Electrical Connections; Preparing The Dishwasher For Installation - Asko 1325 Installation Instructions Manual

ELECTRICAL CONNECTIONS

ELECTRICAL CONNECTIONS ELECTRICAL CONNECTIONS ELECTRICAL CONNECTIONS ELECTRICAL CONNECTIONS
WARNING!
Before working on wiring for any
electrical appliance, be sure the electrical power
has been turned off at the breaker/fuse box.
WARNING!
D i s c o n n e c t e l e c t r i c a l p o w e r
supply and place a tag at the disconnect switch
indicating that you are working on the circuit.
WARNING!
E l e c t r i c a l
connections must comply with the applicable
portions of the national electrical code and/or
other local electrical codes.
The electrical supply must be a 110–120 volts, 15 or 20
amp properly grounded circuit. No other appliance or
outlets should be on this circuit.
GR GR GROUNDING INSTR GR GR OUNDING INSTRUCTIONS OUNDING INSTR OUNDING INSTR OUNDING INSTR
This unit must be grounded to operate properly. It must
be connected to a grounded metal, permanent wiring
system, or an equipment-grounding conductor must
be run with the circuit conductors and connected to the
equipment-grounding terminal or lead of the appliance.
PREP PREP ARING ARING THE DISHW THE DISHW
PREPARING PREP PREP ARING THE DISHW ARING THE DISHWASHER FOR INST THE DISHW
At this point the styrofoam, plastic wrap, and the wood
pallet (base) should be removed from the dishwasher.
Now is an excellent time to inspect for any shipping
damage. Should you find any damage, you should
report it to your dealer or builder immediately .
Be sure to remove the toe kick and toe kick insulation
which are wrapped in heavy brown paper and packed
inside the dishwasher.
THE FILL STRIPS THE FILL STRIPS THE FILL STRIPS THE FILL STRIPS THE FILL STRIPS
All ASKO dishwashers (except Models 1805FI and 1895)
have color-coded fill strips to finish off the installation.
To prevent damage to the machine, be sure to remove
the shipping screws that secure the fill strips to the
access panel. These screws are to be thrown away. Do
not replace them into the access panel.
Fill
A c c e s s
Strip
Panel
NOTE: If the cabinet opening is European measurement
(23-1/2 inches [600 mm]), remove the fill strips
to fit the dishwasher into the opening.
Page 6
a n d g r o u n d i n g
UCTIONS UCTIONS UCTIONS UCTIONS
ASHER FOR INST ASHER FOR INST
ASHER FOR INST ASHER FOR INSTALLA
WARNING!
Do not screw the fill
strips back to the
lower access panel;
otherwise, the
machine will have to
be uninstalled if
service is necessary.
NOTE: Access holes
than 1-1/2" in diameter with no sharp
edges.
Damage to the dishwasher could occur if it is not
properly grounded.
WARNING!
Make sure the water supply line,
drain line and branch circuit wiring do not touch
any exposed terminals of dishwasher wiring.
ALLA ALLA
ALLA ALLATION
SLIDES FOR REAR LEGS SLIDES FOR REAR LEGS
SLIDES FOR REAR LEGS SLIDES FOR REAR LEGS SLIDES FOR REAR LEGS
The unit comes with two white plastic slides for the rear
legs to protect the kitchen floor from being damaged
when you slide the unit into place. The slides simply
snap onto the bottom of the rear legs.
Protective slides for rear
legs simply snap onto the
bottom of the legs.
REMO REMO REMOVING REMO REMO VING VING VING THE VING THE THE THE A A A A A CCESS P THE
To remove the access panel, first remove the two screws
on each side of the access panel. There are two tabs at
the top of the access panel that hold the panel in place
against the guard plate. To remove the panel, you must
slide it down below these tabs.
REMOVING REMO REMO REMO REMO VING VING VING VING THE THE THE THE THE T T T T T OE KICK
BRACKETS BRA BRA CKETS CKETS CKETS
BRA BRA CKETS
To remove the toe kick brackets, hold the small metal
spring tab on the outer edge of the base pan toward the
outside of the machine. Continue holding the tab as
you pull straight out on the bracket. ( Note: It may be
stubborn because it's in guide slots on the base pan.)
Toe kick bracket
must not be larger
TION TION
TION TION
CCESS P CCESS P CCESS P CCESS PANEL ANEL ANEL ANEL ANEL
OE KICK OE KICK OE KICK OE KICK