Delta Electronics Programmable Logic Controller DVP-SC Instruction Sheet

Warning
This Instruction Sheet only provides descriptions for electrical specifications, general specifications, installation &
wiring. Other detail infromation about programming and intructions is compatible with SA/SX/SC series; please see
PLC Application Manual. For more information about the optional peripherals, please see individual product
instuction shee or "DVP-PLC Application Manual: Special module".
This is an OPEN TYPE PLC. The PLC should be kept in an enclosure away from airborne dust, humidity, electric
shock risk and vibration. Also, it is equipped with protective methods such as some special tools or keys to open the
enclosure, in order to prevent hazard to users or damage the PLC..
Do NOT connect the AC main circuit power supply to any of the input/output terminals, or it may damage the PLC.
Check all the wiring prior to power up. To prevent any electromagnetic noise, make sure the PLC is properly
grounded . DO NOT touch terminals when power on.
Introduction
Thank you for choosing DELTA's PLC DVP series. The DVP-SC series has a 12-points (8 input points + 4
outputs) MPU with powerful instructions (the same instruction sets as SA/SX/SC series) for use. It also has an
8K Steps program memory and high-speed pulse inputs(X10 and X11)/outputs (Y10 and Y11). For high-speed
pulse, total bandwidth can up to 130KHz and 100KHz maximum for single input/output. Besides, it also
provides instructions of position control and zero point return to use with high-speed pulse output. It could
connect all extension units of DVP-SS series for various applications.
Product Profile and Outline
Unit: mm
Battery replacement: Battery replacement must be finished within 3 minutes, or the internal data of the PLC
(including the program area, RTC and latched registers) could be lost or destroyed.
1 Status indicators of POWER, RUN and ERROR 12 Extension port for wire to connect extension module/unit
2 RUN/STOP switch 13 Mounting hole
3 VR0: Start-up by M1178/D1178 Corresponding value 14 DIN rail track (35mm)
4 VR1: Start-up by M1179/D1179 Corresponding value 15 Extension unit clip
5 DIN rail clip 16 RS-485 communication port (Master/Slave)
6 I/O terminals 17 DC Power input
7 I/O point indicators 18 2 pin removable terminal (standard accessory)
8 COM1 (RS-232) (Rx) indicator 19 Power input cable (standard accessory)
9 COM2 (RS-485) (Tx) indicator 20 Battery cover
10 COM1 (RS-232) port 21 Battery socket connection
11 Nameplate 22 Battery holder
Specifications
Model
DVP12SC11T
Item
Power supply voltage MPU: 24V DC (-15% ~ +20%) (With DC input reverse polarity protection),
Fuse
2A/250V AC
Power consumption 4W MAX
Insulation resistance 5 M Ω and above at 500V DC (Between all inputs/outputs and earth)
ESD: 8KV Air Discharge
EFT: Power Line: 2KV, Digital I/O: 1KV, Analog & Communication I/O: 250V
Noise immunity
Damped-Oscillatory Wave: Power Line: 1KV, Digital I/O: 1KV
RS: 26MHz ~ 1GHz, 10V/m
The diameter of grounding wire cannot be smaller than the wire diameter of terminals L
Grounding
and N (All DVP units should be grounded directly to the ground pole).
Operation: 0°C ~ 55°C (temperature), 50 ~ 95% (humidity), pollution degree 2;
Environment
Storage: -25°C ~ 70°C (temperature), 5 ~ 95% (humidity)
Vibration/shock resistance Standard: IEC61131-2, IEC 68-2-6 (TEST Fc)/IEC61131-2 & IEC 68-2-27 (TEST Ea)
Weight (approx. g) 158
Certificates
Input Point Electrical Specification
Input type DC (SINK or SOURCE)
Input current 24V DC 5mA
Off → On,
X0, X1, 18.5V DC and above
X2 ~ X5, 16.5V DC and above
Active level
X10, X11, 18.5V DC and above
On → Off,
X0 ~ X5, X10, X11, below 8 V DC
Hardware The constant of filter time is 10ms
X0~X5
Software 0 ~ 20ms (Set by D1020)
Response time
Hardware The constant of filter time is 4.7us
X10, X11
Software 0 ~ 1,000 times (Set by D1021)
Output Specifications
Output type Transistor
0.3A/1 point @ 40°C (Room Temp.)
Rated current
When the output of Y0 and Y1 is high-speed pulse above 3KHz, Y0, Y1 ,Y10 and Y11 = 30mA
Voltage specification 5 ~ 30V DC
Max. inductive load
7.2W/24V
Internal None
Output protection
Outside Rated value according to the load
Y0, Y1 9W/1 point
Maximum loading
Y10, Y11 0.9W/1 point
< 20us
Off → On
< 1us (Y10, Y11 only)
Response time
< 30us
On → Off
< 1us (Y10, Y11 only)
Battery life:
Temperature ( C )
° 0 25 50 70
Life (years) 9 8 6 5
Precision of calendar timer:
At 0 C /32 F , less than -117 seconds error per month.
° °
At 25 C /77 F , less than 52 seconds error per month.
° °
At 55 C /131 F , less than -132 seconds error per month
° °
Model Name & I/O Configuration
ENGLISH
Input/Output Specification
Model Input Unit Output Unit
Power
Points Type Points Type
24V DC
Transistor
6 Sink/Source 2
Y0, Y1
X0~X5
DVP12SC11T 24V DC
24VDC
Transistor
Sink/Source
2 2 Hi-speed
Hi-speed
Y10, Y11
X10, X11
Installation & Wiring
4.1 PLC Mounting Arrangements and Wiring Notes
1. When installing the DVP series PLC, make sure that it is installed in an
enclosure with sufficient space (as shown on the right) to its
surroundings so as to allow heat dissipation.
2. I/O signal wires or power supply should not run through the same
multi-wire cable or conduit.
3. Please use 22-16AWG (1.5mm) wiring (either single or multiple core)
for I/O wiring terminals. The specification for the terminals is as shown
on the right.
4. PLC terminal screws should be tightened to a torque of 1.95 kg-cm (1.7
in-lbs).
5. Use copper conductor only, 60/75 C
°
4.2 Wiring Notes
Environment
1. DO NOT store the PLC in an atmosphere that is dusty, smoky, with metallic debris or corrosive or
flammable gases.
2. DO NOT store the PLC in an environment with high temperature or high humidity.
3. DO NOT install the PLC on a shelf or on an unstable surface.
Power Input Wiring
DVP-SC series input power supply is DC input. Please take a note of listed items when operating DVP-SC
Series.
1. Please make sure the power is at terminals 24V DC and 0V (power range is 20.4 ~ 28.8V DC). When
voltage is lower than 20.4V DC, PLC will stop operating, all outputs will be Off and ERROR LED will flash
continuously.
2. If the power-cut time is less than 10ms, the PLC still operates unaffectedly. If the power-cut time is too
long or the power voltage drops, the PLC will stop operating and all the outputs will be Off. Once the
power is restored, the PLC will return to operation automatically. (There are latched auxiliary relays and
registers inside of the PLC, please be aware when programming.)
20.4V~28.8V
24V
0V
DC Input Type
2A
Safety Wiring
Since the PLC is used to control numerous devices, motion of either one device could affect the motion of other
devices. Therefore the breakdown of a device would consequently be detrimental to the whole auto control
system, thus the result is dangerous. Please use the recommended wiring below for the power input
(DVPPS01/DVPPS02):
5
MC
1
4
8
2
G uard
Lim it
M C
3
MC
1
L N 7
6
Input Point Wiring
The DC power is used for DC input signal. Two types of DC wiring are used: SINK and SOURCE, defined as
follows:
Sink = Current flows into the common terminal S/S
S/S
Sinking
X0
Input Point Loop Equivalent Circuit
+2 4V
24V D C
DC Type
24 G
(DC Signal IN)
S/S
X0
SINK Mode
Input Point Loop Equivalent Circuit
+ 24 V
I/O Configuration
24 V D C
DC Type
24 G
(DC Signal IN)
S/S C0
X0 Y0
S/S
X1 C1
X2 Y1 X0
X3 C2 SOURCE Mode
X4 Y10
X5 C3
Output Point Wiring
X10 Y11
X11 DVP-**-**-11-T
LED
1. Two types of DVP-SC Series PLC output modules Transistor. For the electrical specification, please refer
D
to the function specification.
D DV P D
2. Please watch out the connection of common terminals while wire the outputs. Output terminal Y0 uses one
M P U
common terminal C0, Y1 uses C1, and Y10 uses C2, Y11 uses C3, as shown below:
D
D > 50 mm
22 -1 6AW G
C0 Y0 C1 Y1 C2 Y10 C3 Y11
Action indication: When the output point is active, the corresponding indicator at the front panel will be on.
< 1.5m m
3. Isolated circuit: The optical coupler is used to isolate signals between PLC internal circuits and input
modules.
Input/Output Wiring
24V DC
S/ S
X0
X1
X5
High-speed pulse
in put s
100KHz
X1 0
High-speed pulse
in put s
100KHz
X11
X10 and X11 can be used as common inputs
or inputs of high-speed counter
注 意 事 項
S/S X0 X1 X2
DVP-PLC
DC/DC 5V
(OPEN TYPE)
產 品 簡 介
Power supply for AC loads
DVP-SC
Power Circuit Protection Fuse (3A)
8K Steps
Power indicator
Emergency stop 100KHz
The machinery must provide a quick manual method
disconnecting all system power.
Circuit isolation device (System Power Disconnect)
產 品 外 觀 及 各 部 介 紹
Utilize the electromagnetic contactor and the relay to be the
isolation unit of the power circuit to prevent the possible instability
of the system when the power is supplied on and off.
DVPPS01/DVPPS02
Earth
Power supply:
AC: 100 ~ 240V AC, 50/60Hz
Source = Current flows out of common terminal S/S
電 池 安 裝 ： ： ： ： 電 池 安 裝 電 池 安 裝 電 池 安 裝
X0
S/ S
Sou rcin g
Wiring Loop
1
2 RUN STOP
3 VR0 M1178
4 VR1 M1179
S I NK
+ 5V DIN
5
6
+24V OV S/S X0 X1 X2
7 /
24 VDC
Sink Ty pe 8 RS-232
9 RS-485
10 RS-232
11
電 氣 規 格
Wiring Loop
S OU R C E
+ 5 V
+24V OV S/S X0 X1 X2
24VD C
Source Type
LOAD
Y0
T
< 0.3A
R
G
C0
, g
TRANSISTOR OUTPUT
30 mA~0.3 A
LOAD
Y0
5VD C~ 30V DC
C0
Y1
C1
Y1 0 High-speed pulse
outp uts
CH 0
100K Hz
電 池 壽 命 電 池 壽 命 ： ： ： ：
C2 電 池 壽 命 電 池 壽 命
( C)
Y11 High-speed pulse
( )
outp uts
CH 1
100K Hz
C3
萬 年 曆 的 精 度 （ （ （ （ 秒 秒 秒 秒 ） ： ） ： ） ： ） ： 萬 年 曆 的 精 度 萬 年 曆 的 精 度 萬 年 曆 的 精 度
0 C/32 F
Y10 and Y11 can be used as common outputs or
high-speed pulse outpus used with position control 25 C/77 F
55 C/131 F
繁 體 中 文 繁 體 中 文
繁 體 中 文 繁 體 中 文
SA/SX/SC
DVP-PLC
/
12 8 + 4 PLC SA/SX/SC
(X10 X11) (Y10 Y11) 130KHz
SS
mm
12
13
D1178 14 DIN (35mm)
D1179 15
RS-485 (Master/Slave)
16
17
18 2 pin
(Rx) 19
(Tx) 20
21
22
DVP12SC11T
24V DC (-15% ~ +20%)
2A/250V AC
4W MAX
5 M 500V DC
ESD: 8KV Air Discharge
EFT: Power Line: 2KV, Digital I/O: 1KV, Analog & Communication I/O: 250V
Damped-Oscillatory Wave: Power Line: 1KV, Digital I/O: 1KV
RS: 26MHz ~ 1GHz, 10V/m
L, N PLC
0°C ~ 55°C 50 ~ 95% 2
-25°C ~ 70°C 5 ~ 95%
IEC61131-2, IEC 68-2-6 (TEST Fc)/IEC61131-2 & IEC 68-2-27 (TEST Ea)
158 (g)
SINK SOURCE
24V DC 5mA 10 ms
Off → On,
X0 X1 18.5V DC
X2 ~ X5 16.5V DC
X10 X11 18.5V DC
On → Off,
X0 ~ X5 X10 X11 8V DC
10 ms
X0 ~ X5 D1020 0 ~ 20 ms
4.7us
X10 X11 D1021 0 ~ 1,000
0.3A/1 @ 40°C
3KHz
Y0 Y1 Y10 Y11 30mA
30V DC
9W/1
0.9W/1
Off On 20us, On Off 30us
Off On 1us, On Off 1us
0 25 50 70
9 8 6 5
-117
52
-132