Table of Contents
Advertisement
Quick Links
Installation
Instructions
BEFORE YOU BEGIN
Read these instructions completely and
carefully.
IMPORTANT-
IMPORTANT-
Note to Installer -
Note to Customer -
TOOLS YOU
WILL NEED
SLIP JOINT PLIERS
FLAT BLADE SCREWDRIVER
PHILLIPS SCREWDRIVER
LEVEL
Questions on Installation? Call: 800.GE.CARES (US)
WARNING
NOTE: Installation and service of this dryer requires basic
mechanical and electrical skills. It is your responsibility to
contact a quali ed installer to make the electrical connections.
MATERIALS YOU WILL NEED
4" DIA. METAL DUCT
(RECOMMENDED)
4" DIA. FLEXIBLE METAL (SEMI-RIGID)
UL LISTED TRANSITION DUCT
(IF NEEDED)
KIT WX08X10077 (INCLUDES 2 ELBOWS)
4" DIA. FLEXIBLE METAL (FOIL TYPE)
UL LISTED TRANSITION DUCT
(IF NEEDED.)
www.GEAppliances.com (US)
RISK OF FIRE
4" DUCT
4" DIA. METAL
CLAMPS (2)
ELBOW
OR
4" SPRING
CLAMPS (2)
DUCT TAPE
4" COVER PLATE (IF NEEDED
(KIT WE1M454)
234D1582P006 31-16674 03-12 GE
Electric Dryer
06
SAFETY
DRYER POWER
EXHAUST
GLASSES
HOOD
(NOT PROVIDED
UL RATED
120/240V,30A
WITH 3 OR 4 PRONGS.
IDENTIFY THE PLUG
3/4" STRAIN
TYPE AS PER THE
RELIEF
GLOVES
HOUSE RECEPTACLE
UL RECOGNIZED
BEFORE PURCHASING
LINE CORD.
CORD KIT
WITH DRYER)
Advertisement
Table of Contents
Related Manuals for GE DNCD450EGWC
Summary of Contents for GE DNCD450EGWC
-
Page 1: Electric Dryer
Installation Electric Dryer Instructions Questions on Installation? Call: 800.GE.CARES (US) www.GEAppliances.com (US) BEFORE YOU BEGIN WARNING RISK OF FIRE Read these instructions completely and carefully. IMPORTANT- IMPORTANT- Note to Installer - Note to Customer - NOTE: Installation and service of this dryer requires basic mechanical and electrical skills. -
Page 2: Mobile Home Installation
Installation Instructions Minimum Clearance Other Than Alcove or Closet Installation must CONNECTING DRYER USING 4-WIRE PREPARING FOR INSTALLATION CONNECTION (MUST BE USED FOR OF NEW DRYER MOBILE HOME INSTALLATION) TIP: Install your dryer before installing your washer. NOTE: Since January 1,1996, the National Electric code This will allow better access when installing dryer exhaust. -
Page 3: Exhaust Information
Installation Instructions CONNECTING DRYER USING 3-WIRE EXHAUST INFORMATION CONNECTION WARNING - IN CANADA AND IN THE IF REQUIRED, BY LOCAL CODE, UNITED STATES, THE REQUIRED EXHAUST INSTALL EXTERNAL GROUND (NOT PROVIDED) TO GROUNDED DUCT DIAMETER IS 4 in (102mm). DO NOT USE METAL, COLD WATER PIPE, OR GREEN GROUND... -
Page 4: Exhaust Connection
Installation Instructions STANDARD REAR EXHAUST SEALING OF JOINTS (Vented at oor level) For straight line installation, connect the dryer exhaust to the external exhaust hood using duct tape or clamp. EXTERNAL DUCT OPENING INSULATION DUCT TAPE OR DUCT CLAMP 4" METAL DUCT CUT TO PROPER LENGTH EXHAUST CONNECTION DUCT TAPE OR... -
Page 5: Alcove Or Closet Installation
Installation Instructions For best drying performance UL-LISTED FLEXIBLE METAL (FOIL-TYPE) TRANSITION DUCT LEVELING AND STABILIZING YOUR DRYER ELBOW HIGHLY RECOMMENDED ELBOWS HIGHLY RECOMMENDED ALCOVE OR CLOSET INSTALLATION DON’T MUST DO NOT EXHAUST INFORMATION SIT DRYER ON FLEXIBLE EXHAUST. DO NOT USE EXCESSIVE EXHAUST LENGTH... - Page 6 Installation Instructions BATHROOM OR BEDROOM INSTALLATION FIXING HOLE 9" Cut the duct as shown and keep portion A. TAB LOCATION MOBILE OR MANUFACTURED HOME INSTALLATION BEND TAB UP 45 Through the rear opening, locate the tab in the middle of the appliance base.
- Page 7 Installation Instructions ADDING ELBOW AND DUCT FOR ADDING COVER PLATE TO REAR OF EXHAUST TO LEFT OR RIGHT SIDE OF CABINET (SIDES AND BOTTOM EXHAUST) CABINET CAUTION: Be sure not to pull or damage the electrical wires inside the dryer when inserting the duct. PL ATE (KIT WE1M454) EXHAUST CAN...
- Page 8 Installation Instructions SERVICING WARNING- LABEL ALL WIRES PRIOR TO DISCONNECTING WHEN SERVICING CONTROLS. WIRING ERRORS CAN CAUSE IMPROPER AND REMOVE THE BOTTOM SCREW LOOSEN THE TOP SCREWS FROM EACH FROM EACH HINGE ON THE HINGE ON THE DRYER FACE HALF WAY. DANGEROUS OPERATION AFTER DRYER FACE.