Earn BISSELL Rewards! Earn BISSELL Rewards! egister your egister your product today! product today! See details on See details on back page back page USER'S GUIDE 81M9 SERIES Thank You Safety Instructions Product View Assembly Operations Maintenance and Care 10-15...
Page 2
Your BISSELL vacuum is well made, and we back it with a limited three year warranty. We also stand behind it with a knowledgeable, dedicated Consumer Care department, so, should you ever have a problem, you’ll...
MPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic Turn off all controls before plugging or ■ precautions should be observed, including unplugging vacuum cleaner. the following: Use extra care when cleaning stairs. ■ Read all Unplug before attaching the TurboBrush Tool.
ssembly WaRning: tools needed: philips head screwdriver. attach handle to vacuum Do not plug in your vacuum cleaner until you are familiar 1. Locate vacuum handle and the bag that with all instructions and contains extension wand support, lower operating procedures. cord wrap, and screws.
ssembly attach carpet spot & stain remover pet holster 1. Locate the bag that contains carpet spot & stain remover holster and can. 2. Attach holster to left side of vacuum (when viewing from front) by lining up the two tabs on the back side of the holster with the two openings on the vacuum.
perations handle positions 1. In upright position, tilt cleaner back on its rear wheels to transport from room to room. The vacuum can also be moved by using the carrying handle on front of the vacuum. 2. Using your foot, press handle release pedal on the lower left side of the vacuum to recline vacuum in cleaning position.
Page 8
& stain Remover* Your new vacuum comes with BISSELL OxyPro ® , OxyPro ® Pet, or Professional Oxy Total ® , which remove tough stains and odors from carpet. These items are available for purchase by visiting the BISSELL website www.bissell.com.
perations using the tools attach desired tool to hose for above floor cleaning surfaces or hard to reach areas. 1. Remove Hose: With vacuum in upright position, remove hose end from the suction inlet near the bottom of the vacuum by the wheel.
aintenance and care to maximize performance and extend life of your vacuum it is very important to perform the following maintenance steps. empty dirty container Empty when dirt reaches the “Full” line on t he container 1. Turn power OFF. Unplug power cord from electrical outlet.
aintenance and care cleaning the pre-motor filter Check pre-motor filter and wash as needed based on frequency of cleaning. 1. Turn power OFF. Unplug power cord from electrical outlet. 2. The pre-motor filter protects motor from debris and is located in the slide out tray underneath the dirt container.
aintenance and care check rotating floor brush and drive belt It is recommended to check your vacuum’s rotating floor brush and drive belt regularly for wear or damage. 1. Turn power OFF. Unplug power cord from electrical outlet. 2. Place handle in low cleaning position turn vacuum over so bottom side is facing up.
If the cleaner will not turn on or the thermal protector continues to activate, your cleaner may need servicing. Call BISSELL Consumer Care or visit the website to locate an authorized Service Center. note: the thermal protector con- trols the main vacuum motor only, not the brush motor.
aintenance and care clearing clogs Low suction or poor pickup may be due to a clog in the vacuum. If you notice a change in the sound of the vacuum motor, check for clogs. 1. Turn power OFF. Unplug power cord from electrical outlet.
Page 15
aintenance and care turbobrush tool maintenance ® Note: Model 81M9-1 comes with the Pet TurboBrush ® Tool and follows same maintenance instructions. 1. Turn power OFF. Unplug vacuum cord from electrical outlet 2. Twist collar so opening is at the top and lift top cover to remove 3.
WaRning: roubleshooting To reduce the risk of electric shock, turn power OFF and disconnect polarized plug from electrical outlet before performing maintenance or troubleshooting. Vacuum cleaner won’t turn on possible causes Remedies Power cord not plugged in 1. Check electrical plug Blown fuse/tripped breaker in home 2.
Page 18
® 95C9 Professional Oxy Total Carpet Spot & Stain Remover ® dditional accessories these items are available for purchase as accessories for your bissell vacuum: to purchase call 1-800-237-7691 or visit www.bissell.com. Item Part No. Part Name 203-1056 Crevice Tool...
This warranty gives you specific legal rights, and you may also have other rights which may vary from state to state. If you need additional instruction regarding this warranty or have questions regarding what it may cover, please contact BISSELL Consumer Care by E-mail, telephone, or regular mail as described below.
Page 20
Grand Rapids MI 49501 ATTN: Consumer Services Or visit the BISSELL website -www.bissell.com When contacting BISSELL, have model number of cleaner available. Please record your Model Number: ___________________ Please record your Purchase Date: ___________________ note: please keep your original sales receipt. it provides proof of purchase date in the event of a warranty claim.