Searching Categories; Parental Lock; Ipod ® Playback; Preparations - Denon DHT-589BA Owner's Manual

Searching Categories

1
[o p]
Press .
C A T E G O R Y S E A R C H
Channel category
C A T : P o p s
2
[o p]
Use to select the category, then use
select the desired channel.
• "UPDATING" is displayed while the encording code is being
updated.
• "SIRIUS UPDATING" is displayed when updating SIRIUS tuner
firmware.
• Refer to "Troubleshooting" (vpage 52) regarding other messages.

Parental Lock

1
Tune to the channel you want to lock.
2
[ENTER]
Press for at least 3 seconds.
"Code: [ ]" is displayed.
3
Enter the 4-digit lock code using uiop
When you enter the correct code, the corresponding channel is
locked.
4
[ENTER]
Press .
• Channels under Parental Lock cannot be tuned in by performing
Tuning Up/Down or by category search.
• Channels stored in preset memory can be tuned in by the preset
channel select operation, even if Parental Lock is applied.
• When a channel to which Parental Lock is applied is being played,
Parental Lock for that channel is cancelled by performing Step 2.
• See "Edit Lock Cord" (vpage 25) for the method of changing
Parental Lock Cord.
• You can also set "Parental Lock" from the system setup (vpage
25).
iPod ® Playback
The music on an iPod can be played by using the control dock for
iPod (ASD-1R, ASD-11R, ASD-3N or ASD-3W, sold separately).
The operation can also be performed using the buttons on the
remote control unit.
iPod is a trademark of Apple Inc., registered in the U.S.
and other countries.
b The iPod may only be used to copy or play contents that are not
copyrighted or contents for which copying or playback is legally
[ui] permitted for your private use as an individual. Be sure to comply
to
with applicable copyright legislation.

Preparations

1
Make the necessary preparations.
q S et the iPod in the DENON control dock for iPod.
(vSee the control dock for iPod's operating instructions.)
w Assign the control dock for iPod's input.
The input for the control dock for iPod is assigned to VCR by
default.
"System Setup" – "Input Setup" – "iPod Assign"
(vpage 24)
2
<SOURCE SELECT>
Either turn
select the input source assigned in step 1-w above.
.
3
[SOURCE CONTROL 1]
Set
CONTROL 2]
to "iPod/NETWORK".
(v page 42 "Remote Control Unit Operations")
4
Press
more to select the display mode.
To switch between modes, press and hold down the button.
When remote mode is active, "Remote" is displayed.
[Selectable mode]
Display location
Playable
files
Active
buttons
z1 : When using an ASD-3N or ASD-3W control dock for iPod
z2 : Video may not be output, depending on the combination of
ASD-1R or ASD-11R and iPod.
• With the default settings, the iPod can be used connected to the VCR
(iPod) connector.
• Use the RESTORER mode to expand the low and high frequency
components of compressed audio files and achieve a richer sound.
The default setting is "Mode3" (vpage 32).
<ON/STANDBY>
• Press
the standby mode before disconnecting the iPod. Also switch the
input source to one to which "iPod Assign" is not assigned before
[iPod]
or press to
disconnecting the iPod.
• When using an ASD-3N or ASD-3W control dock for iPod, refer to the
respective manual to operate.
[SOURCE
to "AUDIO" and
[MODE]
and hold it down for a 2 seconds or
Browse mode Remote mode
Main unit display iPod display
Audio file
S
Video file
S z1 S z2
Remote
control unit
S
(AVR-589)
iPod
A
[OFF]
or and set the AVR-589's power to
ENGLISH
S
S
S
.