Sharp PG-LW3000 Operation Manual
  1. Manuals
  2. Brands
  3. Sharp Manuals
  4. Projector
  5. PG-LW3000
  6. Operation manual

Sharp PG-LW3000 Operation Manual

Hide thumbs Also See for PG-LW3000:
Table of Contents

Advertisement

Quick Links

DATA PROJECTOR
MODEL
PG-LX3000
PG-LX3500
PG-LW3000
PG-LW3500
OPERATION MANUAL

Advertisement

Table of Contents
loading

Related Manuals for Sharp PG-LW3000

Summary of Contents for Sharp PG-LW3000

  • Page 1 DATA PROJECTOR MODEL PG-LX3000 PG-LX3500 PG-LW3000 PG-LW3500 OPERATION MANUAL...
  • Page 2 IMPORTANT • For your assistance in reporting the loss Model No.: or theft of your Projector, please record the Model and Serial Number located on the bottom of the projector and retain this Serial No.: information. • Before recycling the packag i ng, please ensure that you have checked the con­ tents of the carton thoroughly against the list of “Supplied accessories” on page 3. SPECIAL NOTE FOR USERS IN THE U.K.
  • Page 3 2. CONSUMER PRODUCT SAFETY ACT To ensure that you will promptly receive any safety notification of inspection, modification, or recall that SHARP may be required to give under the 1972 Consumer Product Safety Act, PLEASE READ CAREFULLY THE IMPORTANT “LIMITED WARRANTY” CLAUSE.

  • Page 4: Product Disposal

    • Make sure to reset the lamp timer only when replacing the lamp. If you reset the lamp timer and continue to use the same lamp, this may cause the lamp to become damaged or explode. ■ Carefully change the lamp by following the instructions described on pages to 65. * If you wish, you may have the lamp replaced at your nearest Sharp Authorized Projector Dealer or Service Center. * If the new lamp does not light after replacement, take your projector to the nearest Sharp Authorized Projector Dealer or Service Center for repair.

  • Page 5: Accessories

    For U.K. and Canada, etc. except U.K. Singapore (6' (1.8 m)) (6' (1.8 m)) (6' (1.8 m)) <QACCDA083WJPZ> <QACCVA025WJPZ> <QACCBA105WJPZ> * W hich power cords are supplied along with your projector depends on the region. Use the power cord that corresponds to the wall outlet in your country. • Initial setup guide <TINS­F649WJZZ> • CD­ROM <UDSKAA139WJZZ> Note • Codes in “< >” are Replacement parts codes. Optional accessories ■ Lamp unit AN­LX30LP AN­60KT ■ Ceiling­mount adaptor ■ Ceiling­mount bracket AN­XRCM30 (for U.S.A. only) AN­TK201 <for AN­60KT> ■ Ceiling­mount unit AN­TK202 <for AN­60KT> ■ Ceiling­mount extension tube AN­EP101B <for AN­XRCM30> (for U.S.A. only) Note • Some of the optional accessories may not be available depending on the region. Please check with your nearest Sharp Authorized Projector Dealer or Service Center.

  • Page 6: Table Of Contents

    Contents Preparing Introduction Displaying the Black Screen and Turning Off the Sound Temporarily ..29 Resize Mode .......... 30 Accessories ..........3 Contents ..........4 Useful Features IMPORTANT SAFEGUARDS ....6 Part Names and Functions ....10 Operating with the Remote Control..34 Top View ..........10 Displaying and Setting the Front View ..........10 Rear View (Terminals) ......11 Break Timer ......... 34 Displaying the Pointer ......34 Inserting the Batteries .
  • Page 7 Removing and Installing the Lamp Unit ... 64 Resetting the Lamp Timer ...... 65 Compatibility Chart ......66 Troubleshooting ........68 For SHARP Assistance ......71 Specifications ........72 Dimensions ...........73 Index .............74 • In this operation manual, the illustration and the screen display are simplified for explanation, and...

  • Page 8: Important Safeguards

    IMPORTANT SAFEGUARDS CAUTION: Please read all of these instructions before you operate this product and save these instructions for later use. Electrical energy can perform many useful functions. This product has been engineered and manufactured to assure your personal safety. BUT IMPROPER USE CAN RESULT IN POTENTIAL ELECTRICAL SHOCK OR FIRE HAZARDS. In order not to defeat the safeguards incorporated in this product, observe the following basic rules for its installation, use and servicing. 1. Read Instructions 10. Ventilation Slots and openings in the cabinet are provided All the safety and operating instructions for ventilation to ensure reliable operation of should be read before the product is the product and to protect it from overheating, operated. and these openings must not be blocked or 2. Retain Instructions covered. The open i ngs should never be The safety and operating instructions blocked by placing the product on a bed, sofa,...

  • Page 9: Replacement Parts

    15. Overloading 19. Replacement Parts Do not overload wall outlets, extension cords, When replacement parts are required, be or integral convenience receptacles as this sure the service technician has used can result in a risk of fire or electric shock. replace m ent parts specified by the 16. Object and Liquid Entry manufacturer or have the same characteristics as the original part. Never push objects of any kind into this Unauthorized substitutions may result in product through openings as they may touch fire, electric shock, or other hazards. dangerous voltage points or short­out parts 20. Safety Check that could result in a fire or electric shock. Never spill liquid of any kind on the product. Upon completion of any service or repairs 17. Servicing to this product, ask the service technician to per f orm safety checks to determine that Do not attempt to service this product the product is in proper operating yourself as opening or removing covers condition.
  • Page 10 Internal cleaning ■ Protect the lens so as not to hit or damage should only be performed by a Sharp the surface of the lens. Authorized Projector Dealer or Service Center.
  • Page 11 Caution regarding usage of the projector Temperature monitor function ■ If you are not to use the projector for a long time or before moving the projector, make certain you unplug the power cord from the wall outlet, and disconnect any other cables connected to it.

  • Page 12: Part Names And Functions

    Part Names and Functions Numbers in refer to the main pages in this operation manual where the topic is explained. 16 17 Top View Front View Zoom ring Temperature warning indicator For enlarging/reducing the picture. Lamp indicator Focus ring Power indicator For adjusting the focus. STANDBY/ON button Intake vent F or turning the power on and putting the projector into Standby mode.

  • Page 13: Rear View (Terminals)

    Rear View (Terminals) LAN terminal 20, 21, 22 HDMI terminal Terminal for controlling the projector using Terminal for HDMI input. a computer via network. A UDIO 2 input terminal RS-232C terminal Terminal for controlling the projector using V IDEO input terminal a computer. Terminal for connecting video equipment. Exhaust vent C OMPUTER/COMPONENT 1 input Speaker...
  • Page 14 Part Names and Functions (Continued) Numbers in refer to the main pages in this operation manual where the topic is explained. POINTER button For displaying the pointer. Adjustment buttons (P/R/O/Q) For selecting and adjusting menu items. EFFECT button For changing the pointer or spot area. KEYSTONE button For entering the Keystone Correction mode. FUNCTION button For operating and executing a function assigned to “FUNCTION Button”. VOL +/– (Volume) buttons For adjusting the speaker sound level.

  • Page 15: Inserting The Batteries

    Inserting the Batteries Pull down the tab on the cover and remove the cover towards the direction of the arrow. Insert the batteries. • Insert the batteries making sure the polarities correctly match the m and n marks inside the battery compartment. Insert the lower tab of the cover into the opening, and lower the cover until it clicks in place. Incorrect use of the batteries may cause them to leak or explode.

  • Page 16: Easy Start

    Easy Start This section shows the basic operation (projector connecting with the computer). For details, see the page described below for each step. Setup and Projection In this section, connection of the projector and the computer is explained using one example. STANDBY button STANDBY/ON button...
  • Page 17 4. Adjust the projected image with the Setup Guide After the projector turns on, the Setup Guide appears. (When “Setup Guide” is set to “On”. See page 49.) Follow the steps in the Setup Guide and adjust the focus, height (angle) and picture size. After adjusting the focus, height (angle) and picture size, press ENTER to finish the Setup Guide.

  • Page 18: Setting Up The Projector

    Setting Up the Projector Video Setup If using this projector outside the U.S.A., please change setting to “0 IRE” in Video Setup. (See page 46.) Setting Up the Projector For optimal image quality, position the projector perpendicular to the screen with the projector's feet flat and level.

  • Page 19: Distance (Pg­lw3500/Pg­lw3000)

    Screen Size and Projection Distance Screen Note • Allow a margin of error in the values in the Lens center diagrams below. [PG-LW3000/PG-LW3500] 16:10 Signal Input (Normal Mode) Picture (Screen) size Projection distance [L] Distance from the lens center Diag. [ χ ] to the bottom of the image [H] Width Height...

  • Page 20: Distance (Pg­lx3500/Pg­lx3000)

    Screen Size and Projection Distance (Continued) Screen Note • Allow a margin of error in the values in the Lens center diagrams below. [PG-LX3000/PG-LX3500] 4:3 Signal Input (Normal Mode) Picture (Screen) size Projection distance [L] Distance from the lens center Diag.

  • Page 21: Projection (Prj) Mode

    [Menu item ➞ “Ceiling + Rear”] a Ceiling-Mount Setup It is recommended that you use the optional Sharp ceiling-mount adaptor and unit for this installation. Before mounting the projector, contact your nearest Sharp Authorized Projector Dealer or Service Center to obtain the recommended ceiling-mount adaptor and unit (sold...

  • Page 22: Connecting The Projector To Other Equipment

    • See page 67 “Compatibility Chart” for a list of computer signals compatible with the projector. Use with computer signals other than those listed may cause some of the functions to not work. • A Macintosh adaptor may be required for use with some Macintosh computers. Contact your nearest Macintosh Dealer. • Depending on the computer you are using, an image may not be projected unless the computer's external output port is switched on (e.g. Press “Fn” and “F5” keys simultaneously when using a SHARP notebook computer). Refer to the specific instructions in your computer's operation manual to enable your computer's external output port.
  • Page 23 Audio equipment ø3.5 mm ø3.5 mm stereo or mono audio cable AUDIO 1 (commercially available or available audio output as Sharp service part QCNWGA038WJPZ) terminal RCA audio RCA audio cable (commercially available) output AUDIO 2 terminal Cables for a camera or a video game...
  • Page 24 Amplifier ø3.5 mm stereo or mono audio cable ø3.5 mm (commercially available or available audio input as Sharp service part QCNWGA038WJPZ) terminal AUDIO OUT ø3.5 mm stereo minijack to RCA audio cable RCA audio (commercially available) input terminal Note • You can also use the MONITOR OUT terminal as the COMPUTER/COMPONENT 2 terminal. To use...

  • Page 25: Controlling The Projector By A Computer

    Controlling the Projector by a Computer When the RS-232C terminal on the projector is connected to a computer with an RS-232C serial control cable (cross type, commercially available), the computer can be used to control the projector and check the status of the projector. Refer to the “SETUP MANUAL” contained on the supplied CD-ROM for “RS-232C Specifications and Commands”.

  • Page 26: Connecting The Power Cord

    When connecting to the LAN terminal using a LAN cable LINK LED (green) Illuminates when linked. TX/RX LED (yellow) Illuminates when transmitting/receiving data. * To ensure safety, do not connect the LAN terminal with any cables that may cause excessive voltage such as a telephone line. Hub Computer To LAN terminal LAN cable (Category 5 type, commercially available) Note • When connecting to a hub, use a straight­through Category 5 (CAT.5) type cable (commercially available). • When connecting to a computer, use a cross­over Category 5 (CAT.5) type cable (commercially available). Connecting the Power Cord Plug the supplied power cord into the AC socket on the rear of the projector. Then plug into AC outlet.

  • Page 27: Turning The Projector On/Off

    Turning the Projector On/Off Info Turning the Projector On • When “Auto Restart” is set to “On”: If the power cord is unplugged from the outlet or the breaker switch is turned off when the Note that the connections to external projector is on, then the projector equipment and power outlet should be automatically turns on when the power cord done before performing the operations is plugged into the AC outlet or the breaker written below. (See pages to 22.) switch is turned on. (See page 50.) • English is the factory default language. If you...

  • Page 28: Image Projection

    Image Projection About the Setup Guide ENTER button After turning on the projector, the Setup Guide screen appears to assist you with projector setup. Guidance items Focus ring 1 FOCUS 2 HEIGHT ADJUST 3 ZOOM Press ENTER to exit the Setup Guide screen. Note • The Setup Guide screen automatically highlights the items in the following order: 1 FOCUS 2 HEIGHT ADJUST 4 ENTER...

  • Page 29: Adjusting The Height

    2 Adjusting the Height The height of the projector can be adjusted using the adjustment feet at the front and rear of the projector. When the screen is above the projector, the projection image can be made higher by adjusting the projector. Lift the projector to adjust its Make small height while lifting the HEIGHT...

  • Page 30: Correcting Trapezoidal Distortion

    Image Projection (Continued) Correcting Trapezoidal Distortion Adjustment buttons When the image is projected either from (P/R/O/Q) the top or from the bottom towards the screen at an angle, the image becomes distorted trapezoidally. The function for correcting trapezoidal distortion is called Keystone Correction.

  • Page 31: Switching The Input Mode

    VOL +/– (Volume) Switching the Input Mode buttons Select the appropriate Input mode for the INPUT buttons connected equipment. Press INPUT P/R to display the AV MUTE button INPUT list. Use INPUT P/R to select the Input mode. O/Q buttons When you select HDMI input, use O/Q to select the audio input terminal (HDMI or AUDIO).

  • Page 32: Resize Mode

    Image Projection (Continued) Resize Mode This function allows you to modify or customize the Resize mode to enhance the input image. Depending on the input signal, you can choose a desired image. Press RESIZE. • See page 47 for setting on menu screen. RESIZE button COMPUTER [PG-LW3000/PG-LW3500] NORMAL FULL NATIVE 16:9...
  • Page 33 VIDEO/DTV [PG-LW3000/PG-LW3500] Input signal Output screen image Video/DTV Image type NORMAL AREA ZOOM V-STRETCH 16:9 4:3 aspect ratio , 480P, , 576P, NTSC, PAL, SECAM Squeeze Letter box 16:9 aspect ratio 720P, 1035 1080 , 1080P 16:9 aspect ratio —*2 16:9 aspect ratio 540P 16:9 aspect ratio (4:3 aspect ratio in 16:9) : Cutout area on which images cannot be projected : Area on which the image is not included in the original signals *1 The Image Shift function can be used for these images. *2 Same as NORMAL mode.
  • Page 34 Image Projection (Continued) Resize Mode This function allows you to modify or customize the Resize mode to enhance the input image. Depending on the input signal, you can choose a desired image. Press RESIZE. RESIZE • See page 47 for setting on menu screen. button COMPUTER [PG-LX3000/PG-LX3500] Main resolution NORMAL FULL NATIVE...
  • Page 35 VIDEO/DTV [PG-LX3000/PG-LX3500] Input signal For 4:3 screen For 16:9 screen Video/DTV Image type NORMAL AREA ZOOM V-STRETCH BORDER 16:9 *1 *1 4:3 aspect ratio *1 *1 , 480P, , 576P, NTSC, PAL, SECAM Squeeze *1 *1 Letter box 720P, 1035 *1 1080 , 1080P 16:9 aspect ratio —*2 —*2...

  • Page 36: Operating With The Remote Control

    Operating with the Remote Control MAGNIFY buttons Displaying the Pointer FREEZE button PICTURE MODE button Press POINTER and press P/R/ O/Q on the remote control to AUTO SYNC button move the pointer. BREAK TIMER button • Press EFFECT to change the pointer icon SPOT button (5 types). Star Finger1 Finger2 Heart Underline Adjustment buttons (P/R/O/Q) EFFECT button Press POINTER again. ECO+QUIET button • The pointer will disappear.

  • Page 37: Auto Sync (Auto Sync Adjustment)

    Auto Sync Displaying an Enlarged (Auto Sync Adjustment) Portion of an Image Auto Sync function works when detecting Graphs, tables and other portions of input signal after the projector turns on. projected images can be enlarged. This is helpful when providing more detailed Press AUTO SYNC to manually adjust explanations.

  • Page 38: Menu Items

    Resolution sRGB Page Normal Contrast Resize Full Page Bright Native Area Zoom Color V-Stretch Border (PG-LX3000/LX3500) Tint 16:9 Keystone Sharp Page Blue Eco + Quiet [On/Off] Page Page English polski Language Deutsch Magyar Page Español Türkçe Nederlands CLR Temp Français...
  • Page 39 “Signal adjustment (SIG-ADJ)” menu “Screen adjustment (SCR-ADJ)” menu Main menu Sub menu Main menu Sub menu -150 +150 Resize SIG-ADJ Clock SCR - ADJ Normal Page Page Full Page Phase Native Image Shift Area Zoom H-Pos -150 +150 V-Stretch -40 ~ +40 (PG-LW3000/LW3500) V-Pos Border (PG-LX3000/LX3500) -96 ~ +96 (PG-LX3000/LX3500)
  • Page 40 Menu Items (Continued) “Projector adjustment (PRJ-ADJ1/2)” menu “Network” menu Main menu Sub menu Main menu PRJ-ADJ1 Auto Sync [On/Off] Network Password [Enable/Disable] Page Page Page Page Auto Power Off [On/Off] Page DHCP Client [On/Off] Page Auto Restart [On/Off] Page TCP/IP Page Speaker [On/Off] Page...

  • Page 41: Using The Menu Screen

    Using the Menu Screen Select from the Quick Start Menu, which is a collection of the most frequently used functions, or the Complete Menu, which enables advanced settings and adjustments. Adjustment buttons (P/R/O/Q) ENTER button MENU button MENU button ENTER button Adjustment buttons (P/R/O/Q) RETURN button • Press RETURN to return to the previous screen when the menu is displayed.

  • Page 42: Menu Selections (Complete Menu)

    Using the Menu Screen (Continued) Quick Start Menu The following items can be configured on the Quick Start Menu. Selectable items Description Input Search Start Automatically searches for and switches to the appropriate Input mode. Pressing an operation button during input searching cancels the search. Resolution Manually change the resolution. Use this function when the image and screen size do not match with the resolution selected automatically. (See page 45.) Resize Changes the Resize mode. Use this function to stretch the image vertically or horizontally or when the edges of the image cannot be seen. (See page 47.) Keystone Corrects the keystone distortion of projected images. Use this function to correct the trapezoidal distortion of images caused when projecting images at an angle to the screen. (See page 47.) Eco+Quiet When set to “On”, this function reduces the cooling fan noise and power consumption, thereby prolonging the operating life of the lamp. (See page 44.) Language Selects the language displayed on the screen. (See page 49.) Information Displays the input signal, lamp use time, remaining lamp life, etc.

  • Page 43: Press Menu

    Press P or R and select “Bright” Picture Picture PRJ1 PRJ2 to adjust. Picture Mode Picture Mode Standard Standard • The selected item is highlighted. Contrast Bright Blue CLR Temp BrilliantColor C.M.S. Setting C.M.S. Level 2 Eco+Quiet Reset SEL./ADJ. SEL./ADJ. Single ADJ Items to be adjusted PRJ1 PRJ2 Pict.

  • Page 44: Picture Adjustment ("Picture" Menu)

    PRJ2 Picture PRJ1 PRJ2 Picture Mode Standard Picture Mode Standard Contrast Bright CLR Temp Color BrilliantColor Tint C.M.S. Setting Sharp C.M.S. Film Mode Auto Blue Level 2 Eco+Quiet Reset SEL./ADJ. ENTER SEL./ADJ. ENTER 1 Selecting the Picture Mode The default settings of each item when selecting Picture Mode Selectable...

  • Page 45: Adjusting The Image

    C.M.S.­Hue Sets the hue of the main colors. Color* For less color For more color C.M.S.­Saturation Sets the saturation of the main intensity. intensity. colors Tint* For making skin For making skin C.M.S.­Value Sets the brightness of the main tones purplish. tones greenish. colors. Sharp* For less For more sharpness. sharpness. Reset The adjustments of “Hue”, Red* For weaker red. For stronger “Saturation” and “Value” of all red. colors are reset to the default Blue* For weaker For stronger setting. blue. blue. Return Returns to the “Picture” menu...

  • Page 46: Selecting The Film Mode

    Picture Adjustment (“Picture” Menu) (Continued) Menu operation n Page 5 Selecting the Film Mode 7 Eco+Quiet This function provides high-quality playback Selectable of images originally projected at 24 fps, such Brightness and Power consumption items as movies on DVDs. Approx. 65% Selectable Off 100%...

  • Page 47: Signal Adjustment ("Sig-Adj" Menu)

    Signal Adjustment (“SIG-ADJ” Menu) Menu operation n Page Pict. SIG-ADJ PRJ1 PRJ2 Clock Phase H-Pos V-Pos Reset Resolution 1024 x 768 Signal Type Auto Dynamic Range Standard Video System Auto Video Setup 0 IRE Signal Info 1024 x 768 48.3 kHz / V 60.0 SEL./ADJ.

  • Page 48: Setting The Video System

    Signal Adjustment (“SIG-ADJ” Menu) (Continued) Menu operation n Page 5 Setting the Video System 6 Setting the Video Setup The video input system mode is factory preset Selectable to “Auto”; however, a clear picture from the Description items connected audio-visual equipment may not be 0 IRE Sets the black level to 0 IRE.

  • Page 49: Adjusting The Projected Image ("Scr-Adj" Menu)

    Adjusting the Projected Image (“SCR-ADJ” Menu) Menu operation n Page Pict. SCR-ADJ PRJ1 PRJ2 Resize Normal Image Shift Keystone Overscan OSD Display Closed Caption Background Logo Setup Guide PRJ Mode Front Wall Color Language English SEL./ADJ. ENTER 1 Setting the Resize Mode 3 Keystone Correction Use this function to stretch the image When the image is projected either from the top...

  • Page 50: Setting The Overscan

    Adjusting the Projected Image (“SCR-ADJ” Menu) (Continued) Menu operation n Page 4 Setting the Overscan 6 Closed Caption This function allows you to set the overscan area <For Americas only> (display area). Info Selectable Description items • This function is available for NTSC3.58 signal. • This function does not work when the Resize The input area is displayed without the mode is set to “Border”. screen edges.

  • Page 51: Selecting The Background Image

    7 Selecting the Background 0 Selecting the Wall Color Image This function allows you to project the image to a colored surface or wall without using a Selectable items Description screen. Logo Sharp logo screen Selectable items Description Blue Blue screen The Wall Color function is not None — activated.

  • Page 52: Adjusting The Projector Function ("Prj-Adj1/2" Menu)

    Adjusting the Projector Function (“PRJ-ADJ1/2” Menu) Menu operation n Page Q PRJ­ADJ1 Q PRJ-ADJ2 Pict. PRJ1 PRJ-ADJ2 Net. Pict. PRJ-ADJ1 PRJ2 Quick Start Menu Auto Sync COMPUTER2 Select Monitor Output Auto Power Off FUNCTION Button Input Search Auto Restart STANDBY Mode Quick Start Speaker STANDBY Audio Out...

  • Page 53: System Lock Function

    • If you lose or forget your keycode, contact or on the projector as an individual your nearest Sharp Authorized Projector button, even if they share the same Dealer or Service Center (see page 71). Even button name.

  • Page 54: Keylock Function

    Adjusting the Projector Function (“PRJ-ADJ1/2” Menu) (Continued) Menu operation n Page 7 Keylock Function Info Use this function to lock the operation buttons • Even when Keylock function is set to “On”, on the projector. STANDBY/ON on the projector can be used This function can be set using either the menu to turn on and off the power. • Keylock cannot be set while the projector is: screen or ENTER on the projector. displaying the “Setup Guide” or “Menu”...

  • Page 55: Setting The Function Button Operation

    Menu operation n Page 0 Setting the FUNCTION ® Link Button Operation See “Using 3D Viewing Mode” on page details. You can assign one of the following functions to the FUNCTION button on the remote con- ® trol. The assigned function can be performed Link Invert by just pressing FUNCTION.

  • Page 56: Setting Up The Projector Network Environment ("Network" Menu)

    Setting Up the Projector Network Environment (“Network” Menu) Menu operation n Page Pict. PRJ1 PRJ2 Network Password Disable DHCP Client TCP/IP Reset Network Setting Restart Network X X X . X X X . X X X . X X X IP Address MAC Address X X : X X : X X : X X : X X : X X Projector...

  • Page 57: Dhcp Client Setting

    Menu operation n Page 2 DHCP Client Setting Selectable items Description IP Address Factory default setting: Connect the LAN cable before turning the 192.168.150.002 Enter an IP address projector on. If not, the DHCP Client function appropriate for the network. does not work. Subnet Mask Factory default setting: Selectable items Description 255.255.255.000 Set the subnet mask to the Obtains configuration same as that of the computer...

  • Page 58: Confirming The Projector Information

    Setting Up the Projector Network Environment (“Network” Menu) (Continued) Menu operation n Page 6 Confirming the Projector Information You can confirm the following items. Selectable Description items IP Address The IP address of the projector is displayed. MAC Address The MAC address of the projector is displayed. Projector The projector name is displayed. Link Displays the network connection status. Connected Connected to the network.

  • Page 59: Viewing Stereoscopic 3D Images

    Viewing Stereoscopic 3D Images Precautions on Viewing Stereoscopic 3D Images Before viewing stereoscopic 3D images, please read this section carefully. WARNING ■ Under normal conditions, viewing stereoscopic 3D images is safe for any duration that you would normally view your screen. However, some people may experience discomfort. The following precautions are recommended to minimize the potential for experiencing visual problems or any adverse symptoms.

  • Page 60: Information On The 3D Projection Function

    – For details on the supported signals, see the Compatibility Chart in this operation manual. 2) 3D LCD shutter glasses that support the DLP Link™* system ® – Contact your nearest Sharp Authorized Projector Dealer for purchasing details. * DLP Link™ is a trademark of Texas Instruments. ®...

  • Page 61: Using 3D Viewing Mode

    Viewing Stereoscopic 3D Images (Continued) Press 3D MODE on the remote control to display the 3D MODE Using 3D Viewing Mode menu. Info Use the following procedure to project 3D images. • If “An invalid button has been pressed.” is displayed, a 3D­compatible signal is For operation of the 3D LCD shutter not being input. Check the output signal glasses and the 3D-video playback on the playback equipment.

  • Page 62: Maintenance

    Maintenance Cleaning the projector Cleaning the lens ■ Ensure that you have unplugged the power ■ Use a commercially available blower or lens cord before cleaning the projector. cleaning paper (for glasses and camera ■ The cabinet as well as the operation panel is lenses) for cleaning the lens. Do not use any made of plastic. Avoid using benzene or liquid type cleaning agents, as they may thinner, as these can damage the finish on wear off the coating film on the surface of the the cabinet. lens. ■ Do not use volatile agents such as ■ As the surface of the lens can easily get insecticides on the projector. damaged, be careful not to scrape or hit the Do not attach rubber or plastic items to the lens. projector for long periods. The effects of some of the agents in the Caution plastic may cause damage to the quality or finish of the projector. • Do not use any glass cleaner to clean the lens. ■ Wipe off dirt gently with a soft flannel cloth. • Avoid touching the lens with your hands to Using a chemical cloth (wet/dry sheet type prevent fingerprints on or damage to the lens cloth, etc.) may deform the components of surface.

  • Page 63: Maintenance Indicators

    Maintenance Indicators ■ The warning lights (power indicator, lamp indicator and temperature warning indicator) on the projector indicate problems inside the projector. ■ If a problem occurs, either the temperature warning indicator or the lamp indicator will illuminate red, and the projector will enter Standby mode. After the projector has entered Standby mode, follow the procedures given below.
  • Page 64 • Temperatures • Use the projector in an warning (On)/ temperature is around the projector area with a temperature of indicator Red on abnormally high. are high. lower than 95°F (+35ºC). (Standby) • Blocked air intake • Relocate the projector to an area with proper ventilation. (See page 8.) • Cooling fan • Take the projector to your breakdown nearest Sharp Authorized • Internal circuit failure Projector Dealer or Service • Clogged air intake Center (see page 71) for repair. Lamp Green on Red on The lamp does • The lamp is shut • Disconnect the power cord indicator (Green not illuminate. down abnormally. from the AC outlet, and blinks then connect it again. when the Time to change • Remaining lamp life...

  • Page 65: Regarding The Lamp

    • Wait at least one hour after the power cord is disconnected to allow the surface of the lamp unit to fully cool before removing the lamp unit. ■ Carefully change the lamp by following the instructions described in this section. * If you wish, you may have the lamp replaced at your nearest Sharp Authorized Projector Dealer or Service Center. * If the new lamp does not light after replacement, take your projector to the nearest Sharp Authorized Projector Dealer or Service Center for repair.

  • Page 66: Removing And Installing The Lamp Unit

    Removing and Installing the Lamp Unit Warning! • Do not remove the lamp unit from the Optional Lamp unit projector right after use. The lamp and parts accessory AN­LX30LP around the lamp will be very hot and may cause burns or injury. Info • Do not touch the glass surface of the lamp unit or the inside of the projector. • To avoid injury to yourself and damage to the lamp, make sure you carefully follow the steps below. • Do not loosen other screws except for the lamp unit cover and lamp unit. STANDBY/ON button Press STANDBY/ON on the projector or STANDBY on the remote control to put the projector into Standby mode. Disconnect the power cord.

  • Page 67: Resetting The Lamp Timer

    Regarding the Lamp (Continued) Remove the lamp unit. Securing • Loosen the securing screw from the lamp screw unit. Hold the lamp unit and pull it in the direction of the arrow. At this time, keep the lamp unit horizontal and do not tilt it. Insert the new lamp unit. • Press the lamp unit firmly into the lamp unit compartment to align the lamp connectors. Fasten the securing screw. Replace the lamp unit cover. • Slide the lamp unit cover horizontally back into place and align the tabs (1). Then tighten the user service screw (2) to secure the lamp unit cover. Info • If the lamp unit and lamp unit cover are not correctly installed, the power will not turn on, even if the power cord is connected to the projector. Resetting the Lamp Timer Reset the lamp timer after replacing the lamp.

  • Page 68: Compatibility Chart

    Compatibility Chart Computer • Multiple signal support Pixel Clock: 12­165 MHz Horizontal Frequency: 15­110 kHz, Sync signal: Compatible with TTL level Vertical Frequency: 45­85 Hz, • Compatible with sync on green signal Display Horizontal frequency Analog Digital PC/MAC Mode Resolution Vertical frequency [Hz] [kHz] Support Support PG-LW3000/PG-LW3500 PG-LX3500/PG-LX3000 31.5 37.9 640 × 480 37.5 43.3 35.2 Upscale 37.9 SVGA 800 × 600 48.1 Upscale 46.9 53.7 48.4 56.5...
  • Page 69 3D Supported Signals Analog Digital Signal Horizontal Frequency (kHz) Vertical Frequency (Hz) Support Support 800 × 600 77.1 SVGA 1024 × 768 98.6 1280 × 720 92.6 WXGA * 2 120 * 1 1280 × 800 101.6 *1 Reduced Blanking *2 PG­LW3500/PG­LW3000 only Note • Your computer graphics card must be able to display 3D stereoscopic signals.

  • Page 70: Troubleshooting

    Troubleshooting Problem Check Page • Projector power cord is not plugged into the wall outlet. • Power to the external connected devices is off. – • The selected Input mode is wrong. • The AV Mute function is working. • Cables are incorrectly connected to the projector. 20–24 • Remote control battery has run out. No picture and no sound • External output has not been set when connecting a notebook computer. or projector does not • The lamp unit cover is not installed correctly. 64, 65 start. 20–24 • Cables are incorrectly connected to the projector. • “Bright” is set to minimum position. • Depending on the computer you are using, an image may not be – projected unless the signal output setting of the computer is switched to the external output. Refer to the computer's operation manual for how to switch its signal output settings. • Is “On” selected in “DLP Link ”? ® Sound is heard but no picture appears (or picture is dark). • Check that “Wall Color” is configured correctly. Dark or bluish image • Image adjustments are incorrectly set. • Make adjustments of “Color” and “Tint” in “Picture Mode” and lower the “BrilliantColor ” value. (Video Input only) • Video input system is incorrectly set.
  • Page 71 Problem Check Page • See “Maintenance Indicators”. Maintenance indicator on the projector illuminates or blinks in red. • Change the input signal type setting. Picture is green on COMPUTER (YPbPr)/ HDMI (YPbPr) Picture is pink (no green) on COMPUTER (RGB)/ HDMI (RGB) • Image adjustments are incorrectly set. Picture is too bright and whitish. 8, 9 • When temperature inside the projector increases, the cooling fan runs The cooling fan becomes faster. 60, 61, 62 noisy. • The lamp indicator is illuminating in red. 61, 64, 65 The lamp does not light Replace the lamp. up even after the projector turns on. The lamp suddenly turns off during projection. • Cables are incorrectly connected to the projector or the connected 20–24 The image sometimes equipment works improperly.
  • Page 72 Troubleshooting (Continued) Problem Check Page • Images may appear to flicker when fluorescent light or ambient light – 3D images flicker when enters your vision. watching in a room. – Turn off the lights. – Block any ambient light. • Check that you are using 3D LCD shutter glasses that support the – Ghosting (a double image) Link™ system. ® occurs without the image – Be sure to use 3D LCD shutter glasses that support the DLP Link™ ® appearing in 3D. system. • Check that the shutters on the 3D LCD shutter glasses are working – properly. – Turn the 3D LCD shutter glasses off and then on again. – Check the batteries of the 3D LCD shutter glasses. – Check that the 3D LCD shutter glasses are set to 3D viewing mode. Some 3D LCD shutter glasses are equipped with a special viewing mode (such as “dual view mode”) in addition to the normal 3D viewing mode. See the operation manual of your 3D LCD shutter glasses. • Check the settings of the projector. –...

  • Page 73: For Sharp Assistance

    If you encounter any problems during setup or operation of this projector, first refer to the “Troubleshooting” section on pages to 70. If this operation manual does not answer your question, please contact the SHARP Service departments listed below. U.S.A.

  • Page 74: Specifications

    Weight (approx.) 5.7lbs. (2.6kg) 5.5lbs. (2.5kg) 5.7lbs. (2.6kg) 5.5lbs. (2.5kg) As a part of policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement without prior notice. The performance specification figures indicated are nominal values of production units. There may be some deviations from these values in individual units.

  • Page 75: Dimensions

    Dimensions Units: inches (mm) (307) (80) (43.5) (31.5) M4 M4 (129) (126) • Screw hole specs: 75 mm × 104 mm • Depth of mounting holes: 8 mm • Standard screw: M4 (pitch 0.7 mm) • Quantity: 3...

  • Page 76: Index

    Screen Size and Projection Distance ·······························17 Contrast ············································································43 Security bar ······································································10 Setup Guide ·······························································26, 49 ® Link ······································································59 ® Sharp ················································································43 Link Invert ····························································59 SIG-ADJ ···········································································45 DNR ··················································································45 Signal Info ·········································································46 Dynamic Range ································································46 Signal Type ·······································································45 Eco+Quiet ···································································34, 44 Speaker ············································································50...

This manual is also suitable for:

Pg-lw3500Pg-lx3500Pg-lx3000

Table of Contents