Carton Inventory; Site Preparation; Operation Preparation - Chamberlain LiftMaster Professional BG770 Owner's Manual

CARTON INVENTORY

1. Unpack the carton, checking for possible damage during
shipping. The arm (when provided) is packed separately.
Damage claims MUST be filed with the freight carrier.
2. Check that the nameplate data (inside service cover) accurately
matches the operator that was ordered.
3. Verify that the following parts are included with the standard
unit.
MODEL BG770 PACKING LIST
PART NUMBER DESCRIPTION
02-102 Open/Close Push Button
07-8007 Gate Arm Hub
10-8007M Gate Bracket
80-G0187 Key, 1/2 x 1/2 x 1-3/8
82-NH38-06 Cone Point Set Screw, 3/8-16 x 3/8
82-HN50-25 Hex Bolt, 1/2-13 x 2-1/4
82-RH-50 Hex Nut, 1/2-13
85-LS-50 Split Lock Washer, 1/2
01-G0674 Owner's Manual

SITE PREPARATION

1. Be sure that selected gate location has required clearance for
arm movement (and counterweights on model BG790). Refer to
the dimensional drawings on page 3.
2. Run electrical power to the site according to local electrical
codes (Figure 1). See chart on page 7 for correct wire size and
length of run. If the wire gauge is too high (wire too small) or
the run is too long, the gate may not run properly or may not
run at all. Damage to components may result.
IMPORTANT NOTE: Be sure that the available power is the proper
voltage, phase, frequency, and amperage to supply the gate.
Refer to gate nameplate located inside the service cover.
3. Select locations for control equipment and run any control
wiring that may be needed (such as loop wires, card readers,
ticket spitters, pushbuttons, etc.).
OPERATOR PREPARATION
1. Remove the wood base from the unit and discard.
2. Locate the keys for the access panel (taped to the arm
mounting flange) and remove.
3. Open the side access panel and check the position of the power
ON/OFF switch.
4. Open the cover of the electrical cabinet and be sure that the
AUTO/MANUAL switch is in the "AUTO" position.
5. OPTIONAL CONTROL EQUIPMENT: If loop detectors, radio
controls, or other control equipment will be added at the site,
do so now. Refer to the instructions in this manual for
installation of factory-provided optional open and/or hold open
loop detectors and for connection of factory-provided optional
radio controls (see Optional Accessories on page 12).
P R E P A R A T I O N S
To reduce the risk of SEVERE INJURY or DEATH, disconnect
power BEFORE performing ANY adjustments.
QTY PART NUMBER DESCRIPTION
02-102
1
07-8007
1
10-8055
1
80-G0135
1
80-G0187
2
82-HN50-25
4
82-HN50-28
4
82-NH38-06
4
84-RH-50
1
84-WH-38
85-FW-38
85-FW-50
85-LS-50
01-G0674
Figure 1
5
WARNING
MODEL BG790 PACKING LIST
Open/Close Push Button
Arm Hub
Counter Weight Clamp
Threaded Rod, 3/8-16 x 18
Key, 1/2 x 1/2 x 1-3/8
Hex Head Bolt, 1/2-13 x 2-1/4
Hex Head Bolt, 1/2-13 x 3
Cone Point Set Screw, 3/8-16 x 3/8
Hex Nut, 1/2-13
Serrated Flange Nut, 3/8-16
Flat Washer, 3/8
Flat Washer, 1/2
Split Lock Washer, 1/2
Owner's Manual
NOTE: Install line power here. Do not
install line power in panel shown below.
Power switch should be in the OFF position.
AUTO/MANUAL switch should
be in the "AUTO" position.
QTY
1
2
2
2
2
12
2
4
14
8
8
8
16
1