HP J4367A - UPS R3000 XR Installation Instructions Manual
Hp ups r3000 erm installation instructions
Hide thumbs
Also See for J4367A - UPS R3000 XR:
- Best practices manual (27 pages) ,
- User manual (65 pages)
Advertisement
HP UPS R3000 ERM
Installation Instructions
© Copyright 2000, 2006 Hewlett-Packard Development Company, L.P.
The information contained herein is subject to change without notice. The
only warranties for HP products and services are set forth in the express
warranty statements accompanying such products and services. Nothing
herein should be construed as constituting an additional warranty. HP shall
not be liable for technical or editorial errors or omissions contained herein.
October 2006 (Seventh Edition)
Part Number 192132-007
Overview
The ERM consists of two battery packs in a 2U chassis. The
ERM connects directly to a UPS R3000 or to another ERM.
Up to two ERM units can be connected.
At the HP recommended 80 percent load, one ERM extends
the available UPS runtime up to 30 minutes.
For more information about any of the topics covered in this
document, see the UPS user guide located on the
documentation CD or HP website
(http://www.hp.com/go/rackandpower).
Precautions
WARNING: A risk of personal injury from
electric shock and hazardous energy levels
exists. The installation of options and routine
maintenance and service of this product
must be performed by individuals who are
knowledgeable about the procedures,
precautions, and hazards associated with AC
power products.
This symbol indicates that the ERM
exceeds the recommended weight for
one individual to handle safely.
45 kg
WARNING: To reduce the risk of
100 lb
personal injury or damage to the
equipment, observe local occupational
health and safety requirements and
guidelines for manual material
handling.
CAUTION: Always plan the rack installation so that
the heaviest item is on the bottom of the rack. Install
the heaviest item first, and continue to populate the
rack from the bottom to the top.
Kit contents
Important Safety Information guide
This document
Warranty information
Rails, with mounting hardware for square- and round-
holed racks
ERM
Front bezel
Rear stabilization brackets (2) and associated hardware
ERM power cable
Advertisement
Related Manuals for HP J4367A - UPS R3000 XR
Summary of Contents for HP J4367A - UPS R3000 XR
-
Page 1: Installation Instructions
Warranty information Rails, with mounting hardware for square- and round- holed racks © Copyright 2000, 2006 Hewlett-Packard Development Company, L.P. Front bezel The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express Rear stabilization brackets (2) and associated hardware warranty statements accompanying such products and services. -
Page 2: Tools And Materials
Tools and materials Unpack the equipment near the rack where the unit will be assembled. The following tools are required for installation: CAUTION: Always plan the rack installation so that Phillips screwdriver the heaviest item is on the bottom of the rack. Install the heaviest item first, and continue to populate the 10-mm hex-nut driver rack from the bottom to the top. -
Page 3: Powering Down The Ups
Insert screws through the rack into the mounting rail and Tighten the hex nuts. the front of each mounting bracket. Install the rear stabilization bracket using hex nuts. Wait Install cage nuts or clip nuts into the rear of the rack. until the unit is installed and the brackets are adjusted before tightening the nuts. -
Page 4: Switching Off The Erm Circuit Breaker
Switching off the ERM circuit Attaching the ERM front bezel breaker WARNING: To prevent personal injury from electric shock or damage to the equipment, verify that the circuit breaker is in the Off position. Connecting the ERM to the UPS NOTE: Before connecting an ERM to a UPS, remove the label from the ERM connector. -
Page 5: Configuring The Ups
Switching on the ERM circuit breaker Available Parameter Associated Explanation (when LED is settings illuminated) 127/240 Site Wiring Nominal utility voltage Fault (red) level is set to 127/240 Wiring Wiring Utility Audible alarm will sound fault fault (green) when ground is missing setting or line and neutral connections are reversed... -
Page 6: Ups Front Panel Led Indicators
UPS front panel LED indicators To configure the UPS for the number of connected ERMs, press the On button to advance the cursor to the load LED associated with the number of ERMs attached to the UPS. Press the Standby button to select the appropriate ERM configuration.