Memorizing The Channels - Samsung PL-42C71HDP Owner's Instructions Manual

Memorizing the Channels

Your TV can memorize and store all of the available channels for both "off-air" (air) and cable channels.
After the available channels are memorized, use the CH
This eliminates the need to change channels by entering the channel digits. There are three steps for memorizing
channels: selecting a broadcast source, memorizing the channels (automatic) and adding or deleting channels
(Channel Lists).
Selecting the Video Signal-source
Before your television can begin memorizing the available channels, you must specify
the type of signal source that is connected to the TV (i.e. an air or a cable system).
1 Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Channel, then press the ENTER button.
2 Press the ENTER button select Antenna.
Press the ▲ or ▼ button to select Air or Cable, then press the ENTER button.
Press the EXIT button to exit.
Storing Channels in Memory (Automatic Method)
1 Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Channel, then press the ENTER button.
2 Press the ▲ or ▼ button to select Auto Program, then press the ENTER button.
3 Press the ▲ or ▼ button to select the antenna connection, then press the ENTER
button.
➢ Air: "Air" antenna signal.
Cable: "Cable" antenna signal.
Air+Cable: "Air" and "Cable" antenna signals.
If the antenna is connected to ANT 2 IN(CABLE), select Cable and if it is
➢
connected to ANT 1 IN(AIR), select Air.
If both ANT 1 IN and ANT 2 IN are connected, select the Air + Cable.
➢
➢ If you selected Air, then go to step 5.
4 Press the ▲ or ▼ to select the correct analog signal cable system source among
STD, HRC, and IRC, then press the ENTER button. If you have Digital cable,
select the cable system signal source for both Analog and Digital.
➢ If you have Digital cable TV, select the signal source for both Analog and
Digital.
➢ STD, HRC, and IRC identify various types of cable TV systems. Contact your
local cable company to identify the type of cable system that exists in your
particular area. At this point the signal source has been selected.
5 The TV begins memorizing all available stations.
If you want to stop Auto Programming, press the ENTER button. The Stop Auto
Program? message will be displayed. Select Yes by pressing the ◄ or ► button.
Press the EXIT button to exit.
➢ The TV must be connected to an antenna/cable in order to receive digital
TV signals. Even if a particular channel is deleted from the memory, you can
always tune to that channel directly by using the number buttons on the remote
control.
➢ • All available DTV and analog channels are automatically stored in memory.
• It takes approximately 3 to 10 minutes to memorize channels.
You can also press the AUTO PROG. button on the remote control to bring up the
AutoProgram menu.
BN68-01192B_Eng-1.indd 20
or CH button to scan through the channels.
English - 20
T V Channel
Antenna : Air ►
Auto Program ►
Clear Scrambled Channel ►
Channel List ►
Name ►
Fine Tune ►
Signal Strength ►
LNA : On ►
Move
Enter Return
T V Channel
Air
Antenna : Air
Cable
Auto Program
Clear Scrambled Channel
Channel List
Name
Fine Tune
Signal Strength
LNA : On
Move
Enter Return
T V Channel
Antenna : Air ►
Auto Program ►
Clear Scrambled Channel ►
Channel List ►
Name ►
Fine Tune ►
Signal Strength ►
LNA : On ►
Move
Enter Return
T V Auto Program
Select the antennas to memorize.
Air
Start
Start
Cable
Start
Air + Cable
Move Enter Return
T V Auto Program
Select the cable system.
Analog
Start
STD
HRC
IRC
Digital
STD
HRC
IRC
Move Enter Return
Auto Program
Auto Program in progress.
Cable Channel 67
68 %
Stop
Enter Return
Auto Program
Stop Auto Program?
68 %
Yes No
�����
Move Return
Enter
���
��
2007-04-30 ｿﾀﾈﾄ 6:27:00