Related Manuals for Directed Electronics Nissan
Summary of Contents for Directed Electronics Nissan
- Page 1 2 2 1 1 9 9 4 4 4 4 ➤ O O w w n n e e r r ’ ’ s s / / I I n n s s t t a a l l l l a a t t i i o o n n G G u u i i d d e e...
-
Page 3: L L I I M M I I T T E E D D L L I I F F E E T T I I M M E E C C O O N N S S U U M M E E R R W W A A R R R R A A N N T T Y Y
Directed Electronics (hereinafter "Directed") promises to the original purchaser to repair or replace with a comparable reconditioned Directed DIY keyless entry unit if this Directed DIY keyless entry unit (hereinafter "Unit"), excluding without limitation, any... - Page 4 This product warranty is automatically void if its date code or serial number is defaced, missing, or altered. This warranty will not be valid unless you have completed the war- ranty card and mailed it to Directed Electronics. within 10 days after purchase to the address listed on the warranty registration card.
-
Page 5: Table Of Contents
: : ....................4 4 1 1 © 2006 directed electronics... - Page 6 ➤ Drill ➤ Screwdrivers (Phillips and Flathead) ➤ Wire Stripper ➤ Solder Iron ➤ Pliers ➤ Crimping Tool note: The installation tools listed above may be optional and those required will vary depending on your vehicle. © 2006 directed electronics.
-
Page 7: System Maintenance
The system requires no specific maintenance. Your transmitter is powered by a miniature 3-volt battery (type CR2032) that will last approximately one year under normal use. When the battery begins to weaken, the operating range will be reduced. © 2006 directed electronics... -
Page 8: Fcc/Id Notice
(2) This device must accept any interference received, including interference that may cause undesirable operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this device. © 2006 directed electronics. -
Page 9: P P R R I I M M A A R R Y Y H H A A R R N N E E S S S S ( ( H H 1 1 ) ) , , 1 1 4 4 - - P P I I N N C C O O N N N N E E C C T T O O R
H1/5 VIOLET/BLACK is connected to H1/2 VIOLET and is fused (15A). note: H1/1 LIGHT GREEN/BLACK cle is equipped with a factory alarm disarm. © 2006 directed electronics Factory Alarm Disarm Unlock 87 Normally Open Unlock 30 Common-Output Unlock 87A Normally Closed... - Page 10 2. Connect the Black clip to a good chassis ground. 3. If a positive voltage source is probed, the Red LED will illuminate brightly. warning! Do not use this test probe on computerized equipment as damage can result. © 2006 directed electronics.
-
Page 11: C C O O D D E E H H O O P P P P I I N N G G ® ® R R E E - - S S Y Y N N C C H H R R O O N N I I Z Z E
8 8 0 0 0 0 - - 4 4 7 7 7 7 - - 1 1 3 3 8 8 2 2 (to get hours of phone operation) for live tech- nical assistance. © 2006 directed electronics warning! On vehicles with air bags or sup-... - Page 12 © 2006 directed electronics.
-
Page 13: Step 1
Almost all power and ignition wires can be found behind the key cylinder under the lower drivers side dash panel. Using the appropriate hand tools, remove the lower dash panel using care not to break any parts. If the panel does not come off easily © 2006 directed electronics... - Page 14 SRS underneath the steering column near the key cylinder. DO NOT tamper or unplug these for any reason to prevent costly damages to your vehicle or personal injury. Tampering may cause unintended deployment of airbags. © 2006 directed electronics.
-
Page 15: Step 3
RED lead of the LED tester to +12V and secure it. Probe the suspect wire. With the light switch in the off position the LED tester will not illuminate. While watching the © 2006 directed electronics... -
Page 16: Step 4 (Optional)
Refer to TechTips on www.readyremote.com or contact READY REMOTE technical Support for details and additional parts required. Refer to the end of this manual for the Emergency Override Procedure (if you lose your remote) to disable the optional starter © 2006 directed electronics. -
Page 17: Step 5
Once you have determined which type of factory door lock circuit you are working with, and the color codes of © 2006 directed electronics... - Page 18 Subarus, most Isuzus, and many Mazdas. Some mid-eighties Nissans, pre-1985 Mercedes-Benz and Audi. ■ T T y y p p e e E E : : Electrically-activated vacuum systems. The vehicle must have a vacuum actuator in each door. Make sure that lock- © 2006 directed electronics.
- Page 19 One-wire system - cut to lock, ground to unlock. This system is found in late-model Nissan Sentras, some Nissan 240SX, and Nissan 300ZX 1992 and later. It is also found in older Mitsubishis, and some early Mazda MPV’s. ■ T T y y p p e e G G : : Positive (+) multiplex.
- Page 20 451M. Almost all domestically-built Fords are Type C. Ford builds no type A systems. Chrysler builds both Type A and Type C, so proceed with caution. important: Remember that these wires’ functions reverse between Type A and Type B. © 2006 directed electronics.
- Page 21 © 2006 directed electronics...
- Page 22 B: negative-triggered, relay-driven system This system is common in many Toyota, Nissan, Honda, and Saturn models, as well as Fords with the keyless-entry system (some other Fords also use Type B). The switch will have three wires on it, and one wire will test ground all the time.
- Page 23 The lock or unlock wire is switched to (+)12V, while the other wire is still grounded, thus completing the circuit and powering the motor. This will disconnect the switch from the motor before supplying the motor with (+)12V, avoiding sending (+)12V directly to (-) ground. © 2006 directed electronics...
- Page 24 (+)12V supply for the door lock switch*, or direct- ly to the positive (+) battery post with a fuse at the battery post. Once both door lock wires are Connect the green/black wire to This wire must be connected to © 2006 directed electronics.
- Page 25 (+)12V supply for the door lock switch*, or directly to the positive (+) battery post with a fuse at the battery post. (See both notes above.) © 2006 directed electronics Connect the brown/black wire Connect the blue/black wire to the...
- Page 26 Adding door lock actuators can be complicated. Please contact READY REMOTE technical support prior to attempting the addition of actuators. © 2006 directed electronics.
- Page 27 The system must be programmed for 3.5-second door lock pulses, and the violet jumper between the #87 lock terminal and the #87 unlock terminal must be cut. Contact READY REMOTE technical support. See Programming section. © 2006 directed electronics...
- Page 28 This type of door lock system usually requires a negative pulse to unlock, and cutting the wire to lock the door. (With some vehi- cles, these are reversed.) It is found in the late-model Nissan Sentras, some Nissan 240SX, Nissan 300ZX 1992 and later. It is also found in some Mazda MPVs.
- Page 29 . . r r e e a a d d y y r r e e m m o o t t e e . . c c o o m m (On-Line Tech Support, Tech Tips) for complete resistor test procedure and additional information for multiplexed door locks. © 2006 directed electronics...
- Page 30 If the multimeter displays zero resis- tance in one direction, no resistor is needed for that direction. Once the resistor value(s) is determined, refer to the wiring dia- gram for proper wiring. © 2006 directed electronics.
- Page 31 Cut the output wire from the door lock switch/key cylinder in half. Test with the meter from the switch side of the cut door lock switch/key cylinder wire to a reliable ground source. Some good © 2006 directed electronics...
-
Page 32: Step 6
1 1 - - 8 8 0 0 0 0 - - 4 4 7 7 7 7 - - 1 1 3 3 8 8 2 2 for live technical assistance as spe- cial wiring and an additional relay is required. © 2006 directed electronics. - Page 33 When the correct wire has been found, solder the LIGHT GREEN/BLACK (H1/1) wire to the wire which activates in the unlock position when the key is turned. After this wire has been connected wrap the connection with electrical tape. © 2006 directed electronics...
-
Page 34: Step 7 (Optional)
If the on-line wiring information shows a 5-wire trunk release system, please contact READY REMOTE Technical Support for further instructions. button is pressed for 1.5 seconds the © 2006 directed electronics. -
Page 35: Step 8
Additional transmitters (part no. 26131) can be ordered by contacting your local dealer at 1-800-274-0200. Use the following to add a transmitter to the system. The following is the basic sequence of steps to remember whenever programming this unit: © 2006 directed electronics... - Page 36 2. K K e e y y . . Turn the ignition to the ON position. The parking lights will immediately turn on to indicate transmitter learn mode. After 5- seconds the parking lights will turn off and then turn back on to indicate ready to learn mode. button. Repeat © 2006 directed electronics.
- Page 37 If you still experience problems contact READY REMOTE Technical Support at 1 1 - - 8 8 0 0 0 0 - - 4 4 7 7 7 7 - - 1 1 3 3 8 8 2 2 . © 2006 directed electronics...
-
Page 38: Standard Configuration
The door locking function is controlled by pressing Button The door unlocking function is controlled by pressing Button This auxiliary output is used for trunk release/expansion add ons. Button This button is used to program the transmitter(s). © 2006 directed electronics. - Page 39 When the double pulse unlock feature is turned on, the H1/12 BLUE/BLACK wire will supply two pulses instead of a single pulse. This makes it possible to directly interface with double pulse vehicles without any extra parts. Uncut – single pulse Cut – double pulse © 2006 directed electronics...
-
Page 40: Locking With Transmitter
The doors will lock for one second. The parking © 2006 directed electronics. - Page 41 © 2006 directed electronics r r e e - - s s y y n n c c h h r r o o n n i i z z e e ®...
- Page 42 T T r r a a n n s s m m i i t t t t e e r r : : A hand-held, remote control that operates the various functions of the system. © 2006 directed electronics.
- Page 43 _________________________________________________ _________________________________________________ _________________________________________________ _________________________________________________ _________________________________________________ _________________________________________________ _________________________________________________ _________________________________________________ _________________________________________________ _________________________________________________ _________________________________________________ _________________________________________________ _________________________________________________ _________________________________________________ _________________________________________________ _________________________________________________ _________________________________________________ _________________________________________________ _________________________________________________ _________________________________________________ _________________________________________________ © 2006 directed electronics...
- Page 44 © 2006 directed electronics.
-
Page 45: Quick Reference Guide
QUICK REFERENCE GUIDE: To lock the doors using your transmitter ■ Pressing for one second will lock the doors. The doors will lock and the parking lights will flash once to confirm the doors are locked. To unlock the doors using your transmitter ■... - Page 48 The company behind this system is Directed Electronics Since its inception, Directed Electronics has had one purpose, to provide consumers with the finest vehicle security and car stereo products and accessories available. The recipient of nearly 100 patents and Innovations Awards in the field of advanced electronic technology, DIRECTED is ISO 9001 registered.