Integra DPC-5.1 Instruction Manual page 23

Here are a few programming examples:
Chapters 25 and 12 of Title # 2 on disc #3 (two steps):
Disc number
Memory 1
3
Memory 2
All chapters of Title #1 on disc #1:
Disc number Title number
Memory 3
1
Chapter 2 of Title #4 on disc #1:
Memory 4
MEMORY
D T C D T C
1 3 02 25 8 – – – – –
3 02 12 – – – – –
2 9
–
3 1 01 – – 10 – – – –
1 04 02 – – – – –
4 11
– – – – – – – – – –
5 12
6 – – – – – 13 – – – – –
7 – – – – – 14 – – – – –
"Copy" the settings of the previous memory:
Doing so allows you to use the settings of the previous
memory as a starting point and only change one entry.
Example: if memory 1 refers to disc 3/Title 2/Chapter 25,
while memory 2 needs to refer to disc 3/Title 2/Chapter
12, you can "copy" memory 1 to memory 2 and modify
the "C" (chapter) entry:
• Program the memory to be copied (example:
memory 1), and press the ENTER button. The DVD
Changer advances to memory 2.
• Use the numeric buttons to enter the chapter num-
ber 12 on the black cursor on the "C" entry, then
press the ENTER button, "D" and "T" on the memory 1
are copied to memory 2.
Title number Chapter number
ENTER
2 2 5
ENTER
1
2
ENTER
1
ENTER
4
2
D T C D T C
15 – – – – – 22 – – – – –
– – – – – – – – – –
16 23
–
17 – – – – – 24 – – – –
– – – – – – – – – –
18 25
– – – – – – – – – –
19 26
–
20 – – – – – 27 – – – –
21 – – – – – 28 – – – – –
Other Memory Functi o ns
Leaving the MEMORY display page
To leave the MEMORY display page, press the MEMORY
button.
Correcting an entry of a previously programmed step:
a) Use the / buttons to move the cursor to the
corresponding memory number.
b) Select the entry (D, T or C) you wish to change with
the / buttons.
c) Enter the correct value using the numeric buttons.
Erasing a step
a) Stop playback.
b) If the Memory sequence is not currently displayed,
press the MEMORY button to select it.
c) Select the step you wish to erase with the
buttons.
d) Press the CLEAR button to erase the selected step.
Erasing the entire Memory sequence
To erase all steps, either switch the DVD Changer off and
back on again, or open and close the disc tray.
Programming the next step during playback
If you press the MEMORY button during playback, a
menu page is displayed where you can program a new
step.
Programming several new steps during playback
a) Press the MEMORY button followed by the DISPLAY
button.
The Memory menu appears on the TV screen.
b) Continue with step 3 on page 22.
N o t e s :
• Some discs do not allow Memory playback.
• The Repeat function (see page 21) is also available during
playback of your Memory sequence. Press the REPEAT button
to activate it for the curr e nt step of your Memory sequence.
• You can only program Title (or Track) and Chapter numbers
that exist on the selected disc.
• For Video and audio CDs, the "T" entry allows you to select
the track, while the "C" entry is not used.
• The Memory function is also available during playback.
DVD
VCD CD
/
23