Mounting the Cradle . . . . . . . . . . . . . . 14 use a solid-state speed control with this fan. Use only Hunter speed controls, which are solid state.
Page 3
If you want to use an existing fan site, complete the following checklist to System determine if the site is acceptable and safe for your new Hunter fan. If you cannot check off every item, prepare a new fan site as described on this page.
Page 4
ANSI/NFPA 70. If your ceiling fan, go to your fan manual and continue with Section 2 • Installing the you are unfamiliar with wiring, use a Ceiling Plate. qualified electrician. 45084-01 • 01/17/12 • Hunter Fan Company...
Page 5
Support Brace Hunter’s patented 2-position mounting system provides you maximum installation flexibility and ease. You can install your Hunter fan in one of two ways, depending on ceiling height and your preference: Standard or Angled mounting. The steps in this manual include instructions for Ceiling both Installer’s Choice mounting methods.
• Drill holes for and install wood screws. • Identify and connect electrical wires. • Lift 40 pounds. If you need help installing the fan, your Hunter fan dealer can direct you to a licensed installer or electrician. Gathering the Tools You will need the following tools for installing the fan: •...
Tighten the screws into the 9/64” pilot holes; do not use lubricants on the screws. Do not over tighten. Flat Washer Steps 2-2 – 2-4 Ceiling Peak Ceiling Peak Large Large Opening Opening 3” Screw LEFT RIGHT Step 2-3 (Angled Ceiling Only) 45084-01 • 01/17/12 • Hunter Fan Company...
(Rotate the fan until you hear the notch pop into place.) Go to 4 • Wiring the Fan . WARNING: Fan may fall if not assembled as directed in these installation instructions. Indent Steps 3-4 – 3-5 45084-01 • 01/17/12 • Hunter Fan Company...
Page 9
4-6. Close the clamp by securely tightening the nuts. 4-7. Coil up the excess cable. 4-8. Return to the fan so you can complete the fan wiring. Steps 4-3 – 4-7 Wire Clamp 45084-01 • 01/17/12 • Hunter Fan Company...
5-7. Spread the wires apart, with the grounded wires on one side of the outlet box and the ungrounded wires on the other side of the outlet box. 45084-01 • 01/17/12 • Hunter Fan Company...
6-6. Twist canopy trim ring clockwise to secure the canopy. Should you need to remove the canopy trim ring: 1. Twist canopy trim ring counter clockwise until it releases from canopy. Step 6-3 Step 6-4 Canopy Step 6-5 Screw 45084-01 • 01/17/12 • Hunter Fan Company...
Step 7-2 Note: The blades on this fan have been treated with Hunter’s Dust Armor protection, making the blades less likely to attract dust and dirt. Use a dry or slightly damp lint free cloth to clean the blades.
Housing with three housing assembly screws. Note: This fan is not compatible with any light kit. Step 8-3 Switch Housing Assembly Screw Lower Switch Step 8-4 Housing 45084-01 • 01/17/12 • Hunter Fan Company...
9-5. Mount the faceplate (not included) to the control with two #6-32 screws that you removed earlier from the faceplate. 9-6. Attach the knob onto the post on the speed control and turn to the left for the OFF position. Step 9-5 Step 9-6 45084-01 • 01/17/12 • Hunter Fan Company...
(clockwise blade rotation) will distribute the warmer air trapped at the ceiling around the room without causing a draft. 10-4. The blades on this fan have been treated with Hunter’s Dust Armor protection, making the blades less likely to attract dust In warm weather, use and dirt.
If you need parts or service assistance, please call 888-830-1326 (In Canada, call 1-866-268-1936) or visit us at our website at http://www.hunterfan.com. Hunter Fan Company 7130 Goodlett Farms Pkwy. #400 Memphis, Tennessee 38016 45084-01 • 01/17/12 • Hunter Fan Company...