Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Eizo FlexScan F520
Summary of Contents for Eizo FlexScan F520
- Page 1 English User’s Manual FlexScan F520 Color Display Monitor...
-
Page 2: Table Of Contents
4 CLEANING ...18 5 SPECIFICATIONS ... 19 Copyright© 1999 by EIZO NANAO CORPORATION. All rights reserved. No part of this manual may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, or otherwise, without the prior written permission of EIZO NANAO CORPORATION. -
Page 3: Precautions
PRECAUTIONS IMPORTANT! * This product has been adjusted specifically for use in the region to which it was originally shipped. The performance of the product, (i.e. picture geometry, picture positioning and color convergence and purity in the case of color monitors) is optimally adjusted to the earth's magnetic field of the specific destination. - Page 4 WARNING • If the monitor begins to emit smoke, smells like something is burning, or makes strange noises, disconnect all power connections immediately and contact your dealer for advice. Attempting to use a malfunctioning monitor can be dangerous. • Do not dismantle the cabinet or modify the monitor. Dismantling the cabinet or modifying the monitor may result in electric shock or burn.
- Page 5 • Do not overload your power circuit, as this may result in fire or electric shock. • For proper connections of the power cord, be certain to plug the power cord to the provided monitor connector and directly to a wall outlet.
- Page 6 • Do not remove the tilt-swivel stand. The stand is required to maintain clearance for the ventilation slots on the bottom of the cabinet. Removing the stand will block these slots and may result in fire or electric shock. • Do not touch the plug with wet hands. Touching the plug with wet hands is dangerous and can cause electrical shock.
-
Page 7: Introduction
INTRODUCTION About This Manual This manual explains the precautions, specifications, and operation of your EIZO monitor. Please read through this manual as it will help you to get the most out of your monitor. Controls & Connectors: Front ™ QuickSet Control pad (hereinafter “Control pad”) -
Page 8: Installation
Macintosh An optional Macintosh adapter should be connected to the PC (if required) before connecting the signal cable. Please consult EIZO dealer. 4) Plug the power cord into the power connector at the rear of the monitor. Then plug the other end of the cord into a power outlet. -
Page 9: Setting The Resolution
WARNING • Use the enclosed power cord. If using the power cord other than the enclosed one, use the following cord. In USA and Canada, use a UL LISTED/CSA LABELED or CERTIFIED power cord set meeting the following specifications: * Rating: min. -
Page 10: Screen Adjustment
2 SCREEN ADJUSTMENT 2-1. How to use the ScreenManager Entering the ScreenManager Press the ENTER key to display the ScreenManager Main menu. Making the Adjustments and Settings 1) Select the desired icon using the Arrow keys, and then press the ENTER key to display the each adjustment/setting menu. - Page 11 Contrast/ Brightness Size Position Side- Pin Balance/ Side- Pincushion Parallelogram/ Trapezoidal Tilt Moiré Function (Arrow Keys Used) Adjusts: a) Contrast (left/right) b) Brightness (up/down) · When a white text against a black background (e.g., DOS text) is used, setting the brightness at its maximum is recommended because a dark setting will result in eye strain due to high character contrast.
- Page 12 Complete energy use can only be stopped by disconnecting the monitor from the power supply. • When the monitor is in a power saving mode, the optional EIZO i·Sound speaker unit will turn off. • Off Timer will work while PowerManager is active, but there will be no advance notice before the monitor's power switches off.
- Page 13 VESA DPMS What is VESA DPMS? The acronym VESA stands for “Video Electronics Standards Association,” and DPMS stands for “Display Power Management Signaling.” DPMS is a munication standard that PCs and graphics boards use to implement power savings at the monitor side. Set-up Procedure 1) First, make the appropriate settings for the PC.
-
Page 14: Shortcut Keys
To Delay Entering the “Off Timer Mode” To delay entering the “Off Timer Mode”, press any keys on the front panel located to the left of the power switch during the “Advance notice Mode”. The monitor will continue to operate for an additional 90 minutes. There will be another advance notice for 15 minutes as described. -
Page 15: Troubleshooting
3 TROUBLESHOOTING Troubleshooting If a problem persists even after applying the suggested remedies, contact an EIZO dealer. Problems 1) Indicator status: OFF 2) Indicator status: GREEN 3) Indicator status: GREEN (flashing) 4) Indicator status: YELLOW 5) Indicator status: YELLOW (flashing) 6) Following message appears. - Page 16 It may be solved by switching off or moving the interfering device, or by relocating the monitor. If the volume level of the EIZO optional i·Sound speaker is too high, it may, in some cases, cause a slight vibra-...
- Page 17 PC and operating system. Flicker will occur with interlaced scanning, or non-interlaced scanning with a low refresh rate. All EIZO monitors are capable of reproducing high refresh rates for non-interlaced scanning. If a problem occurs when using a non-interlaced signal, try adjusting the graphics board to increase the refresh rate (if possible).
-
Page 18: Cleaning
4 CLEANING WARNING • Keep liquids away from the monitor. Spillage into the cabinet may result in fire, electric shock, or equipment damage. If an object or liquid falls/spills into the cabinet, unplug the monitor immediately. Have the unit checked by a qualified service engineer before using it again. -
Page 19: Specifications
* The actual size displayed can be dependent on the graphics board or PC utilized. 100-120 VAC±10%, 50/60 Hz, 1.1 A 220-240 VAC±10%, 50 Hz, 0.55 A 80 W/95 W (with EIZO optional speaker attached) D-Sub mini 15-pin • H/V Separate, TTL, Positive/Negative • H/V Composite, TTL, Positive/Negative •... -
Page 20: Preset Timing
Preset Timing 8 factory presets shown below have been registered in the monitor’s microprocessor. Resolution 720 × 400 (text) 640 × 480 640 × 480 VESA 800 × 600 VESA 1024 × 768 VESA 1024 × 768 VESA 1280 × 1024 VESA 1280 ×... -
Page 21: Why Do We Have Environmentally Labelled Computers
Congratulations! You have just purchased a TCO’99 approved and labelled product! Your choice has provided you with a product developed for professional use. Your purchase has also contributed to reducing the burden on the environment and also to the further development of environmentally adapted electronics products. -
Page 22: Environmental Requirements
Environmental requirements Flame retardants Flame retardants are present in printed circuit boards, cables, wires, casings and housings. Their purpose is to prevent, or at least to delay the spread of fire. Up to 30% of the plastic in a computer casing can consist of flame retardant substances. Most flame retardants contain bromine or chloride, and those flame retardants are chemically related to another group of environmental toxins, PCBs. -
Page 23: Fcc Declaration Of Conformity
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Note Use the attached specified cable below or EIZO signal cable with this monitor so as to keep interference within the limits of a Class B digital device. -AC Cord -Shielded Signal Cable (D-SUB mini 15 pin - D-SUB mini 15 pin, the enclosed signal cable) This Class B digital apparatus complies with Canadian ICES-003. - Page 24 Röntgenstrahlung ist durch die eigensichere Kathodenstrahlroehre ausreichend abgeschirmt. Recycle Auskunft Die Rücknahme dieses Produktes nach Nutzungsende übernimmt EIZO in Deutschland zusammen mit dem Partner von Roll MBB Recycling GmbH. Dort werden die Geräte in ihre Bestandteile zerlegt, die dann der Wiederverwertung zugeführt werden.