Table of Contents
Advertisement
BASIC OPERATIONS (CONT.)
Your PSX™ comes with a built in sampler. You may store up to three samples on the three FLASH BUTTON (6)
(Once again please note you may only store either a CUE POINT or a SAMPLE into a FLASH BUTTON (6), not
both).Your sample can be a maximum of 7 seconds in length. A sample can be recalled while a CD is playing, or
while the CD drive is in PAUSE MODE. You may play your sample at anytime without music interruption. If you
play your sample when the unit is already in playback mode you sample will over lap the current music source.
You can also play your sample once or in a continuous loop. As with cue points you may store approximately
384 (128 x 3) samples in a drives memory (depending on available memory). The MEMORY BUCKET (52) on
the LCD DISPLAY (1) will approximate the remaining memory.
To create a sample:
1) Initialize a loop (see creating a seamless loop on page 15). If your loop is longer than 6.5 seconds it
can not be stored as a sample and will stored as a Cue Point.
2) Press the MEMORY BUTTON (7). The
MEMORY CUE BUTTON (1) Red LED will
glow indicating memory is ready to be stored.
4) The red MEMORY BUTTON (7) LED will turn off, when your sample is locked
into memory.
1 2 3 4 5 6 7 8 9 0
AUTO
CUE
CUE
ELAPSED
TOTAL
REMAIN
.
SINGLE
LOOP
RELOOP
T
PITCH
M
S
F
SCRATCH
FLANGER
HOLD
ECHO
TRANS
PARAMETER
TIME
8%/12%/16%
Figure 26
Important Notice:
the sample function on, the Flash button (6) will act as cue points!
1 2 3 4 5 6 7 8 9 0
AUTO
CUE
CUE
ELAPSED
TOTAL
REMAIN
.
SINGLE
LOOP
RELOOP
T
M
S
F
PITCH
EJECT/
STOP
SCRATCH
FLANGER
HOLD
ECHO
TRANS
PARAMETER
SGL/CTN
TIME
AUTO CUE
8%/12%/16%
ON/OFF
SAMPLE PITCH
5) At this point your sample has been stored into memory. The original loop you
used to create the sample will remain playing until the OUT BUTTON (18) is
pressed (Figure 26).
EJECT/
STOP
SGL/CTN
AUTO CUE
ON/OFF
6) Your sample can now be recalled at any time
even
when the unit is in PAUSE MODE. To recall
SAMPLE PITCH
the sample be sure the sample function is on, by
pressing the SAMPLE BUTTON (8) until the red sam-
ple button LED turns on. To play your sample in a
continuos loop leave the sample function on. To play
your sample just once, turn the sample function off
immediately after initiating your sample. With the
sample function on the sample will continue to play
until the sample function is turned off.
If you try to activate your sample without turning
American Audio
- www.americanaudio.us - PSX™ Instruction Manual Page 18
©
®
Figure 24
3) Select one of the three FLASH BUTTON
(6) you wish to store your loop in and press
that button.
1 2 3 4 5 6 7 8 9 0
AUTO
CUE
CUE
ELAPSED
TOTAL
REMAIN
.
SINGLE
LOOP
RELOOP
T
PITCH
M
S
F
EJECT/
STOP
SCRATCH
FLANGER
HOLD
ECHO
TRANS
PARAMETER
SGL/CTN
TIME
AUTO CUE
8%/12%/16%
ON/OFF
SAMPLE PITCH
1 2 3 4 5 6 7 8 9 0
CUE
SINGLE
LOOP
RELOOP
SCRATCH
Figure 27
Figure 25
AUTO
CUE
ELAPSED
TOTAL
REMAIN
.
T
M
S
F
PITCH
EJECT/
STOP
FLANGER
HOLD
ECHO
TRANS
PARAMETER
SGL/CTN
TIME
AUTO CUE
8%/12%/16%
ON/OFF
SAMPLE PITCH
Advertisement
Table of Contents
