Basic Playback; Playing A Source; Playing An Ipod - Pioneer Elite SC-57 Operating Instructions Manual

05

Basic playback

Basic playback

Playing a source

Here are the basic instructions for playing a
source (such as a DVD disc) with your home
theater system.
1 Switch on your system components
and receiver.
Start by switching on the playback compo-
nent (for example a DVD player), your TV and
subwoofer (if you have one), then the receiver
(press u RECEIVER).
Make sure that the TV's video input is set to this
receiver.
2 Select the input function you want to
play.
You can use the input function buttons on the
remote control, INPUT SELECT, or the front
panel INPUT SELECTOR dial.
! If you need to manually switch the input
signal type press SIGNAL SEL (page 45).
3 Press to the receiver operation
mode.
4 Press AUTO/ALC/DIRECT
(AUTO SURR/ALC/STREAM DIRECT) to
select 'AUTO SURROUND' and start
playback of the source.
If you're playing a Dolby Digital or DTS surround
sound source, you should hear surround sound.
If you are playing a stereo source, you will only
hear sound from the front left/right speakers in
the default listening mode.
! You may need to check the digital audio
output settings on your DVD player or digital
satellite receiver. It should be set to output
Dolby Digital, DTS and 88.2 kHz / 96 kHz PCM
(2 channel) audio, and if there is an MPEG
audio option, set this to convert the MPEG
audio to PCM.
36
En
! See also Listening to your system on page 43
for information on different ways of listening
to sources.
It is possible to check on the front panel dis-
play whether or not multi-channel playback is
being performed properly. For details, see Auto
Surround, ALC and Stream Direct with different
input signal formats on page 97 .
When using a surround back speaker,
2DIGITAL is displayed when playing Dolby
Digital 5.1 channel signals, and DTS is dis-
played when playing DTS 5.1-channel signals.
If the display does not correspond to the input
signal and listening mode, check the connec-
tions and settings.
5 Use the MASTER VOLUME +/– to adjust
the volume level.
Turn down the volume of your TV so that all
sound is coming from the speakers connected
to this receiver.
Playing a source with HDMI
connection
% Use INPUT SELECT to select the input
function connected to the receiver's HDMI
input terminals.
You can also perform the same operation by
using the INPUT SELECTOR dial on the front
panel or by pressing HDMI on the remote con-
trol repeatedly.
! Set the HDMI parameter in Setting the Audio
options on page 56 to THROUGH if you want
to hear HDMI audio output from your TV (no
sound will be heard from this receiver).
! If the video signal does not appear on your
TV, try adjusting the resolution settings on
your component or display. Note that some
components (such as video game units) have
resolutions that may not be converted. In this
case, use an analog video connection.
Selecting the multichannel analog
inputs
SC-57 only
If you have connected a decoder or a DVD
player as above, you must select the analog
multichannel inputs for surround sound
playback.
! When the center or surround speakers are
bi-amped, no sound is produced even when
MULTI CH IN is selected. (Check Determining
the speakers' application on page 13 and Bi-
amping your speakers on page 16 .)
! When playback from the multichannel inputs
is selected, only the volume and channel levels
can be set.
! With MULTI CH IN inputs, it is possible to play
pictures simultaneously. For details, see Multi
Channel Input Setup on page 81 .
1 Make sure you have set the playback
source to the proper output setting.
For example, you might need to set your DVD
player to output multichannel analog audio.
2 Press on the remote control,
then use INPUT SELECT c/d to select
MULTI CH IN.
You can also use the INPUT SELECTOR dial on
the front panel.
! Depending on the DVD player you're using,
the analog output level of the subwoofer
channel may be too low. In this case,
the output level of the subwoofer can be
increased by 10 dB in the Multi Ch In Setup
in Other Setup. For details, see Multi
Channel Input Setup on page 81 .

Playing an iPod

This receiver has the iPod iPhone iPad USB
terminal that will allow you to control playback
of audio content from your iPod using the con-
trols of this receiver.
! This receiver is compatible with the audio and
video of the iPod nano (audio only for the iPod
nano 1G/2G/6G), iPod fifth generation (audio
only), iPod classic, iPod touch, iPhone, iPhone
3G, iPhone 3GS, iPhone 4 and iPad. However,
some of the functions may be restricted for
some models. The receiver is not compatible
with the iPod shuffle.
! This receiver has been developed and tested
for the software version of iPod/iPhone/iPad
indicated on the website of Pioneer (http://
pioneer.jp/homeav/support/ios/na/).
! Installing software versions other than
indicated on the website of Pioneer to your
iPod/iPhone/iPad may result in incompatibility
with this receiver.
! iPod, iPhone and iPad are licensed for
reproduction of non-copyrighted materials
or materials the user is legally permitted to
reproduce.
! Features such as the equalizer cannot
be controlled using this receiver, and we
recommend switching the equalizer off before
connecting.
! Pioneer cannot under any circumstances
accept responsibility for any direct or indirect
loss arising from any inconvenience or loss
of recorded material resulting from the iPod
failure.
! When listening to a track on the iPod in the
main zone, it is possible to control the sub
zone, but not to listen to a different track in
the sub zone from the one playing in the main
zone.
1 Press u RECEIVER to switch on the
receiver and your TV.
See Connecting an iPod on page 29 .
! It is also possible to operate the iPod on the
iPod itself, without using the TV screen. For
details, see Switching the iPod controls on
page 37 .