Oki CX3535MFP Material Safety Data Sheet

Material Safety Data Sheet
# 58409401
Black Toner, Type D2: P/N 44947308
For more information, contact Oki Data at: 2000
Bishops Gate Boulevard, Mount Laurel, NJ 08054-
4620.
Emergency Information: call 1-800-654-3282; US and
Canada only.
COMPOSITION/INFORMATION ON
INGREDIENTS
INGREDIENT(S)
Polyester resin
Carbon black
Wax
Amorphous Silica
Titanium dioxide 13463-67-7
HAZARDS IDENTIFICATION
Emergency Overview: If used as intended, the product does
not present acute or chronic health hazard.
Physical Hazards: This product is not classified as
flammable or combustible. It will burn in case of fire. Avoid
contact with strong oxidizers such as chromate, bromate and
nitrates.
Routes of Exposure: Inhalation, dermal contact, incidental
ingestion
Inhalation: Excessive inhalation may cause irritation of the
nose, throat and respiratory tract.
Eye Contact: Non-irritant.
Dermal Contact: Non-irritant, non-sensitiser.
Ingestion: Not currently known.
Chronic Effects: See Section 11 Supplemental Health
Information.
Carcinogenicity: See Section 11 Supplemental Health
Information.
Reproductive/Developmental: Not identified.
Target Organs: Prolonged breathing of high concentrations
may cause adverse effects on the respiratory system.
Signs and Symptoms of Exposure: Prolonged exposure to
dusts of this product may irritate the respiratory system.
Medical Conditions Aggravated by Exposure to This
Product: Respiratory disorders, such as asthma, may be
aggravated by prolonged exposure to high concentrations of
this product.
FIRST AID MEASURES
Eye Contact: Immediately flush eyes with plenty of water for
at least 15 minutes. If irritation persists, call a physician.
Skin Contact: Wash with soap and water. Wash clothing
before reuse. If irritation occurs or is persistent, seek medical
attention.
Ingestion: Dilute stomach contents with several glasses of
water.
Inhalation: Remove from exposure area to fresh air
immediately. Contact a physician if there is any difficulty in
breathing or other signs of distress.
FIRE FIGHTING MEASURES
General Hazard: Product will burn in case of fire.
Flash Point: Not applicable
Flammable Limits: Not applicable
Autoignition Temperature: Not applicable
Flammability classification: Not applicable
Extinguishing Media: Foam, halon, carbon dioxide, dry
chemical & water fog.
CAS No. wt.%
- - - 80-90
1333-86-4 3-8
- - - <10
7631-86-9 <5
<2
- - - TRADE SECRET
Unusual Fire & Explosion Hazard: Combustible powder.
Dust of this product at sufficient concentrations can form
explosive mixtures with air.
Fire Fighting Procedures: None
Hazardous Combustion Products: Carbon monoxide,
carbon dioxide and smoke.
ACCIDENTAL RELEASE MEASURES
Spills or Leaks: Vacuum-clean spilled toner and carefully
transfer into sealable waste container. If no vacuum-cleaner
is available, sweep slowly to minimize generation of dust
during clean-up. Residue can be removed with soap and cold
water.

HANDLING AND STORAGE

Handling: Avoid dust, keep away from ignition sources.
Prevention of Fire and Explosion: This material is capable
of creating a dust explosion. Keep away from heat, sparks &
flame.
Storage: Keep container in cool and dry area.
Hygienic Practices: Avoid inhalation and ingestion. Avoid
getting in eyes, on skin or clothing. Wash hands thoroughly
after handling, and before eating, drinking, or smoking.
EXPOSURE CONTROLS/PERSONAL
PROTECTION
Exposure Limits
OSHA PELs (TWA)
as the product: 15mg/m3 (Total dust) 5mg/m3 (Respirable
fraction)
Carbon black: 3.5 mg/m3
Other substances: Not listed
ACGIH TLVs (TWA)
as the product: 10mg/m3 (Total dust) 3mg/m3 (Respirable
fraction)
Carbon black: 3.5 mg/m3
Other substances: Not listed
DFG-MAK (TWA)
as the product: 4mg/m3 (Inhalable fraction) 1.5mg/m3
(Respirable fraction)
All substances: Not listed
NOHSC (TWA)
All substances: Not listed
Engineering Controls: Maintain adequate ventilation.
Eye Protection: Not required under intended use.
Skin Protection: Not required under intended use.
Respiratory Protection: Not required under intended use.
PHYSICAL AND CHEMICAL PROPERTIES
Appearance: Fine solid powder
Color: Black
Scent: Odorless
Melting Point: 110 - 150 degree (Softening point)
Specific Gravity(H2O=1): 1.1 - 1.5
Vapor Pressure: Not applicable
Vapor Density (Air=1): Not applicable
Evaporation Rate: Not applicable
Solubility in Water: Negligible
pH Value: Not a water-based product, therefore not
applicable.
Explosive Properties: little possiblity in intended use.
According to Explosive Evaluation, can form explosive dust-air
mixtures when finely dispersed in air, like most finely grained
organic powders.
STABILITY AND REACTIVITY
Stability: Stable
Incompatibility: Not identified.
Hazardous Decomposition Products: Carbon monoxide
and carbon dioxide.
Hazardous Polymerization: Will not occur.
1 – English