Download Print this page

BENDIX TRAILER SYSTEM GUARD AIR DRYER Manual

Advertisement

Quick Links

®
®
Bendix
Trailer System-Guard
21
CONTROL OUTLET
22
SUPPLY OUTLET
FIGURE 1 - TRAILER SYSTEM-GUARD
DESCRIPTION
®
The Bendix
Trailer System-Guard
moisture and contaminates from the trailer air system. It is
not intended to take the place of a dryer normally located
on the power unit. It acts as a buffer to remove moisture
during wet times and gives up water vapor during dry times.
It protects the trailer air brake system when, for short periods
of time, the trailer is pulled by vehicles without an air dryer
or during times when the trailer is disconnected from the
tractor.
The Trailer System-Guard
desiccant air dryers mounted in a single housing, one to
protect the trailer service system and the other to protect
the trailer supply system.
PREVENTIVE MAINTENANCE
Every 300 operating hours, 8,000 miles, or one (1)
month:
1. Visually inspect for physical damage or wear to the Trailer
System-Guard
air dryer. This can include, but is not
limited to, chaffed or broken air hoses and or broken or
missing parts.
Air Dryer
ALL SUPPLY & CONTROL PORTS 1/4" NPT
AIR DRYER
air dryer removes
air dryer consists of two
2. Check mounting bolts for tightness. If loose re-torque
per "Mounting the Trailer System-Guard
Every 900 operating hours or 25,000 miles or every
three (3) months:
Check for moisture in the air brake system by opening
reservoirs, drain cocks, or valves and checking for the
presence of water. If moisture is present the tractor and
trailer should be checked for leaks. If leakage is not
excessive check the tractor air dryer for proper operation.
If defective, the tractor dryer should be repaired, rechecking
trailer reservoirs again after 3 months. If the tractor dryer
operates satisfactorily and the trailer has not been
connected to a tractor without an air dryer and the trailer
glad hands were not open to the atmosphere for some
extended period of time, the trailer dryer should be replaced.
If the trailer has been connected to a tractor without an air
dryer or the trailer has been parked for an extended period
of time, the trailer should be coupled to a tractor with an air
dryer. This will help the trailer air dryer remove moisture
from the trailer. Place the unit back in service and recheck
for moisture after 3 months.
3/8 - 16 UNC x .50 Deep
Mounting Holes (4)
11
CONTROL INLET
12
SUPPLY INLET
Air Dryer".
1

Advertisement

loading

Summary of Contents for BENDIX TRAILER SYSTEM GUARD AIR DRYER

  • Page 1 2. Check mounting bolts for tightness. If loose re-torque ™ per "Mounting the Trailer System-Guard Air Dryer". ® ™ The Bendix Trailer System-Guard air dryer removes Every 900 operating hours or 25,000 miles or every moisture and contaminates from the trailer air system. It is three (3) months: not intended to take the place of a dryer normally located on the power unit.
  • Page 2: Personal Injury Or Death

    AIR DRYER: GENERAL pressures. The following instructions are presented for reference 7. Never connect or disconnect a hose or line purposes only, since Bendix aftermarket replacement Trailer containing pressure; it may whip. Never remove a ™ System-Guard air dryers are packaged with the most up- component or plug unless you are certain all to-date installation instructions.
  • Page 3 SUPPLY LINE -CHARGING CONTROL CONTROL SUPPLY SUPPLY SUPPLY LINE - PARKING CONTROL CONTROL SUPPLY SUPPLY CONTROL CONTROL LINE - BRAKE APPLICATION CONTROL SUPPLY SUPPLY CONTROL CONTROL CONTROL LINE - BRAKE RELEASE SUPPLY SUPPLY ™ FIGURE 2 - TRAILER SYSTEM-GUARD AIR DRYER OPERATION (VIEWED FROM MOUNTING HOLE SIDE)
  • Page 4: Connecting The Air Hoses

    Template for mounting holes Grommet Vise Grip Clamping Area Grommet Stud Frame Rail Washer Locknut ™ Trailer System Guard Air Dryer FIGURE 3 - TRAILER SYSTEM-GUARD ™ AIR DRYER INSTALLATION 2. Drill the three marked mounting holes into the frame 6.
  • Page 5: Operational Test

    Spring "11 IN Brake CONT" "12 IN SUP" Trailer ™ System-Guard Dryer "21 OUT "22 OUT CONT" R-12 ™ Relay SUP" Valve Supply Reservoir Spring Brake Valve ™ If the trailer is equipped with an R-12P valve, the trailer systems guard must be mounted upstream of the R-12P ™...
  • Page 6 TEMPLATE INCLUDED - DO NOT REDUCE THIS DOCUMENT BW2083 © 2004 Bendix Commercial Vehicle Systems LLC All rights reserved. 7/2004 Printed in U.S.A.

This manual is also suitable for:

Trailer system-guard