Table of Contents
Advertisement
<
CONTENTS
CONTENTS (ENGLISH)
1
INTRODUCTION
2
UNPACKING
3
EM15 IMPEDANCE
4
SAFETY FIRST
4.1 Rigging and suspension
5
AMPLIFICATION
6
CONNECTING TO AN AMPLIFIER
7
SYSTEM CONFIGURATIONS
8
WARRANTY
9
TECHNICAL SPECIFICATIONS
>
PRINT
The Martin Experience
Martin Audio – EM SERIES
MARTIN AUDIO
L O N D O N
GUIDES
Page No
2
2
3
4
4
4
5
5
7
8
Advertisement
Table of Contents
Related Manuals for Martin Audio EM15
Summary of Contents for Martin Audio EM15
- Page 1 CONTENTS (ENGLISH) Page No INTRODUCTION UNPACKING EM15 IMPEDANCE SAFETY FIRST 4.1 Rigging and suspension AMPLIFICATION CONNECTING TO AN AMPLIFIER SYSTEM CONFIGURATIONS WARRANTY TECHNICAL SPECIFICATIONS MARTIN AUDIO L O N D O N The Martin Experience Martin Audio – EM SERIES...
-
Page 2: Introduction
ICT™ (Inductively Coupled Transducer) technology. The EM150 is a twin 10"(250mm) driver sub-bass system designed to be used to extend the low frequency performance of the EM15. It can also be used with larger EM Series enclosures such as the EM26. -
Page 3: Em15 Impedance
The EM15 can be configured as either a 4 ohm or 16 ohm loudspeaker. The 16 ohm configuration allows up to 4 x EM15’s to be run in parallel from a single amplifier channel. The EM15 is normally supplied from the factory in the 4 ohm configuration. -
Page 4: Safety First
Seek help from architects, structural engineers or other specialists if in any doubt. AMPLIFICATION The EM15 and EM150 are designed to be used with professional power amplifiers capable of producing the following power outputs into 4 ohms: EM15 4 ohm... -
Page 5: Connecting To An Amplifier
The basic system configuration for one EM150 and up to six EM15’s is shown in Fig 2. Up to three EM15’s (each in 16 ohm configuration) are wired in parallel with the respective left and right inputs of the EM150, and driven from the left and right channels of the power amplifier. - Page 6 PRINT GUIDES To allow for the addition of further EM15’s and balance control between the EM15’s and the EM150, a further power amplifier may be added to the system as shown in Fig 3. The same signal is fed into both amplifiers, one driving the EM15’s, the other driving the EM150.
-
Page 7: Warranty
4 ohm 4 ohm RIGHT CHANNEL LEFT CHANNEL Note: Care must be taken, when connecting EM15’s in parallel, to ensure that the total load impedance presented to the power amplifier will not exceed the minimum specified by the amplifier manufacturer. WARRANTY... -
Page 8: Technical Specifications
(W) 6.8ins x (H) 11ins x (D) 6.8ins WEIGHT 5kg (11lbs) SHIPPING DIMENSIONS (W) 390mm x (H) 370mm x (D) 200mm (Packed in pairs) (W) 15.4ins x (H) 14.5ins x (D) 7.9ins SHIPPING WEIGHT 9kg (19.8lbs) (Packed in pairs) Martin Audio – EM SERIES... - Page 9 SPL measured at 1 metre using band limited pink noise. Finish: Textured grey green paint. Protective grilles: Perforated steel grey with 48% free air flow. Due to our policy of continuous improvement all specifications are subject to change without notice. Martin Audio – EM SERIES...
-
Page 10: Visit Our Website
< > CONTENTS PRINT GUIDES EM Series EM15/EM150 Please Click here to return to main menu Please Click here to visit our website MARTIN AUDIO L O N D O N The Martin Experience Century Point, Halifax Road, Cressex Business Park, High Wycombe, Buckinghamshire HP12 3SL, England. - Page 11 < > CONTENTS PRINT GUIDES EM Series EM15/EM150 User’s Guide ENGLISH MARTIN AUDIO L O N D O N The Martin Experience...