Ryobi DP121L Repair Sheet page 3

RYOBI 12 in. DRILL PRESS – MODEL NUMBER DP121L
The model number will be found on a plate attached to the motor housing. Always mention the model
number in all correspondence regarding your DRILL PRESS or when ordering repair parts.
KEY PART
NO. NUMBER
1 08914000080
 08914000906
 TDP07001 * SCREW
4 08914000001
5 140100A
6 TDP0001 * SET SCREW
7 0891400000 * BOLT (M10 X 0 mm HEX) ..4
8 140100A
9 101010A
08914000090
10
089140000
11
TDP06001 * HEX NUT (M8) .....................
1
0891400004
1
08914000007 * SCREW
14
101007
15
1401004B
16
101006
17
101008
18
1610101A
19
08914000010
0
TDP1B0009 * SCREW
1
1401005

110006M1

110006M
4
140007
5
1610008
6
10001A
7
08914000015
8
1000A
9
10006
0
TDP0001
1
TDP10001

0891400006 * SCREW

0891400007
4
0891400005 * SCREW
5
PARTS LIST FOR FIGURE A
DESCRIPTION
BEVEL STOP .......................1
RPM LABEL ........................1
(M5 X 6 mm PAN HD.) .........9
BASE ...................................1
COLUMN HOLDER .............1
(M8 X 10 mm HEX SOC.) ....
TUBE COLUMN ..................1
RACK ..................................1
COLUMN COLLAR .............1
KNOB ..................................1
CRANK ................................1
(M6 X 8 mm HEX SOC.) ......
GEAR SHAFT ......................1
TABLE SUPPORT .................1
WORM GEAR .....................1
GEAR .................................1
TABLE LOCK HANDLE .......
TABLE ...............................1
(M1 X 5 mm HEX HD.) .....1
ARM-TABLE ........................1
CHUCK KEY .......................1
CHUCK .............................1
ARBOR ................................1
CHUCK TOOL (DRIFT) ........1
SPINDLE .............................1
BEARING (8004) ...............1
QUILL TUBE .......................1
QUILL GASKET ...................1
BALL BEARING (6001) ......1
RETAINING RING (11) ........1
(M.5 X 9.5 mm PAN HD.) ...4
SWITCH ..............................1
(M5 X 5 mm PAN HD.) .......
* Standard Hardware Item – May Be Purchased Locally
KEY PART
QTY. NO. NUMBER
08914000044
6
08914000019
7
16104007A
8
16104009
9
16104008
40
TDP1B06005
41
0891400008
4
0891400004
4
0891400005
44
0891400006
45
TDP0600
46
0891400007
47
0891400008
48
0891400009 * SCREW
49
0891400000
50
0891400001
51
089140000
5
08914000071 * SCREW
5
089140000 * SCREW
54
0891400004
55
0891400005 * SCREW (M. X 6.5 mm) ....4
56
0891400006 * SCREW
57
0891400007
58
0891400008
59
0891400009
60
08914000040
61
08914000041
6
0891400004
6
0891400004
64
TDP1000
65
0891400009
66
100A
67
08914000045
68
08914000046
69
08914000047
70
0891400008
71

DESCRIPTION
LIGHT SWITCH ...................
SWITCH BOX ......................1
SPRING RETAINER .............1
TORSION SPRING ..............1
CAP SPRING ......................1
HEX NUT (M1) ...................
KNOB ..................................4
HANDLE CLAMP ...............1
FEED HANDLE ....................1
V BELT ................................1
* HEX NUT (M10 mm) ............1
LOCK WASHER (0-1) ........1
SPEED ADJUST-HUB .........1
(M5 X 1 mm PAN HD.) .......
COLLAR SHAFT .................1
KEY (M X 6 mm) ................1
PINION SHAFT ....................1
(M6 X 5 mm HEX SOC.) ......
(M4 X 16 mm PAN HD.) .......
SENSOR .............................1
(M5 X 8 mm HEX SOC.) ......
SPINDLE PULLEY-LOWER .1
SPINDLE PULLEY-UPPER ..1
C-CLIP (SPINDLE PULLEY) 1
BEARING (61907) ...............1
RETAINING RING (5) .........1
DRIVE PLATE ......................1
RETAINING RING (4) .........1
RETAINING RING (17) .........1
BALL BEARING (600) ......
SPACER ..............................1
INSERT PULLEY .................1
KEY (M4 X 60 mm) ..............1
POWER CORD ....................1
HEX KEY (5 mm) .................1
QTY.