For document management system and printer (221 pages)
Summary of Contents for Kyocera KM-4800w
Page 1
PS Printer Driver for Windows Vista User’s Manual...
Page 2
Regarding this manual This manual explains how to install Windows PS Printer Driver and how to use it. This PS Printer Driver can be used with Microsoft Windows Vista. NOTE: To use KM-4800w-PS Printer Driver, “UG-32” Option License is required.
Installation Method 1.1. Install TCP/IP Port NOTE: If KM-4800wEN printer is already installed on your system, TCP/IP Port installation has been completed at the same time. Please go to [1.2 Add Printer] to continue the printer installation. 1. Insert Installation Disk in CD-ROM driver. 2.
1.2. Add Printer 1. Launch “Printers” in Control Panel. 2. Right-click within a blank region and select “Run as administrator” and “Add Printer”. [Windows needs your permission to continue] will appear. Click “Continue”.
Page 8
3. Click “Add a local printer”. 4. Select “Create a new port”. Select “KM-4800w TCP/IP Port” in the pull-down menu for port types. Click “Next”. If "KM-4800w TCP/IP Port" exists, select "Use an existing port:" and specify the "KM-4800w TCP/IP Port" from the pull-down menu.
Page 9
5. Enter the KM-4800w’s IP address or host name. Click “OK”. 6. Click “Have Disk”.
Page 12
11. If KM-4800w PS Printer Driver is already installed on your system, the following screen appears. Select “Replace the current driver” and click “Next”. 12. Printer name can be changed at your option. Click “Next”.
Page 13
13. Check “Always trust software from “KYOCERA MITA Corporation”.” and click “Install”. 14. Please wait while the wizard is installing the components.
Page 14
15. Select “Do not share this printer” and click “Next”. 16. Click “Finish”. Installation of printer has been finished.
1.3. About Printer Port Select the printer you have added by right-click, and select “Run as administrator” and “Properties”. [Windows needs your permission to continue] will appear. Click “Continue”.
Page 16
Select the “Ports” Tab. Select “KM-4800w:192.168….Port”, and click “Configure Port”.
Page 17
The following information is indicated. You do not have to change any of the above settings in usual case. Change these settings when KM-4800w does not wake up correctly from the Power Save Mode caused by the network settings. MAC Address: MAC Address of output printer...
1.4. About reinstall of Printer When reinstalling KM-4800wEN-PS to the system, first delete the existing KM- 4800wEN-PS components. Select a printer to be deleted. Right-click on it and select “Run as administrator” and “Delete”. [Windows needs your permission to continue] will appear. Click “Continue”. Click “Yes”.
Page 19
Right-click within a blank region and select “Run as administrator” and “Server Properties”. [Windows needs your permission to continue] will appear. Click “Continue”.
Page 20
Select the “Drivers” Tab. Select “KM-4800wEN-PS” and click “Remove”.
Page 21
Select “Remove driver and driver package” and click “OK”. Click “Yes”. Click “Delete”.
Page 22
Click “OK”. If the removal of the driver is failed, reboot the PC, and then try to remove the driver again. Click “Close”. Now the system is ready to be reinstalled KM-4800wEN-PS.
Setting item of Printer Driver If the setup conditions of the application is not correct, documents may not be printed properly. Select the printer you have installed by right clicking, and then open “Printing Preferences”. Each setting item in “Layout” Tab is explained on and after the next page.
Page 24
< Orientation > Orientation of paper can be selected. “Rotated Landscape” rotates a “Landscape” image 180 degrees around. <Page Order> “Front to Back” outputs a multiple page file from the first page to the last page. “Back to Front” outputs a multiple page file from the last page to the first page. <Page Format>...
Page 25
Each setting item in “Advanced” is explained below. <Paper/Output> <Paper Size> Specify the size of paper used for printing. If “Custom Size” is selected in the above setting, the following dialog is indicated. A paper size can be specified at your option within the following range. Width: 210 mm to 914.4 mm Height: 297 mm to 10000 mm...
Page 26
<Copy Count> Number of prints can be specified. Available count ranges from 1 to 9999 but the guarantee range of proper operation is from 1 to 999. Checking “Collate” enables to print sets with collating. <Graphic> <Print Quality> Printing resolution can be specified. The printing resolution is normally set to 600dpi.
Page 27
<PostScript Options> <PostScript Output Option> This should be normally set to “Optimize for Speed”. <True Type Font Download Option> This should be normally set to “Automatic”. <PostScript Language Level> This should be set to “Level 3”. <Send PostScript Error Handler> This should be normally set to “No”.
Page 28
PS Printer Driver for Windows Vista User’s Manual 2008. 7 Rev. 1.0 The Copyright Act protects this manual. It is prohibited to copy or duplicate all or a part of this manual without permission.