Table of Contents
Advertisement
Quick Links
DM 2610938876 03-06.qxd
3/17/06
9:21 AM
Page 1
300 Series
Instructional Safety
High Speed Rotary Tool
Manual
03-5415317
http://www.dremel.com
Dremel brand products are manufactured and sold by the
Dremel Division of Robert Bosch Tool Corporation
Form No. 2610938876 03/06
Robert Bosch Tool Corporation © 2004
All Rights Reserved
Advertisement
Table of Contents
Related Manuals for Dremel 03-5415317
Summary of Contents for Dremel 03-5415317
- Page 1 300 Series Instructional Safety High Speed Rotary Tool Manual 03-5415317 http://www.dremel.com Dremel brand products are manufactured and sold by the Dremel Division of Robert Bosch Tool Corporation Form No. 2610938876 03/06 Robert Bosch Tool Corporation © 2004 All Rights Reserved...
-
Page 2: General Safety Rules
DM 2610938876 03-06.qxd Read all instructions. Failure to follow all instructions listed below WARNING may result in electric shock, fire and/or serious injury. The term “power tool” in all of the warnings listed below refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool. - Page 3 DM 2610938876 03-06.qxd Keep handles dry, clean and free from oil and grease. Slippery hands cannot safely control the power tool. Power tool use and care Do not force the power tool. Use the cor- rect power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.
- Page 4 DM 2610938876 03-06.qxd SAFETY RULES FOR ROTARY TOOL (CONTINUED) sories. You may unexpectedly cause the tool to start leading to serious personal injury. Be aware of the switch location, when placing the tool down or when picking the tool up. You may accidentally activate the switch.
- Page 5 DM 2610938876 03-06.qxd SAFETY RULES FOR ROTARY TOOL (CONTINUED) Do not allow familiarity gained from fre- quent use of your rotary tool to become commonplace. Always remember that a careless fraction of a second is sufficient to inflict severe injury. Do not alter or misuse tool.
- Page 6 Thus, the success you will experience with your Dremel rotary tool system – rotary tool, accessories and attachments; unlimited versatility for you and your projects no matter where you are.
-
Page 7: Specifications
DM 2610938876 03-06.qxd General Specifications Voltage Rating ..230-240 V Amperage Rating ....1.15 A No Load Speed ..N o 10,000-37,000/min Collet Capacity . - Page 8 DM 2610938876 03-06.qxd Some of the following symbols may be used on your tool. Please study IMPORTANT! them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and safer. Symbol Name Volts Amperes Hertz Watt...
- Page 9 Always unplug rotary tool before changing accessories, changing WARNING collets, or servicing the tool. Collets The Dremel™ accessories available for the rotary tool come with various shank sizes. Four size collets are available to accommdate the different shank sizes. Collet sizes are identified by the rings on the back of the collet: •...
-
Page 10: Operation
Keep in mind that your rotary tool will perform best by allowing the speed, along with the correct Dremel™ accessory and attachment, to do the work for you. Do not put pressure on the tool during use, if possible. - Page 11 OPERATION (CONTINUED) Set the Speed Control to the desired setting. Some guidelines regarding tool speed: • There is no accessory for the Dremel Rotary tool that will drill or cut glass. • Plastic and other materials that melt at low temperatures should be cut at low speeds.
-
Page 12: Speed Settings
DM 2610938876 03-06.qxd Use only Dremel™ tested, high performance accessories. * Speed for light cuts; Caution - burning on deep grooves. • Depending on cutting direction relative to grain. Catalog Soft Number Wood Wood 100, 121, 131 114, 124, 134, 144... - Page 13 DM 2610938876 03-06.qxd SPEED SETTINGS (CONTINUED) Use only Dremel™ tested, high performance accessories. * Speed for light cuts; Caution - burning on deep grooves. • Depending on cutting direction relative to grain. Catalog Soft Number Wood Wood 612, 640 615, 617, 618,...
- Page 14 DM 2610938876 03-06.qxd SPEED SETTINGS (CONTINUED) Use only Dremel™ tested, high performance accessories. * Speed for light cuts; Caution - burning on deep grooves. Catalog Soft Number Wood Wood 409, 420, 426, 8-10 For use on drywall. For best results, use at 35,000 rpm.
-
Page 15: Maintenance
Using the tool with worn CAUTION brushes will permanently damage the motor. Use only original Dremel™ replacement brushes.’ Inspect the rotary tool brushes after 40-50 hours of use. If the rotary tool runs erratical- ly, loses power, or makes unusual noises check the brushes for wear and possible replacement. - Page 16 Ventilation openings and switch levers must be kept clean and free of foreign matter. Do not attempt to clean by inserting pointed objects through openings. There is no need to lubricate the Dremel™ rotary tool. CAUTION plastic parts. Some of these are: gasoline,...
- Page 17 For availability of all accessories and attachments, refer your local hardware, hobby or home center. Or contact Dremel Consumer Service at: Use only Dremel™, high-performance accessories. Other accessories are WARNING not designed for this tool and may lead to personal injury or property damage.
- Page 18 DM 2610938876 03-06.qxd High Speed Cutters High speed cutters are used in carving, cutting and slotting wood, plastics and soft metals (such as aluminum, copper and brass). Made of high quality steel. Structured Tooth Tungsten Carbide Cutters 1/8" shank These cutters feature fast cutting needle- sharp teeth for greater material removal with minimum loading.
- Page 19 Drum bands are replaceable and come in fine and coarse grades. The following attachments are part of the Dremel Rotary Tool System; increasing the versatility of your rotary tool. Ideal for hard-to-reach places and fine detail work.
- Page 20 DM 2610938876 03-06.qxd Grout Removal Fast and easy way to regrout any room or replace a broken tile! • Multiple side depth adjustment • 30° angle for control cutting • Guides 180° apart to keep bit centered between tiles • Easy screw mounting •...
- Page 21 Use with models: 275, 285, 395, 398, 770, 780, 800, 300 Series, 400 Series XPR. Flex Shaft Tool Holder Conveniently suspends any Dremel rotary tool above your work- bench. • Perfect for use with the Flex-Shaft attachment •...
-
Page 22: Service Parts & Diagram
DM 2610938876 03-06.qxd SERVICE PARTS & DIAGRAM Ref. Part No. Description 2615990962 Wrench 2615297355 Collet Nut 2615110480 1/8" Collet (In Tool) 2615919754 Nose Cap 2610912779 Armature and Bearing Assembly 2610907324 Field Assembly 2610913818 Shaft Lock Assembly 2610925724 Housing Set 2610925720 Hanger 3/17/06 9:21 AM... - Page 23 DM 2610938876 03-06.qxd 3/17/06 9:21 AM Page 23 NOTES:...
- Page 24 DREMEL Service Station, postal charges prepaid. DREMEL reserves the right to decline responsibility in case of repairs made by persons other than DREMEL service staff. In no event compensation can be claimed in case of damage to the workpiece or injury to the tool user.