Sign in today to find solutions:

Forgot your password?

Don't have an account? Sign up

 
OWNER`S MANUAL
DROLET EPA WOODSTOVES
HT-1600 & HT-2000
US ENVIRONMENTAL PROTECTION
AGENCY PHASE II CERTIFIED
WOODSTOVES
Vérified and tested following
ULC S627 et UL 1482 Standards by:
READ AND KEEP THIS MANUAL FOR REFERENCE
: STOVE BUILDER INTERNATIONAL INC.
Manufactured by
1700, Léon-Harmel, Québec (Québec) G1N 4R9
Tel : ( 418 ) 527-3060
Fax : ( 418 ) 527-4311
www.drolet.ca
45060A

Summary of Contents

  • Page 1

    OWNER`S MANUAL DROLET EPA WOODSTOVES HT-1600 & HT-2000 US ENVIRONMENTAL PROTECTION AGENCY PHASE II CERTIFIED WOODSTOVES Vérified and tested following ULC S627 et UL 1482 Standards by: READ AND KEEP THIS MANUAL FOR REFERENCE : STOVE BUILDER INTERNATIONAL INC. Manufactured by 1700, Léon-Harmel, Québec (Québec) G1N 4R9...

  • Page 2: Table Of Contents

    MAINTENANCE ... 26 GLASS ... 26 GASKETING ... 26 PAINT ... 26 DROLET LIMITED LIFETIME WARRANTY ... 27 REGISTER YOU WARRANTY ONLINE To receive full warranty coverage, you will need to show evidence of the date you purchased your stove. Keep your sales invoice.

  • Page 3: Introduction

    In the pages that follow, we will give you advice on wood heating and controlled combustion as well as technical specifications regarding installation, operation and maintenance of the model you have chosen.

  • Page 4: Technical Specifications

    TECHNICAL SPECIFICATIONS Combustion Type: Recommended Surface Heating Capacity : Efficiency : Average Emission: Colour : Flue Pipe Diameter : Chimney type : Minimum Chimney Height : Maximum Log Length : Dimensions Overall: On Pedestal Model : Combustion Chamber : Width x Depth : Door Opening : Width x Height : Pyroceram Glass Door :...

  • Page 5: Tips On Wood Heating

    The chimney is the engine that drives the wood-heating system. Use a chimney that is UL-listed, with an inner diameter to match the stove’s outlet collar (6” for all Drolet wood stoves); Try to run the chimney inside the building for as much length as you can. A tall and warm chimney will produce a good draft;...

  • Page 6: Assembly, Pedestal And Decorative Sidewall Installation

    Figure 1: HT-2000 Pedestal Installation : 1. Remove all bricks and insulations in the appliance. 2. Slowly, lay down the stove on his back. 3. Install legs or the pedestal with the supplied nuts and bolts. Stand up the stove and place it with the required clearances.

  • Page 7: Bricks And Insulation Installation (ht-1600)

    BRICKS AND INSULATION INSTALLATION (HT-1600) 1. Remove from the stove all bricks and insulation. 2. Install all side bricks (11 x 4 1/2" x 9" & 1 x 4 ½” x 8 3/16") as shown in drawing below. 3. Install the back bricks (6 x 4 1/2" x 9") 4.

  • Page 8: Brick And Insulation Installation (ht-2000)

    BRICK AND INSULATION INSTALLATION (HT-2000) The stove is normally supplied with secondary air tubes in position. To install the baffle bricks and white ceramic insulation, it’s necessary to remove the two front secondary air tubes. First place only one baffle brick and one white ceramic insulation. Use the same method to put the other baffle brick and insulation.

  • Page 9: Air Tubes Installation (ht-2000)

    AIR TUBES INSTALLATION (HT-2000): The secondary air tubes are painted different colours . The back tube is yellow, the middle on is red and the front is unpainted. Before installing, make sure the locating holes in the tubes (holes near one end of the tube) are on the left side. Insert one tube in the right side air channel and slide it to the right as much as possible.

  • Page 10: Door Adjustment

    DOOR ADJUSTMENT In order for your stove to operate properly, the door should be adjusted periodically to provide an air tight fit. To adjust: • Remove the lock pin (spring pin) by pulling and turning it using pliers ("wise grip") •...

  • Page 11: The Benefits Of Installing A Blower

    THE BENEFITS OF INSTALLING A BLOWER A blower can be installed at the back of your DROLET stove. This option is necessary if you wish to redistribute into a room the heat trapped at the back of your stove. By forcing hot air toward the front, the blower enables you to extend the radiation power of your stove.

  • Page 12: Installation, Positioning The Stove

    REQUIRED POSITIONING THE STOVE It is very important to position the wood stove as close as possible to the chimney, and in an area that will favour the most efficient heat distribution possible throughout the house. The stove must therefore be installed in the room where the most time is spent, and in the most spacious room possible.

  • Page 13: Floor Protector

    Your wood stove should be placed on a non-combustible surface. The floor protector should be under the stove, eighteen inches beyond the front and eight inches beyond each side of the fuel loading and ash removal opening. If there is a horizontal section of chimney connector, the floor protector should go under it and two inches beyond each side.

  • Page 14: Clearances

    CLEARANCES It is of utmost importance that the clearances to combustible material be scrupulously respected upon installation of the stove you have selected. Refer to the tables below : Figure 6: Clearances to combustibles CANADA Model HT-1600 15/12 HT-2000 19/10...

  • Page 15: Reduced Clearances

    3" (76 mm) between the top of the shield and the ceiling must be respected to allow vertical air circulation behind the shield. The shield must extend 20" (500 mm) above the stove top and 18" (450mm) to each side of the stove.

  • Page 16: Chimney

    CHIMNEY Your wood stove may be hooked up with a factory built or masonry chimney. If you are using a factory built chimney, it must comply with UL 103 or ULC S629 standards; therefore it must be a Type HT (2100°F). It is extremely important that it be installed according to the manufacturer's specifications.

  • Page 17: Chimney Connector (stove Pipe)

    The stove pipe must be made of aluminized or cold roll steel with a minimum thickness of 0.021" or 0.53 mm. It is strictly forbidden to use galvanized steel.

  • Page 18: Typical Installations

    TYPICAL INSTALLATIONS FACTORY BUILT CHIMNEY: 18" CLEARANCE Wall installation RAIN CAP ROOF FLASHING WALL RADIATION SHIELD WALL SUPPORT Vertical installation RADIATION SHIELD CEILING SUPPORT...

  • Page 19

    MASONRY CHIMNEY: C lay liner Thimb le C lean out door...

  • Page 20

    FACTORY BUILT THIMBLE:...

  • Page 21

    BRICK THIMBLE:...

  • Page 22: Woodstove Utilization

    IT IS EXTREMELY IMPORTANT THAT YOU USE DRY WOOD ONLY IN YOUR WOOD STOVE. The wood must have dried for 9 to 15 months, such that the humidity content (in weight) is reduced below 20% of the weight of the log. It is very important to keep in mind that even if the wood has been cut since one, two or even more years, it is not necessarily dry, if it has been stored in poor conditions;...

  • Page 23: Testing Your Wood, The First Fires, Ignition

    Make sure that there’s enough air circulation while curing the stove. The odours could be smelled during the 3 or 4 first fires. Never start your stove outside. You will not be able to see if you are over heating.

  • Page 24: Heating

    The air intake control on your stove is very simple. If you pull on it out completely towards you, it is fully open. If you push on it until it stops the combustion air is reduced to a minimum.

  • Page 25: Reloading, Creosote Formation And Need For Removal

    IS HAPPENING EADJUST THE AIR INTAKE CONTROL AT A LOWER SETTING • T HE INSTALLATION OF A LOG CRADLE IS NOT RECOMMENDED IN YOUR DROLET WOOD STOVE • N EVER PUT WOOD ABOVE THE FIREBRICK LINING OF THE FIREBOX CREOSOTE FORMATION AND NEED FOR REMOVAL When wood is burned slowly, it produces tar and other organic vapours, which combine with expelled moisture to form creosote.

  • Page 26: Ash Disposal

    ASH DISPOSAL Ashes should be removed from the stove every few days or when ashes get to 2 to 3 inches deep. Always empty the stove when it is cold, such as in the morning. Always dispose of ashes in a metal container with a tight fitting lid. Place this container on a non combustible floor or on the ground, well away from all combustible materials, pending final disposal.

  • Page 27: Maintenance, Glass, Gasketing, Paint

    Do not abuse the glass door by striking or slamming shut. Do not use the stove if the glass is broken. • If the glass on your stove breaks, replace only with glazing supplied from the Drolet dealer.

  • Page 28: Drolet Limited Lifetime Warranty

    Paint (peeling), gaskets, insulation, and ceramic glass (thermal breakage only*) *Pictures required Shall your unit or a components be defective, contact immediately your DROLET dealer. Prior to your call make sure you have the following information necessary to your warranty claim treatment: •...

  • Page 29

    Before shipping your unit or defective component to our plant, you must obtain from your DROLET dealer an Authorization Number. Any merchandise shipped to our plant without authorization will be refused automatically and returned to sender.

Comments to this Manuals

Symbols: 0

Latest comments:

×

Select the desired size and copy embed code

Copy your embed code and put on your site: