9 • Assembling the Remote Control and use a solid-state speed control with this fan. Use only Hunter speed Mounting the Cradle . . . . . . . . . . . . . . 15 controls.
Page 3
If you want to use an existing fan site, complete the following checklist to System determine if the site is acceptable and safe for your new Hunter fan. If you cannot check off every item, prepare a new fan site as described on this page.
Page 4
ANSI/NFPA 70. If your ceiling fan, go to your fan manual and continue with Section 2 • Installing the you are unfamiliar with wiring, use a Ceiling Plate. qualified electrician. 42686-01 • 05/24/11 • Hunter Fan Company...
Page 5
Support Brace Hunter’s patented 3-position mounting system provides you maximum installation flexibility and ease. You can install your Hunter fan in one of three ways, depending on ceiling height and your preference: Low Profile, Standard, or Angled mounting. The steps in this manual include Ceiling instructions for all three Installer’s Choice mounting methods.
• Drill holes for and install wood screws. • Identify and connect electrical wires. • Lift 40 pounds. If you need help installing the fan, your Hunter fan dealer can direct you to a licensed installer or electrician. Gathering the Tools You will need the following tools for installing the fan: •...
Tighten the screws into the 9/64” pilot holes; do not use lubricants on the screws. Do not over tighten. Ceiling Plate Flat Washer 3” Wood Steps 2-3 – 2-6 Screw 42686-01 • 05/24/11 • Hunter Fan Company...
Adapter 3-7. Raise the fan and align the slots in the canopy with the hooks on the ceiling plate. Low Profile Washer 3-8. Place the slots over the hooks to hang the fan. 42686-01 • 05/24/11 • Hunter Fan Company...
The speed of the fan should only be changed by the Hunter control. Set the ceiling fan light kit to the ON position before installation. The light level should only be changed by the Hunter control.
5-7. Position the receiver in the canopy so that the antenna is close to the edge of the ceiling plate for clear reception. 42686-01 • 05/24/11 • Hunter Fan Company...
Note: Should you need to remove the trim ring, press firmly on Canopy opposite sides of the trim ring directly above the groove in the Trim hanger ball. The tabs will flex out releasing the canopy trim ring. Ring Canopy Screw 42686-01 • 05/24/11 • Hunter Fan Company...
7 • Assembling the Blades Hunter fans use several styles of fan blade irons (brackets that hold the blade to the fan). 7-1. Your fan may include blade grommets. If your fan has grommets, Step 7-1 (Detail) insert them by hand into the holes on the blades.
Align the side screw holes in the upper and lower switch housings. Attach the lower switch housing to the upper switch Lower housing with three #6-32 x 3/8” housing assembly screws. Switch Housing Housing Assembly Screw Step 8-4 Plug Connector Detail 42686-01 • 05/24/11 • Hunter Fan Company...
Thumbscrews Exceeding the wattage limit marked on the MAX wattage sticker affixed to the light socket(s) may result in fire hazard or improper operation. Steps 8-7 – 8-8 42686-01 • 05/24/11 • Hunter Fan Company...
Wall anchors and 6-32 x 1” screws may be used in situations where mounting to a stud is not possible. Use the inner mounting holes. Step 9-2 Removed Tabs Step 9-2 (Rocker Light Switch) 42686-01 • 05/24/11 • Hunter Fan Company...
10-6. You can mount the remote holder to any toggle switch plate with the screws already in the switch plate. Or, you can simply mount the remote holder on the wall. Steps 10-1 – 10-5 Step 10-6 Step 10-5 42686-01 • 05/24/11 • Hunter Fan Company...
If you need parts or service assistance, please call 888-830-1326 (In Canada, call 1-866-268-1936) or visit us at our Web site at http://www.hunterfan.com. Hunter Fan Company 7130 Goodlett Farms Pkwy #400 Memphis, Tennessee 38016 42686-01 • 05/24/11 • Hunter Fan Company...