9 • Troubleshooting . . . . . . . . . . . . . . . . . . . . 16 use a solid-state speed control with this fan. Use only Hunter speed controls.
Page 3
If you want to use an existing fan site, complete the following checklist to System determine if the site is acceptable and safe for your new Hunter fan. If you cannot check off every item, prepare a new fan site as described on this page.
Page 4
ANSI/NFPA 70. If your ceiling fan, go to your fan manual and continue with Section 2 • Installing the you are unfamiliar with wiring, use a Ceiling Plate. qualified electrician. 45037-01 • 06/06/11 • Hunter Fan Company...
Page 5
Support Brace Hunter’s patented 3-position mounting system provides you maximum installation flexibility and ease. You can install your Hunter fan in one of three ways, depending on ceiling height and your preference: Low Profile, Standard, or Angled mounting. The steps in this manual include Ceiling instructions for all three Installer’s Choice mounting methods.
• Drill holes for and install wood screws. • Identify and connect electrical wires. • Lift 40 pounds. If you need help installing the fan, your Hunter fan dealer can direct you to a licensed installer or electrician. Gathering the Tools You will need the following tools for installing the fan: •...
Tighten the screws into the 9/64” pilot holes; do not use lubricants on the screws. Do not over tighten. Flat Washer Steps 2-2 – 2-4 Ceiling Peak Ceiling Peak Large Large Opening Opening 3” Screw LEFT RIGHT Step 2-3 (Angled Ceiling Only) 45037-01 • 06/06/11 • Hunter Fan Company...
(Rotate the fan until you hear the notch pop into place.) Steps 3-4 – 3-5 Go to 4 • Wiring the Fan . WARNING: Fan may fall if not assembled as directed in these installation instructions. 45037-01 • 06/06/11 • Hunter Fan Company...
Page 9
WARNING: Fan may fall if not assembled as directed in these installation instructions. Steps 3-8 – 3-9 Low Profile Washer Step 3-7 (Detail) Low Profile Washer Adapter Canopy Trim Ring #8-32 x 3/4” Screw Step 3-10 45037-01 • 06/06/11 • Hunter Fan Company...
4-7. Spread the wires apart, with the grounded wires on one side of the outlet box and the ungrounded wires on the other side of the outlet box. 45037-01 • 06/06/11 • Hunter Fan Company...
5-6. Twist canopy trim ring clockwise to secure the canopy. Should you need to remove the canopy trim ring, follow these steps: 1. Twist canopy trim ring counter clockwise until it releases from canopy. Step 5-3 Step 5-4 Canopy Step 5-5 Screw 45037-01 • 06/06/11 • Hunter Fan Company...
6 • Assembling the Blades Hunter fans use several styles of fan blade irons (brackets that hold the Step 6-1 (Detail) blade to the fan). 6-1. Your fan may include blade grommets. If your fan has grommets, insert them by hand into the holes on the blades.
Failure to properly attach and Steps 7-1 – 7-4 tighten all three assembly screws could result in the switch housing Housing fixture falling. Upper Assembly Switch Screw Housing Plug Connector Lower Switch Housing Housing Assembly Screw 45037-01 • 06/06/11 • Hunter Fan Company...
Page 14
7-8. Screw the locking ring onto the light bulb socket. Housing 7-9. Repeat the above steps for the remaining light bulb sockets. 7-10. Install three 14W CFL light bulbs Housing Assembly Screw Plug Connector Detail 45037-01 • 06/06/11 • Hunter Fan Company...
If you need parts or service assistance, please call 888-830-1326 (In Canada, call 866-268-1936) or visit us at our Web site at http://www.hunterfan.com. Hunter Fan Company 7130 Goodlett Farms Parkway #400 Memphis, Tennessee 38016 45037-01 • 06/06/11 • Hunter Fan Company...