Digital Audio (Digital Audio Input); Sp Config (Speaker Configuration) - Onkyo HT-S6500 Instruction Manual

Digital Audio (Digital Audio Input)

1 2 3 4
"Setup"
Menu Digital Audio
If you connect a component to a digital audio input, you
must assign that input to an input selector. For example, if
you connect your CD player to the OPTICAL IN 1, you
must assign "OPTICAL1" to the "TV/CD" input selector.
Here are the default assignments.
Input selector Default assignment
BD/DVD COAXIAL1
CBL/SAT COAXIAL2
GAME OPTICAL1
PC - - - - -
AUX - - - - -
TV/CD OPTICAL2
■
BD/DVD, CBL/SAT, GAME, PC, AUX, TV/CD
COAXIAL1, COAXIAL2, OPTICAL1,
OPTICAL2:
Select the input to which the component has been
connected.
- - - - -:
Select if the component is connected to an analog
audio input.
Note
• When an HDMI IN is assigned to an input selector in
(➔ page 45), the same HDMI IN will be set as
"HDMI Input"
a priority in this assignment. In this case, if you want to use the
coaxial or optical audio input, make the appropriate selection in
the "Audio Selector" (➔ page 50).
• Supported sampling rates for PCM signals (stereo/mono) from a
digital input (optical and coaxial) are 32/44.1/48/88.2/96 kHz/16,
20, 24 bit.

Sp Config (Speaker Configuration)

5 1 2
Menu
Some of the settings in this section are set automatically
by Audyssey 2EQ
(➔ page 30).
Here you can check the settings made by Audyssey 2EQ
Room Correction and Speaker Setup function, or set them
manually, which is useful if you change one of the
connected speakers after using Audyssey 2EQ Room
Correction and Speaker Setup function.
This section explains how to specify which speakers are
connected and their sizes.
Cone diameter
For speakers with a cone diameter larger than 6-1/2 inches
(16 cm), specify Large (full band). For those with a
smaller diameter, specify Small (default crossover 100Hz).
The crossover frequency can be changed in "Crossover
(Crossover Frequency)".
Note
• These settings are not available in either of the following cases:
– A pair of headphones is connected.
– The "Audio TV Out" setting is set to "On"
– "HDMI Ctrl (RIHD)" is set to "On"
listening through your TV speakers.
■
Subwoofer
Yes
No
3 4 5
"Setup"
Sp Config
® Room Correction and Speaker Setup
(➔ page 52).
(➔ page 52) and you're
En-46
Advanced Operations
■
Front
Small:
Large:
Select based on the cone diameter.
Note
• If the "Subwoofer" setting is set to "No", this setting is fixed to
"Large".
■
Center , Surround
*1 *1
Small:
Large:
Select based on the cone diameter.
None
Note
*1 If the "Front" setting is set to "Small", the "Large" option
cannot be selected.
■
Crossover (Crossover Frequency)
This setting is advantageous for the speakers that you
specified as "Small" in
"Sp Config (Speaker
. To get the best bass performance from
Configuration)"
your speaker system, you need to set the crossover
frequency according to the size and frequency response
of your speakers.
40Hz, 50Hz, 60Hz, 70Hz, 80Hz, 90Hz, 100Hz,
120Hz, 150Hz, 200Hz
Use the diameter of the smallest speaker in your system
when choosing the crossover frequency.
Speaker cone diameter Crossover frequency
Over 8 in. (20 cm) 40/50/60 Hz
6-1/2 to 8 in. (16 to 20 cm) 70/80/90 Hz
5-1/4 to 6-1/2 in. (13 to 16 cm) 100 Hz
3-1/2 to 5-1/4 in. (9 to 13 cm) 120 Hz
Under 3-1/2 in. (9 cm) 150/200 Hz
* Choose the setting matching your speaker.
*
*
*
To be continued