-Ring connector (WOR) Supported Clear CMOS jumper (CMOSCL) Normal (pins 1 and 2) Clear (pins 2 and 3) Not supported...
Page 85 Appendix A Specifications Figure A-2. Jumper and Connector Locations...
Page 87: B Regulatory Information
B Regulatory Information Regulatory Notices - Electromagnetic Compliance Electromagnetic Compatibility (EMC) requirements have been established in many countries to regulate the radio frequency energy generated by Information Technology Equipment (ITE). This energy is generated during the normal and intended use of this equipment and so it is limited by country regulations to levels intended to minimize potential interference to other electrical equipment, including public safety services.
Page 88: Notice For Canada (Industry Canada)
Hewlett-Packard’s system certification tests were conducted with HP-supported peripheral devices and HP shielded cables, such as those you receive with your computer. Changes or modifications not expressly approved by Hewlett-Packard could void the user’s authority to operate the equipment. Cables used with this device must be properly shielded to comply with the requirements of the FCC.
Page 89: Notice For Japan
Appendix B Regulatory Information For products labeled "Class B" This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. Notice for Japan The configuration of the NetServer you have purchased may be in either the class A or class B category.
Page 90: Notice For Korea
Appendix B Regulatory Information Notice for Korea The configuration of the NetServer you have purchased may be in either the class A or class B category. Class A Equipment: Please note that this equipment has been approved for business purposes with regards to electromagnetic interference, if purchased in error for use in residential area, you may wish to exchange the equipment where you purchased it.
Page 91 Appendix B Regulatory Information...
Page 92: Notice For Taiwan
Appendix B Regulatory Information Notice for Taiwan Class A Warning Statement Notice for European Union Radio Frequency Emissions Warning for Accessories This product has been found to comply with CISPR 22 Class B EMC emission limits. Installation and use of a Class A accessory creates a system that meets the requirements for industrial and commercial environments.
Page 93: Declaration Of Conformity (Us And Eu)
FCC Title 47 CFR, Part 15 Supplementary Information: 1) The product was tested in a typical configuration with Hewlett-Packard peripherals. 2) The product complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: é...
Page 94: Regulatory Notices - Product Safety
Appendix B Regulatory Information Regulatory Notices - Product Safety The following information applies only to NetServers with factory-installed components. CD-ROM Electrical Safety Statements The following information applies only to servers with factory-installed CD-ROM drives. CD-ROM Electrical Safety Statement – United States WARNING To prevent fire or shock hazard, do not expose the unit to rain or moisture.
Page 95 Appendix B Regulatory Information Laser Safety - Finland LASERTURVALLISUUS LUOKAN 1 LASERLAITE KLASS 1 LASER APPARAT HP NetServer E 200 - verkkopalvelimeen voidaan asentaa lisävarusteena laitteensisainen CD-ROM-lukulaite, joka on laserlaite. Kyseinen CD-ROM-lukulaite on käyttäjän kannalta turvallinen luokan 1 laserlaite. Normaalissa käytössä lukulaitteen suojakotelo estää laseräteen pääsyn laiteen ulkopuolelle.
Page 96: Battery Safety Statements
Appendix B Regulatory Information This CD-ROM Drive Unit is classified as a CLASS 1 CLASS 1 LASER PRODUCT. LASER PRODUCT The CLASS 1 LASER PRODUCT label is located LASSER on the top of the drive. KLASSE 1 PRODUKT Bei diesem CD-ROM-Laufwerk CDU56S handelt es sich um ein Laser-Produkt der Klasse 1.
Page 97: Noise And Ergonomic Safety Statements
Appendix B Regulatory Information Noise and Ergonomic Safety Statements Noise Declaration and Ergonomics - Germany Sound Pressure: LpA < 55 dB (A) am Arbeitsplatz, Beobachter Position (workplace, bystander position) normaler Betrieb (normal operation) nach DIN 45635 T. 19 (per ISO 7779) This product has not been evaluated for compliance with the ZH1/618 ergonomic requirements.
Page 99: C Service And Support
C Service and Support For all service and support information, see the HP NetServer Warranty and Service/Support Booklet included with your product.
Page 101: D Warranty And Software License
D Warranty and Software License Warranty See the HP NetServer Warranty and Service/Support Booklet included with your product for all warranty and service/support information. HP Software Product License Agreement ATTENTION: USE OF THE SOFTWARE IS SUBJECT TO THE HP SOFTWARE LICENSE TERMS SET FORTH BELOW. USING THE SOFTWARE INDICATES YOUR ACCEPTANCE OF THESE LICENSE TERMS.
Page 102: Non-Nuclear Usage
Appendix D Warranty and Software License If your Computer was shipped with a Recovery CD, (i) the Recovery CD and/or Support Utility software may be used only for restoring the hard disk of the HP computer system with which the Recovery CD originally was provided, and (ii) if separate EULA(s) are included with your Computer for any other MS products which are included on the Recovery CD, those MS products are subject to the terms of their respective EULA(s).
Page 103: Index
Index ISA non-Plug-and-Play boards, 54 connectors Factory restricted, 77 accessory boards connectors ISA non-Plug-and-Play, 54 system board, 77 adaptor settings, host, 58 control panel, 6, 9 AGP interrupt, 37 AGP video display modes, 76 LEDs, 6 switches, 6, 9 AGP video interrupt jumper, 38 cover removing, 13 replacing, 15...
Page 104 Index connectors, 77 interrupts Factory settings AGP, 37 jumpers, 77 ISA, 37 Setup Utility, 57 PCI, 37 feet USB, 37 setting, 17 IRQ resources, 55, 56 format disk, 58 ISA interrupt, 37 Front Panel, 5 ISA non-Plug and Play board, 54 ISA non-Plug-and-Play board, 54 hard disk drive formatting, 43...
Page 105 Index moving jumper mouse, 68 clearing password, 50 processor settings, 78 monitor Product Safety, 88 troubleshooting, 67 Monitor connecting, 41 rear panel ports, 41 mouse regulatory information, 81 troubleshooting, 68 Regulatory Notices - Electromagnetic Compliance, 81 Regulatory Notices - Product Safety, 88 NetServer removing the cover, 13 controls, 5...
Page 106 Index Setup steps, 1 time Setup Utility changing, 48 Factory settings, 57 troubleshooting Setup Utility, 43, 55 CD-ROM, 68 BIOS, 45 hardware problems, 67 changing system date and time, 48 IDE devices, 69 changing the boot order, 50 keyboard, 68 clearing CMOS, 52, 63, 66 monitor, 67 menu bar, 45...

This manual is also suitable for:

D7150a - netserver - e60 D9126av - netserver - e60 select express Netserver e 200

HP D6030A - NetServer - E50 Installation Manual

1 Setting up the HP Netserver

2 Controls, Ports, and Indicators

3 Opening and Closing the HP Netserver

4 Installing Mass Storage Devices

5 Installing Additional Memory

6 Installing Additional Boards

7 Connecting the Monitor, Keyboard, Mouse, and UPS

8 Configuring the HP Netserver

9 Troubleshooting

A Specifications

B Regulatory Information

C Service and Support

D Warranty and Software License

Index

Quick Links

Troubleshooting

Related Manuals for HP D6030A - NetServer - E50

Summary of Contents for HP D6030A - NetServer - E50

This manual is also suitable for:

Table of Contents