Asus P5WDG2 WS Professional User Manual page 60

I m p o r t a n t n o t e s o n S e r i a l A T A I m p o r t a n t n o t e s o n S e r i a l A T A I m p o r t a n t n o t e s o n S e r i a l A T A
I m p o r t a n t n o t e s o n S e r i a l A T A I m p o r t a n t n o t e s o n S e r i a l A T A
•
•
Serial ATA hard disk drive connection Serial ATA hard disk drive connection
Serial ATA hard disk drive connection Serial ATA hard disk drive connection Serial ATA hard disk drive connection
C o n n e c t o r C o n n e c t o r C o n n e c t o r
C o n n e c t o r C o n n e c t o r
S A T A 1 / S A T A 2 S A T A 1 / S A T A 2 S A T A 1 / S A T A 2 S A T A 1 / S A T A 2 S A T A 1 / S A T A 2
S A T A 3 / S A T A 4 S A T A 3 / S A T A 4
S A T A 3 / S A T A 4 S A T A 3 / S A T A 4 S A T A 3 / S A T A 4
4 . 4 . 4 . M a r v e l l M a r v e l l
4 . 4 . M a r v e l l M a r v e l l M a r v e l l
( 7 - p i n E X T _ S A T A 1 , E X T _ S A T A 2 , E X T _ S A T A 3 ) ( 7 - p i n E X T _ S A T A 1 , E X T _ S A T A 2 , E X T _ S A T A 3 ) ( 7 - p i n E X T _ S A T A 1 , E X T _ S A T A 2 , E X T _ S A T A 3 )
( 7 - p i n E X T _ S A T A 1 , E X T _ S A T A 2 , E X T _ S A T A 3 ) ( 7 - p i n E X T _ S A T A 1 , E X T _ S A T A 2 , E X T _ S A T A 3 )
These connectors are for Serial ATA signal cables. These connectors
support Serial ATA hard disk drives.
Set the M a r v e l l S A T A C o n t r o l l e r
items in the BIOS to [Enabled] to use the connectors to build a RAID
set. See section "4.4.6 Onboard Devices Configuration" for details.
P5WDG2-WS PRO SATA 3 Gbps connector
Before creating a RAID set using Serial ATA hard disks, make sure that
you have connected the Serial ATA signal cables and installed Serial ATA
hard disk drives; otherwise, you cannot enter the Marvell
RAID utility.
2 - 3 4 2 - 3 4
2 - 3 4 2 - 3 4 2 - 3 4
You must install Windows
Service Pack 1 before using Serial ATA hard disk drives. The Serial
ATA RAID feature (RAID 0/RAID 1/RAID 5/RAID 10) is available only
if you are using Windows
When using the connectors in S S S S S t a n d a r d I D E
primary (boot) hard disk drive to the SATA1 or SATA2 connector.
Refer to the table below for the recommended SATA hard disk drive
connections.
C o l o r C o l o r C o l o r
C o l o r C o l o r
R e d R e d R e d R e d R e d
B l a c k B l a c k
B l a c k B l a c k B l a c k
® ® ® ® ® 8 8 S E 6 1 4 x 8 8 S E 6 1 4 x S e r i a l A T A c o n n e c t o r s S e r i a l A T A c o n n e c t o r s
8 8 S E 6 1 4 x 8 8 S E 6 1 4 x 8 8 S E 6 1 4 x S e r i a l A T A c o n n e c t o r s S e r i a l A T A c o n n e c t o r s S e r i a l A T A c o n n e c t o r s
M a r v e l l S A T A C o n t r o l l e r M a r v e l l S A T A C o n t r o l l e r and M a r v e l l S A T A B O O T R O M M a r v e l l S A T A C o n t r o l l e r
M a r v e l l S A T A C o n t r o l l e r
® 2000 Service Pack 4 or the Windows
® 2000/XP/Server 2003 or later version.
t a n d a r d I D E t a n d a r d I D E
t a n d a r d I D E t a n d a r d I D E mode, connect the
S e t t i n g S e t t i n g S e t t i n g
S e t t i n g S e t t i n g
M a s t e r M a s t e r M a s t e r M a s t e r M a s t e r
S l a v e S l a v e
S l a v e S l a v e S l a v e
M a r v e l l S A T A B O O T R O M M a r v e l l S A T A B O O T R O M M a r v e l l S A T A B O O T R O M
M a r v e l l S A T A B O O T R O M
EXT_SATA3 EXT_SATA2
C h a p t e r 2 : H a r d w a r e i n f o r m a t i o n C h a p t e r 2 : H a r d w a r e i n f o r m a t i o n
C h a p t e r 2 : H a r d w a r e i n f o r m a t i o n C h a p t e r 2 : H a r d w a r e i n f o r m a t i o n C h a p t e r 2 : H a r d w a r e i n f o r m a t i o n
® XP
U s e U s e U s e
U s e U s e
B o o t d i s k B o o t d i s k B o o t d i s k B o o t d i s k B o o t d i s k
D a t a d i s k D a t a d i s k
D a t a d i s k D a t a d i s k D a t a d i s k
EXT_SATA1
® 88SE6141