Page 3
This section tells you when to perform vehicle maintenance and what fluids and lubricants to use............Customer Assistance Information This section tells you how to contact Chevrolet for assistance and how get service and owner publications. also gives you infomation on “Reporting Safety Defects” on page 8-8.
For For Canadian Owners Who Prefer a vehicles first sold in Canada, substitute the name “General Motors of Canada Limited” for Chevrolet French Language Manual: Division whenever it appears in this manual. Aux propridtaires canadiens: Vous pouvez vous...
How to Use this Manual Safety Warnings and Symbols You will find a number of safety cautions in this book. Many people read their owner’s manual from beginning to end when they first receive their new vehicle. If you We use a box and the word CAUTION to tell you about things that could hurt you if you were to ignore do this, it will help you learn about the features and controls for your vehicle.
You will also find a circle In the notice area, we tell you about something that can with a slash through it in damage your vehicle. Many times, this damage would this book. This safety not be covered by your warranty, and it could be costly. But the notice will tell you what to do to help avoid symbol means “Don’t,’’...
Page 7
Vehicle Symbols These are some of the symbols you find on your vehicle. These symbols Here are some These symbols These symbols These symbols For example, have to do with are on some of are used on other symbols these symbols are important your lights: your controls:...
Section 1 Seats and Restraint Systems Manual Front Seat Here you’ll find information about the seats in your vehicle and how to use your safety belts properly. You can also learn about some things you should not do with air bags and safety belts. CAUTION: Seats and Seat Controls You can lose control of the vehicle if you try to...
Page 10
2-Way Front Seat Manual Lumbar Support (Option) The bucket seats adjusted forward or rearward by the lever at the front of the seat. Move the seat adjustment lever at the front of seat toward the driver’s door to unlock Slide the seat to If you have this feature, there will be a knob on the where you want it.
Reclining Seatbacks Power Seats (Option) There is lever on the inside of the seat to adjust If you have this feature, there will be a control pad on the the seatback. inboard side of the driver and passenger bucket seats. You can adjust the seatback by lifting the lever.
Page 12
Sitting in a reclined position when your vehicle is in motion can be dangerous. Even if you buckle up, your safety belts can’t do their job when you’re reclined like this. The shoulder belt can’t do its job because won’t be against your body. Instead, it will be in front of you.
unlock the seat by pushing forward on the lever, while Head Restraints pushing down on the seat. Make sure the seatback is Head restraints are fixed on some models and adjustable locked when it is put back in the upright position. on others.
Page 14
The center and rear bench seats be adjusted forward or rearward by the lever at the front of the seat. CAUTION: Move the seat adjustment A safety belt that is twisted or not properly lever at the front of the seat toward the passenger’s side attached won’t provide the protection needed in to unlock it.
Page 15
To raise or lower the center console, press the button between the beverage holders. Only sit in the center seating position when the console is in an upright position. For details about headrests, see “Head Restraints” in this section. To adjust your seatback, pull up on the lever on the lower outside of the seat.
Page 16
Removing the Rear Seats you have a safety belt guide on your seat, pull To remove the rear seats, do the following: the safety belt all the way out through guide. 1. If you are removing the center seat, remove the right lap-shoulder belt.
Page 17
4. Lift up on the seat release latch. The latches are near 5. Lift up on the rear of the seat to remove the seat the floor on the rear legs of the seat. To relieve assembly from the rear latch pins. Then, pull back pressure on the latch, pull back on the seat.
Page 18
Replacing the Rear Seats To replace the rear seats, do the following: 2. Pull the seat down to latch the rear retainers. Make sure the seat is locked in by pulling up and down on the seat. 1. Lower the seat into position. Make sure the front 3.
Safety Belts: They’re for Everyone 4. If you are replacing the center seat, connect the right lap-shoulder belt to the attachment on the seat This part of the manual tells you how to use safety belts cushion. If you have a safety belt guide on your seat, properly.
Why Safety Belts Work Your vehicle has a light that comes on as a reminder to When you ride in or on anything, you go as fast it goes. buckle up. (See “Safety Belt Reminder Light” in the Index.) In most states and Canadian provinces, the law says to wear safety belts.
Page 21
Get it up to speed. Then stop the vehicle. The rider Put someone on it. doesn't stop. 1-13...
Page 22
The person keeps going until stopped by something. or the instrument panel In a real vehicle, it could be the windshield 1-14...
Page 23
Here Are Questions Many People Ask About Safety Belts and the Answers e.’ Won’t I be trapped in the vehicle after an accident if I’m wearing a safety belt? You could whether you’re wearing safety belt or not. But you can unbuckle a safety belt, even if you’re upside down.
I’m a good driver, and I never drive far from How to Wear Safety Belts Properly home, why should wear safety belts? Adults in an You may be excellent driver, but if you’re This part is only for people of adult size. accident even one that isn’t your fault -- you and your passengers can be hurt.
Page 25
3. Pick up the latch plate and pull the belt across you. The lap part of the belt should be worn low and snug on Don't let it get twisted. hips, just touching the thighs. In a crash, this applies force to the strong pelvic bones.
Page 26
arrows Shoulder Belt Beight Adjuster move it down, push in at the top of the move the height adjuster to the desired,position. You can Before you begin to drive, move the shoulder belt move the adjuster up just by pushing up on the shoulder adjuster to the height that is right for you.
Page 27
e." What's wrong with this? CAUTION: You can be seriously hurt if your shoulder belt is too loose. In a crash, you would move forward too much, which could increase injury. The shoulder belt should fit against your body. The shoulder belt is too loose. It won't give nearly as much protection this way.
Page 28
What’s wrong with this? CAUTION: You can be seriously injured if your belt is buckled in the wrong place like this. In a crash, the belt would go up over your abdomen. The belt forces would be there, not at the pelvic bones.
Page 29
What's wrong with this? CAUTION: You can be ser rsly injured if your belt goes over an armrest like this. The belt would be much too high. In crash, you can slide under the belt. The belt force would then be applied abdomen, not at the pelvic bones, and that could cause serious or fatal injuries.
Page 30
What's wrong with this? You can be seriously injured if you wear the shoulder belt under your arm. In crash, your body would move too far forward, which would increase the chance of head and neck injury. Also, the belt would apply too much force to the ribs, which aren't as strong as shoulder bones.
Page 31
Q.’ What’s wrong with this? CAUTION: You can be seriously injured by a twisted belt. In a crash, you wouldn’t have the full width of the belt to spread impact forces. If a belt is twisted, make it straight so it can work properly, or ask your dealer to fix it.
Your vehicle has two air bags -- one air bag driver and another air bag for the right front passenger. Here are the most important things to know about the air bag system: You can be severely injul Alled in -rash if you aren’t wearing your safety belt even if you...
Page 33
There is an air bag readiness light on the CAUTION: instrument panel, which shows AIR BAG. Air bags inflate with great force, faster than the blink of an eye. If you’re too close to an inflating air bag, it could seriously injure you. Safety belts help keep you in position an air bag inflation in a crash.
Page 34
How the Gir Bag System Works The right front passenger’s air bag is in the instrument panel on the passenger’s side. Where is the air bag? ’he driver’s bag.is in the middle of the steering wheel. 1-26...
Page 35
it can be somewhat above or below,this range. If your vehicle strikes something that will move or deform, such as a parked car, the threshold level will be higher. The air bag is not designed to inflate in rollovers, side Don’t put anything on, or attach anything to, the impacts or rear impacts, because inflation would steering wheel or instrument panel.
Page 36
How does an air bag restrain? inflation will not prevent the driver from seeing or from being able to steer the vehicle, nor will it stop people In moderate to severe frontal or near-frontal collisions, from leaving the vehicle. even belted occupants can contact the steering wheel or the instrument .panel.
Servicing Your Air Bag-Equipped Vehicle Your vehicle is equipped with a crash sensing and diagnostic module, which records information about Air bags affect how your vehicle should be serviced. bag system. The module records information There are parts of the air bag system in several places about the readiness of the system, when the sensors are around your vehicle.
Adding Equipment to Your Safety Belt Use During Pregnancy Air Bag-Equipped Vehicle Safety belts work for everyone, including pregnant women. Like all occupants, they are more likely to be push bumper or If I add bicycle rack to the seriously injured if they don’t wear safety belts. front of my vehicle, will it keep the air bags from working properly? As long as the push bumper or bicycle rack is...
The best way to protect the fetus is to protect the Rear Seat Outside Passenger Positions mQther. When a safety belt is worn properly, it’s more likely that the fetus won’t be hurt in a crash. For pregnant women, as for anyone, the key to making safety belts effective is wearing them properly.
Page 40
If the belt stops before it reaches the buckle, tilt the 1. Pick up the latch plate and pull the belt across you. latch plate and keep pulling until you can buckle it. Don’t let it get twisted. Pull up on the latch plate to make sure it is secure. 2.
Page 41
3. To make the lap part tight, pull down on the buckle The lap part of the belt should be worn low and snug on end of the-belt as.you pull up on the shoulder part. the hips, just touching the thighs. In a crash, this applies force to the strong pelvic bones.
Center Passenger Position CAUTION: (Bench Seat) You can be seriously hurt if your shoulder belt too loose. In a crash, you would move forward too much, which could increase injury. The shoulder belt should fit against your body. Lap Belt If your vehicle has rear bench seats, someone can sit in the center positions.
Page 43
When you sit in a center seating position, you have a lap To make the belt shorter, pull its free end as shown until safety belt, which has no retractor. To make the belt the belt is snug. longer, tilt the latch plate and pull along the belt.
Rear Safety Belt Comfort Guides for Children and Small Adults Your vehicle may have rear shoulder belt comfort guides. This feature will provide added safety belt comfort for children who have outgrown child restraints and for small adults. When installed on a shoulder belt, the comfort guide pulls the belt away from the neck and head.
Page 45
3. Be sure that the belt is not twisted and it lies flat. 2. Slide the guide under and past the belt. The elastic The elastic cord must be under the belt and the cord must be under belt. Then, place the guide guide on top.
Children Everyone in vehicle needs protection! That includes infants and all children smaller than adult size. In fact, the law in every state in the United States and in every Canadian province says children up to some age must be restrained while in a vehicle.
Page 47
CAUTION: (Continued) in a heavy you can’t hold it. For example, crash at only 25 mph (40 km/h), a 124b. (5.5 kg) baby will suddenly become a 240-1b. (110 kg) force on your arms. The baby would be almost impossible to hold.
Page 48
Smaller Children and Babies (Cargo Vans) CAUTION: A very young child's hip bones are so small that a regular belt might not stay low on the hips, as it should. Instead, the belt wiil likely be over the child's abdomen. In a crash, the belt would apply force right on the child's abdomen, which could cause serious fatal injuries.
Where to Put the Restraint CAUTION: (Continued) (Except Cargo Vans) Accident statistics show that children are safer if they heavy you can’t hold it, For example, in a crash are restrained in the rear rather than the front seat. We at km/h), at only 25 mph (40 a 12-1b.
secure any Keep in mind that unsecured child restraint move the vehicle. Be sure to properly child around in a collision sudden stop and injure people restraint in your vehicle even when no child is in it. in the vehicle. Be sure to properly secure any child Top Strap even when no child is in it.
Securing a Child Restraint in a Rear Outside Seat Position You'll be using the lap-shoulder belt. See the earlier part about the top strap if the child restraint has one. 1. Put the restraint on the seat. Follow the instructions Tilt the latch plate to adjust the belt if needed.
Page 52
4. Buckle the belt. Make sure the release button is 5. To tighten the belt, pull up on the shoulder belt while positioned so you would be able to unbuckle the you push down on the child restraint. safety belt quickly if you ever had to. 6.
Page 53
Securing a Child Restraint in a Center Seat Position (Bench Seat) You’ll be using the lap belt. See the earlier part about the top strap if the child restraint has one. 1. Make the belt as long as possible by tilting the latch plate and pulling it along the belt.
To remove the child restraint, just unbuckle the vehicle’s to work safety belt. It will be ready for an adult or larger child passenger. Securing a Child Restraint in the Right Front Seat Position 5. Buckle the belt. Make sure the release button is positioned so you would be able to unbuckle the Your vehicle has front passenger air bag.
Page 55
4. Pick up the latch plate, and run the lap and shoulder portions of the vehicle’s safety belt through or around the restraint. The child restraint instructions will show you how. A ch a rear-fac lg child ;traint can be If the shoulder belt goes in front of the child’s face or seriously injured if the front passenger’s air bag neck, put it behind the child restraint.
Page 56
6. Pull the rest of the lap belt all the way out of the 7 . To tighten the belt, feed the lap belt back into the retractor while you push down on the child restraint. retractor to set the lock. 8.
If you have the choice, a child should sit next to a Larger Children window the child can wear a lap-shoulder belt and get the additional restraint a shoulder belt can provide. Accident statistics show that children are safer if they are restrained in the rear they...
Page 58
CAUTION: Never do this. Here two children are wearing the same belt. The belt can’t properly spread the impact forces. crash, the two children can be crushed together and seriously injured. A belt must be used by only one person at a time. child is wearing a lap-shoulder belt, What if but the child is so small that the shoulder belt is...
in a crash the child might slide under the belt. The belt’s force would then be applied right on the child’s abdomen. That could cause serious or fatal injuries. Wherever the child sits, the lap portion of the belt should be worn low and snug on the hips, just touching the child’s thighs.
Checking Your Restraint Systems Now and then, make sure the safety belt reminder light and all your belts, buckles, latch plates, retractors and anchorages are working properly. Look for any other loose or damaged safety belt system parts. If you see anything that might keep a safety belt system from doing its job, have it repaired.
Section 2 Features and Controls Here you can learn about the many standard and optional features on your vehicle, and information on starting, shifting and braking. Also explained are the instrument panel and the warning systems that tell you if everything is working properly -- and what to do if you have problem.
Page 62
This vehicle has one When a new vehicle is delivered, the dealer provides the double-sided key for the owner with a pair of identical keys and a bar-coded tag. ignition and door locks. It The bar-coded tag has a code on it that tells your dealer will fit with either side up.
Rear Doors Front Doors To open the front side door from the outside, grasp the If you have the Dutch doors, you must open the handle and pull the door open. hatch first. To open the front side door To open the rear doors from from the inside, pull the the outside, open the lever toward you and push...
Page 64
To open the driver’s side To fully open the rear doors, rear door. pull on the latch push in on the clip and lift ‘ I release handle in the inside the check assembly up off of the door. the mounting bracket. Do this on each door.
To unlock your door from the outside, use your key. Door Locks To lock the front doors and sliding side door from the CAUTION: inside, slide the lock levers down. To unlock the front doors and the sliding side Unlocked doors can be dangerous. door from the inside, slide Passengers especially children...
Power Door Locks Every vehicle with power door locks has a pulse lock system. A pulse lock system works like this: If your vehicle has power If the sliding door is open and you press the power door door locks, press the power lock switch, the sliding door will not lock immediately.
Keyless Entry System Check the distance. You may be too far from your vehicle. This product has a maximum range. If your vehicle has this option, you can lock and unlock Check the location. Other vehicles or objects may be your doors or unlock your trunk from up to 30 feet (9 m) blocking the signal.
Matching Transmitter(s) To Your Vehicle To open the housing: Each key chain transmitter is coded to prevent another transmitter from unlocking your vehicle. If transmitter is lost or stolen, a replacement can be purchased through your dealer. Remember to bring any remaining transmitters with you when you go to your dealer.
Sliding Door To close the sliding side door, pull the handle toward the front to release the rear latch, and slide the door forward. To open the sliding side door, pull the handle toward the back and slide the door to the rear until latches in the open position.
Page 70
Sliding Door Child Security Lock This feature prevents passengers from opening the sliding side door from the inside. Your vehicle’s sliding side To use this feature, do the following: door is equipped with 1. Move the lever all the way up. (Arrow is pointing to child security door lock, the lever that you must move.) located at the rear of the...
Page 71
Rear Hatch and Dutch Doors Release Hatch (Option) If you have this option, your vehicle must be in either CAUTION: PARK (P) or NEUTRAL (N) to release the hatch and unlock the Dutch doors. If your battery is dead, the It can be dangerous to drive with the rear even hatch and Dutch doors will not open,...
To release the hatch using the optional Keyless Entry Theft hand-held transmitter, see “Keyless Entry System” in Vehicle theft is big business, especially in some cities. the Index. Although your vehicle has a number of theft-deterrent features, we know that nothing we put on it can make To release the hatch and it impossible to steal.
New Vehicle “Break-In” Parking at Night Park in a lighted spot, close all windows and lock your vehicle. Remember to keep your valuables out of sight. NOTICE: Put them in storage area, or take them with you. Parking Lots Your modern vehicle doesn’t need an elaborate “break-in.”...
Ignition Positions NOTICE: Use your ignition key to start your vehicle. The ignition key lets you turn the ignition switch to five different positions. Don’t operate accessories in the ACCESSORY position for long periods of time. Prolonged operation of accessories in the ACCESSORY position could drain your battery and prevent you from starting your vehicle.
NOTICE: NOTICE: Don’t try to shift to PARK (P) if your vehicle is If your key seems stuck in LOCK and you can’t in. If moving. If you do, you could damage the turn it, be sure it is all the way it is, then transmission.
2. If it doesn’t start right away, hold your key in Fuel Regulator START. If it doesn’t start in 10 seconds, push the You have a fuel regulator that shuts the fuel off when the accelerator pedal all the way down for five more engine reaches 5,600 rpm.
Page 77
4. After you’ve used the coolant heater, be sure to store To use the coolant heater: the cord as was before to keep it away from moving Turn off the engine. engine parts. If you don’t, it could be damaged. 2.
Automatic Transmission Operation CAUTION: (Continued) There several different positions for your shift lever. Don’t leave your vehicle when the engine running unless you have to. If you have left the .engine running, the vehicle can move suddenly. You or others could be injured. To be sure your vehicle won’t move, even when you’re on fairly level ground, always set your parking brake and (P).
Page 79
REVERSE (R): Use this gear to back up. CAUTION: NOTICE: Shifting out of PARK (P) or NEUTRAL (N) while your engine is “racing” (running at high speed) Shifting to REVERSE (R) while your vehicle is dangerous. Unless your foot is firmly on the moving forward could damage your transmission.
Page 80
(D): DRIVE This position is for normal driving. If you FIRST (1): This position gives you even more power need more power for passing, and you’re: (but lower fuel economy) than SECOND (2). You can use it on very steep hills, or in deep snow or mud. If the Going less than about 35 mph (56 km/h), push your selector lever is put in FIRST (1)’...
Parking Brake Locking Rear Axle To set the parking brake, hold the regular brake pedal If you have this feature, your rear axle can give you down with your right foot. additional traction on snow, mud, ice, sand or gravel. It works like a standard axle most of the time, but when Push down the parking brake pedal with your left foot.
Shifting Into PARK (P) NOTICE: CAUTION: Driving with the parking brake on can cause your rear brakes to overheat. You may have to replace them, and you could also damage other It can be dangerous to get out of your vehicle if parts of your vehicle.
Page 83
2. Move the shift lever into the PARK (P) position like this: Move the lever up far as it will go. 3. Turn the ignition key to LOCK. Pull the lever toward you. 4. Remove the key and take it with you. If you can remove the key from your ignition, your vehicle is in PARK (P).
Leaving Your Vehicle With the Torque Lock E.noiqe Rmnnjnq If you parking on hill and you don’t shift your transmission into PARK (P) properly, the weight of the vehicle may put too much force on the parking pawl in the transmission. You may find it difficult to pull the shift lever out of PARK (P).
Shifting Out of PARK (P) Parking nvPr T h i q Your vehicle has a brake-transmission shift interlock. You have to fully apply your regular brake before you can shift from PARK (P) when the ignition is in the RUN position. See “Automatic Transmission” in the Index.
Engine Exhaust Running Your Engine While You’re Parked It’s better not to park with the engine running. But if you CAUTIOF: ever have to, here are some things to know. Engine exhaust can kill. It contains the gas carbon monoxide (CO), which you can’t see or CAUTION: smell.
Power Windows CAUTION: It can be dangerous to get out of your vehicle if the shift lever is not fully in PARK (P) with the parking brake firmly set. Your vehicle can roll. Don’t leave your vehicle when the engine is running unless you have to.
Exprer- ’ wn Window The driver s window switch also has an “express” feature that allows it to lower without holding the window switch. Hold the driver’s window switch down It can be dangerous to drive with the rear for more than 112 second to activate the express-down swing-out windows, rear hatch or rear doors feature.
Horn Turn' SignaVMultifunction Lever To sound the horn, press the horn symbols on the steering wheel. Tilt Wheel (Option) The lever on the driver's side of the steering column includes your: Turn and Lane Change Signals A tilt steering wheel allows you to adjust the steering wheel before you drive.
Turn and Lane Change Signals If a bulb is burned out, replace it to help avoid accident. If the arrows don’t go on at all when you The turn signal has two upward (for right) and two signal turn, check the fuse (see “Fuses and Circuit downward (for left) positions.
Windshield Washer Windshield Winers At the top of the multifunction lever, there's paaale You control the windshield marked with the windshield washer symbol and PUSH. To wipers by turning the band spray washer fluid on the windshield, press the paddle. with the wiper symbol on it.
Rear Window Washermiper (Option) the washer bottle, you may not be able to wash your rear window. If you can wash your windshield, but not your rear window, check the fluid level. Cruise Control (Option) from switch on your instrument panel, next to With cruise control, you can maintain a speed of about the audio system.
Page 93
Resuming a Set Speed Setting Cruise Control Suppose you set your cruise control at desired speed and then you apply the brake. This, of course, shuts the cruise control. But you don't need to reset it. Once you're going about If you leave your cruise control switcn on when 25 mph (40 km/h) or more,...
Page 94
Increasing Speed While Using Cruise Control Passing Another Vehicle While Using Cruise Control There are two ways to go to a higher speed: Use the accelerator pedal to increase .your speed. When you take your foot off the pedal, your vehicle will slow Use the accelerator pedal to get to the higher speed.
Page 95
Turn the knob to the master lamp symbol to turn on all Lamps the lamps listed as well as the headlamps. Turn the knob to to turn your lamps. Rotate the dial next to the lamp switch down to dim your instrument panel lights.
When it begins to get dark, your DRL indicator light is a Headlamps On Reminder reminder to turn your headlamp switch on. The other A reminder tone will sound when your headlamps or lamps that come on with your headlamps will also parking lamps turned on and your ignition is in the come on.
Dome Lam- Off Button Interior Lamps Dome Lamps ::.,,, If the DOME LAMP OFF button is in the out position, your interior lamps will work as usual. The dome lamps may come on when you open any of the doors. You can also turn on the dome lamps by turning the dimmer dial up until clicks.
Page 98
If the button is pressed in, the interior lamps will not Mirrors come on when any of the vehicle’s doors are open, unless your vehicle has the optional Keyless Entry Inside Daymight Rearview Mirror system. The button is located next to the lamp switch knob.
you do not accidentally move a mirror, turn the knob to Outside Mirrors the middle (off‘) position. Adjust your outside mirrors so you can just see the side out. Push the mirror Mirrors can also be folded in of your vehicle. toward the vehicle to move it in.
Storage Compartments If you have an optional sliding tray storage compartment, is under front passenger seat. To open the Your front storage compartment/glove box is at the compartment, move the latch in the top handle and pull the tray forward. center of the engine cover.
Page 101
If you have rear storage compartments, pull up on the lid There is also a maphtorage pocket on the passenger's side of the engine cover console. to open the cover, 2-41...
Page 102
Overhead Console (Option) Reading Lamps Press the button near each lamp to turn the reading lamps on and off. The lamps can also be swiveled to point in the direction you want. 2-42...
Page 103
Center the garage door opener activation button over Installing a Garage Door Opener the console door button and press the opener firmly If you have a garage door opener, the front overhead into place. compartment can be used to conveniently store the opener.
Page 104
Now, with the compartment Temperature and Compass Display door closed, press the button again to make sure the garage door opener operates properly. With the garage door opener positioned properly and the right number of pegs in place, you should only have to press the button slightly to operate the opener.
Page 105
Turn the display on or off 'by pressing the ON/OFF switch. Display the temperature in either degrees Fahrenheit (English) or Celsius (metric) by pressing the USMET switch. Before you turn on the ignition and move the vehicle, the temperature indicated will be the last outside temperature recorded with the ignition on.
Sunglasses Storage Compartment Convenience Net (Option) The console has a sunglasses storage compartment. You may have a convenience net in the rear of your vehicle to help keep small loads, like grocery bags, in place during sharp turns or quick stops and starts. The net is not designed for larger, heavier items.
Luggage Carrier (Option) NOTICE: If you have a luggage carrier, you can load things on top of your vehicle. Loading cargo that weighs more than 200 lbs. The luggage carrier has slats, side rails and crossrails (91 kg) on the luggage carrier may damage your attached to the roof to secure cargo.
Page 108
Ashtl- ys and Cigarette Lighter To remove the front ashtray, open it and gently pull it slightly past its stop. The cigarette lighter is on the left of the engine To remove the ashtray on the sliding door, open it, press cover console.
Accessory Power Outlets (Option) Sun Visors If you have accessory power outlets, you can plug in To block out glare, you can swing down the visors. You can also swing them from side to side. Your visors may have auxiliary electrical equipment. Just pull up from the an extension that can be pulled out for additional glare bottom of the door and follow the proper installation protection and a strap for holding small items, such as maps.
Page 111
K. Rear Heater Control Lamp Switches Instrument Panel Dimmer L. Rear WasherNiper M. Front Ashtray Multifunction Lever Hazard Lamp Switch N. Accessory Power Outlets 0. Cupholders/Storage Tray Transmission Shift Lever Ignition Switch P. Front Storage Compartment Rear Hatch Release Q. Audio System Rear Defogger R.
Instrument Panel Cluster Your instrument panel cluster is designed to let you know at a glance how your vehicle is running. You’ll know how fast you’re going, about how much fuel remains, and many other things you’ll need to know to drive safely and economically.
Warning Lights, Gages and Indicators Speedometer and Odom. er Your speedometer lets you see your speed in both miles This part describes the warning lights and gages that may per hour (mph) and kilometers per hour (km/h). Your your vehicle. The pictures will help locate them.
Safety Belt Reminder Light Air Bag Readiness Light When the key is turned to RUN or START, tone will There is an air bag readiness light on the instrument come on for about eight seconds to remind people to panel, which shows AIR BAG.
Page 115
Voltmeter Charging System Indicator Light When your engine is not The charging system light will come briefly when running, but the ignition is on (in the position), you turn the ignition on, but the engine is not running, as the gage shows your a check to show you the battery’s state of charge j-+l...
Brake System Warning Light Readings in the low warning zone may occur when large number of electrical accessories are operating in Your vehicle’s hydraulic brake system is divided into the vehicle and the engine is left at an idle for an two parts.
If the light comes on while you are driving, pull off the Anti-Lock Brake System Warning Light road and stop carefully. You may notice that the pedal is With the anti-lock brake harder to push. Or, the pedal may go closer to the floor. system, this light will come It may take longer to stop.
Page 118
Malfunction Indicator Lamp NOTICE: (Service Engine Soon Light) Your vehicle is equipped If you keep driving your vehicle with this light with a computer which on, after a while, your emission controls may not monitors operation of the work as well, your fuel economy may not be as fuel, ignition and emission SERVICE good and your engine may not run as smoothly.
Page 119
If the Light Is On Steady If the Light Is Flashing You may be able to correct the emission system The following may prevent more serious damage to malfunction by considering the following: your vehicle: Did you just put fuel into your vehicle? Reduce vehicle speed.
Have you recently changed brands of fuel? Oil Pressure Gage sure to fuel your vehicle with quality fuel (see The oil pressure gage shows “Fuel” in the Index). Poor fuel quality will cause your the engine oil pressure in engine not to run as efficiently as designed. You may psi (pounds per square inch) notice this as stalling after start-up, stalling when you when the engine is running.
Page 121
Check Oil Light CAUTION: This light should come on briefly while you are starting your engine. If the Don’t keep driving if the oil pressure is low. If light doesn’t come on, have your engine can become so hot that it CHECK it repaired.
Engine Coolant Temperature Gage Daytime Running. Lamps, Indicator Light your vehicle’was first the gage pointer moves to :::O sold, when new, in Canada, the red area, your engine is too hot! you will have this light on the instrument panel. It means that your engine coolant has overheated.
Page 123
Fuel Gage Check Gages Light The fuel gage tells you This light will come on how much fuel you have remaining when the ignition is on. CHECK GAGES If the light comes on and stays on while you are driving, When the gage fust indicates EMPTY (E), you still have a little fuel left, but you should get more fuel as soon as possible check your various gages to see if they are in the...
Section 3 Comfort Controls and Audio Systems In this section you’ll find out how to operate the comfort Heating/Air Conditioning System control and audio systems offered with your vehicle. Be sure to read about the particular systems supplied with your vehicle. Comfort Controls This section tells you how to make your air system work for you.
Page 126
I , . Fan Knob BI-LEVEL: This setting brings in outside air This control has four positions. increase airflow, through the heater floor vent and the instrument panel HI. To turn the knob toward decrease airflow, move it vents. If you move the temperature knob between hot toward LO.
Function Knob Heating System This knob is next to the temperature knob. The function knob allows you to choose the direction of air delivery. OFF: This setting turns the system off. VENT The air comes out at the vents on y instrument panel.
Page 128
Rear Heating System (Option) Rear Air Conditioning System (Option) You may have the optional rear heater. The three-speed You may have rear air conditioning. The rear air fan switch is to the right of the radio. Turn the switch conditioning switch is located to right of the heater toward HIGH for higher airflow in the rear area.
The rear air conditioning system will only send cooled Air Conditioning air if the front system is on. It can still be used to Before using your vehicle’s air conditioning, open the circulate air, even if the front system is off. windows to clear the vehicle of hot air.
Defrosting Use DEFROST to remove fog or ice from the windshield quickly in extremely cold conditions. The temperature knob should be in the red area and the fan control toward high. The air conditioning compressor may operate in this setting to dehumidify the air. The BLEND setting is useful for cold weather with a large number of passengers or very humid conditions to help keep the windshield clear.
Rear Window Defogger (Option) If you have rear heating or rear air conditioning, you will have adjustable vents in the rear of the vehicle to If your vehicle has this option, the rear window will help direct the airflow. The rear air conditioning vents have lines running across the glass.
You can turn the defogger off at any time by pressing Setting the Clock for AM-FM Stereo and the button again. The defogger will shut itself off after AM-FM Stereo with Cassette Tape Player several minutes so that the elass does not eet too hot. If Press SET.
Page 133
AM-FM Stereo Finding Station AM-FM: F M . Press the lower knob to get AM or TUNE: Turn this knob to tune in radio stations. SEEK: Press the right arrow to. tune to the next higher station and the left arrow to tune to the next lower station and stay there.
In addition to the four stations set as above, up to AM-FM Stereo with Cassette Tape Player three additional stations may be preset on each band by (Option) pressing two adjoining buttons at the same time. Just: 1. Tune in the desired station. 2.
Page 135
3. Press two adjoining buttons at the same time, Finding a Station within five seconds. Whenever you press the same AM-FM: Press the lower knob to get AM or FM. two buttons, the station you set will return. TUNE: Turn this knob to tune in radio stations. 4.
Playing a Cassette Tape AM-FM Stereo with Cassette Tape and Automatic Tone Control (Option) Your tape player is built to work best with tapes that are 45 minutes long on each side. Tapes longer than that are so thin they may not work well in this player. Once the tape is playing, use the knobs for VOLUME, FADE and BAL just as you do for the radio.
Page 137
AUTO TONE: Press this button to select among the SCV: This is the Speed-Compensated-Volume (SCV) five preset equalization settings and tailor the sound to knob. Move the control ring behind the PWR-VOL knob the music or voice being heard. Each time you press clockwise to adjust the SCV.
Page 138
P.SCAN: The preset scan button lets you scan through Adjusting the Speakers your favorite stations stored on your pushbuttons. Select BAL: Press this button to remove the control from its either the AM, FMl or mode then press stored position. Turn the control clockwise to adjust €?SCAN.
Page 139
to reduce cassette tape noise. (5): Press this button Once the tape is playing, use the VOL, BAL, FADE, The double-D symbol will appear on the display while TREB and BASS controls just as you do for the radio. the player is in this mode. direction arrow will be on the The tape symbol and display whenever...
CLN: This message may appear on the display. If AM-FM Stereo with Compact Disc Player does, your cassette tape player needs to be cleaned. It and Automatic Tone Control (Option) will still play tapes, but you should clean it as soon as possible to prevent damage to your tapes and player.
Page 141
SCAN: Press and hold SEEK for two seconds until SCV: This is the Speed-Compensated-Volume (SCV) SCAN appears the display. SCAN allows you to knob. Move the control ring behind the PWR-VOL listen to stations for a few seconds. The receiver will knob clockwise to adjust the SCV.
Page 142
P.SCAN: The preset scan button lets you scan through BASS: Press lightly on this knob to release it from its your favorite stations stored on your pushbuttons. Select stored position. Turn the knob clockwise to increase the or FM2 mode and then press either the AM, bass and counterclockwise decrease the bass.
Page 143
RECALL: Press this button to see what track is Playing a Compact Disc playing. Press it again within five seconds to see how PWR: Press this knob to turn the system on. long the CD has been playing that track. Elapsed time is (Please note that you can also turn the system on displayed in minutes and tenths of second.
FWD (6): Press and hold this button to advance rapidly Playing a Cassette in the Remote Cassette within a track. You will hear the disc selection play at Tape Player (Option) high speed while you press the FWD button. This allows you to listen and find out when the disc is at the desired selection.
Page 145
(4): Press this button to rapidly reverse the tape. Once the tape is playing, use the control knobs for VOL, The tape will rapidly reverse to the beginning of the AUTO TONE, BAL, FADE, TREB and BASS just as cassette reel or until you press REV again. The radio you do for the radio.
Page 146
SEEK: Rear Seat Audio (Option) Press the up arrow tune to’the next higher station (with enough strength) and stay there. Press the down arrow to tune to the next lower station (with enough strength) and stay there. The sound will mute while seeking.
Theft-Deterrent Feature P.SET PROG: The front passengers must be listening to something different for each of these three functions THEFTLOCK" is designed to discourage theft of your to work: radio. It works by using a secret code to disable all radio Press this button to seek through your preset radio functions whenever battery power is removed.
Page 148
Activating the Theft-Deterrent Feature 5 . Press MN and 000 will appear on the display. The instructions which follow, explain how to enter your 6. Press MN again to make the last two digits agree secret code to activate the THEFTLOCK system. It is with your code.
Page 149
1. Turn the ignition to the ACCESSORY or Unlocking the Theft-Deterrent Feature After a RUN position. Power Loss 2. Turn the radio off. Enter your secret code as follows; pause no more than 15 seconds between steps: 3. Press the 1 and 4 buttons together. Hold them down until SEC shows on the display.
Understanding Radio Reception help avoid hearing loss or damage: Adjust the volume control to the lowest setting. Stereo Increase volume slowly until you hear comfortably stereo will give you the best sound. But signals and clearly. will reach only about 10 to 40 miles 16 to 65 km).
Care of Your Cassette Tape Player Cleaning may be done with a scrubbing action, non-abrasive cleaning cassette with pads which scrub A tape player that is not cleaned regularly can cause the tape head as the hubs of the cleaner cassette turn. It reduced sound quality, ruined cassettes or a damaged is normal for the cassette to eject while cleaning.
Page 152
Care of Compact Discs Your Fixed Mast Antenna them in Handle discs carefully. Store their original cases The fixed mast antenna can withstand most car washes or other protective cases and away from direct sunlight without being damaged. If the mast should ever become and dust.
Section 4 Your Driving and the Road Defensive Driving The best advice anyone can give about driving is: Drive defensively. Please start with a very important safety device in your vehicle: Buckle up. (See “Safety Belts’’ in the Index.) Defensive driving really means “be ready for anything.” On city streets, rural roads or freeways,“it means “always expect the unexpected.”...
Drunken Driving The obvious way to solve this highway safety problem is for people never drink alcohol and then drive. Death and injury associated with drinking and driving But what if people do? How much is “too much” if the is a national tragedy.
Page 157
Since alcohol is carried in body water, this means that woman generally will reach a higher BAC level than man of her same body weight when each has the same number of drinks. The law in many U.S. states sets the legal limit at a BAC of 0.10 percent.
Page 158
The body takes about an hour to rid itself of the alcohol in one drink. No amount of coffee or number of cold showers will speed that up. “I’ll be careful” isn’t the right answer. What if there’s an emergency, a need to Drinking and then driving is very dangerous.
Braking Control of a Vehicle Braking action involves perception time and You have three systems that make your vehicle go where reaction time. you want it to go. They are the brakes, the steering and the accelerator. All three systems have to do their work First, you have to decide to push the brake pedal.
Anti-Lock Brakes Avoid needless heavy braking. Some people drive in spurts heavy acceleration followed by heavy Your vehicle has anti-lock brakes (ABS). ABS is an braking rather than keeping pace with traffic. This advanced electronic braking system that will help is a mistake.
Page 161
The anti-lock system can change the brake pressure faster than any driver could. The computer is programmed to make the most of available tire and road conditions. Here’s how anti-lock works. Let’s say the road is wet. You’re driving safely. Suddenly an animal jumps out in front of you.
Remember: Anti-lock doesn’t change the time need Steering Tips to get your foot up to the brake pedal or always decrease stopping distance. If you get too close to the vehicle in Driving on Curves front you, you won’t have time to apply your brakes It’s important to take curves at a reasonable speed.
Speed limit signs near curves warn that you should adjust your speed. Of course, the posted speeds are based on,good weather and road conditions. Under less favorable conditions you’ll want to go slower. If you need to reduce your speed as you approach a curve, do it before you enter the curve, while your front wheels are straight ahead.
Off-Road Recovery Passing You may find sometime that your right wheels have The driver of vehicle about to pass another on a dropped off the edge of road onto the shoulder while two-lane highway waits for just the right moment, you’re driving.
Page 165
Check your mirrors, glance over your shoulder and Do not get too close to the vehicle you want to start your left lane change signal before moving out pass while you’re awaiting an opportunity. For one of the right lane to pass. When you are far enough thing, following too closely reduces your area of ahead of the passed vehicle to see its front in your vision, especially if you’re following a larger...
Loss of Control If your vehicle starts to slide, ease your foot off the accelerator pedal and quickly steer the way you want the Let’s review what driving experts say about what vehicle to go. If you start steering quickly enough, your happens when the three control systems (brakes, steering vehicle may straighten out.
Adjust your inside rearview mirror to reduce the Driving at Night glare from headlamps behind you. Since you can’t see well, you may need to slow down and keep more space between you and other vehicles. Slow down, especially on higher speed roads. Your headlamps light up only so much road ahead.
You can be temporarily blinded by approaching Driving in Rain and on Wet Roads headlamps. It can take a second or two, or even several seconds, for your eyes to readjust to the dark. When you are faced with severe glare (as from a driver who doesn’t lower the high beams, or a vehicle with misaimed headlamps), slow down a little.
Page 169
Driving too fast through large water puddles or even The heavier the rain, the harder is to see. Even if your going through some car washes can cause problems, too. windshield wiper blades are in good shape, heavy rain The water may affect your brakes. Try to avoid puddles. can make harder to see road signs and traffic signals, But if you can’t, try to slow down before you hit them.
Hydroplaning Driving Through Deep Standing Water Hydroplaning is dangerous. So much water can build up under your tires that they can actually ride the water. NOTICE: This can happen if the road is wet enough and you’re going fast enough. When your vehicle is hydroplaning, If you drive too quickly through deep puddles it has little or no contact with the road.
One of the biggest problems with city streets is the City Driving amount of traffic on them. You’ll want to watch out for what the other drivers are doing and pay attention to traffic signals. Here are ways to increase your safety in city driving: Know the best way to get to where you are going.
The most important advice on freeway driving is: Keep Freeway Driving up with traffic and keep to the right. Drive at the same speed most of the other drivers are driving. Too-fast or too-slow driving breaks smooth traffic flow. Treat the left lane on a freeway as a passing lane.
Is your vehicle ready for a long trip? If you keep Once you are moving on the freeway, make certain you serviced and maintained, it’s ready to go. If it needs allow a reasonable following distance. Expect to move service, have it done before starting out. Of course, slightly slower at night.
Highway Hypnosis Hill and Mountain Roads Is there actually such condition as “highway hypnosis”? Or is it just plain falling asleep at the wheel? Call it highway hypnosis, lack of awareness, or whatever. There is something about an easy stretch of road with the same scenery, along with the hum of the tires on the road, the drone of the engine, and the rush of the wind against the vehicle that can make you sleepy.
Page 175
If you drive regularly in steep country, or if you’re planning to visit there, here are some tips that can make your trips safer and more enjoyable. Keep your vehicle in good shape. Check all fluid NEUTRAL Coas ,g downhill in or with the levels and also the brakes, tires, cooling system and ignition off is dangerous.
Page 176
Here are some tips for winter driving: Have your vehicle in good shape for winter. You may want to put winter emergency supplies in your vehicle. 4-22...
Page 177
Whatever the condition -- smooth ice, packed, blowing or loose snow -- drive with caution. Accelerate gently. Try not to break the fragile traction. If you accelerate too fast, the drive wheels will spin and polish the surface under the tires even more. Your anti-lock brakes improve your vehicle’s stability when you make a hard stop on a...
Tie a red cloth to your vehicle to alert police that If You’re Caught in a Blizzard ’ you’ve been stopped by the snow. Put on extra clothing or wrap blanket around you: If you have no blankets or extrq clothing, make body insulators from newspapers, burlap bags, rags, floor mats anything you can wrap around yourself or...
Page 179
Run your engine only as long as you must. This saves fuel. When you run the engine, make it go a little faster than just idle. That is, push the accelerator slightly. This uses less fuel for the heat that you get and it keeps the Snow can trap exhaust gases under your vehicle.
Loading Your Vehicle The Certificationmire label also tells you the maximum weights for the front and rear axles, called the Gross Axle Weight Rating (GAWR). To find out the actual loads on your front and rear axles, you need to go to a weigh station and weigh your vehicle.
Page 181
Using heavier suspension components to get added durability might not change your weight ratings. Ask your dealer to help you load your vehicle the right way. Things you put inside your vehicle NOTICE: and injure people in a sudden stop turn, or a crash.
Payload If your vehicle comes with the Trailering Package, there is also a load rating which includes the weight of the The Payload Capacity is shown on the Certificationflire vehicle and the trailer it tows. This rating is called the label.
Towing a Trailer NOTICE: CAUTION: Pulling a trailer improperly can damage your vehicle and result in costly repairs not covered by your warranty. pull trailer correctly, follow If you don’t use the correct equipment and drive the advice in this part, and see your dealer properly, you can lose control when you pull a for important information about towing a traile...
If You Do Decide To Pull A Trailer Three important considerations have to do with weight: the weight of the trailer, If you do, here are some important points: the weight of the trailer tongue many There are different laws, including speed limit and the weight on your vehicle’s tires.
Maximum trailer weight is calculated assuming the driver and one passenger are in the tow vehicle and it has all the required trailering equipment. The weight of additional optional equipment, passengers and cargo in the tow vehicle must be subtracted from the maximum trailer weight.
Total Weight on Your Vehicle’s Tires Will you have to make any holes in the body of your vehicle when you install a trailer hitch? If you do, Be sure your vehicle’s tires are inflated to the limit for then be sure to seal the holes later when you remove cold tires.
Driving with a Trailer Trailer Brakes If your trailer weighs more than 1,000 lbs. (450 kg) loaded, then it needs its own brakes and they must be CAUTION: adequate. Be sure to read and follow the instructions for the trailer brakes so you’ll be able to install, adjust and maintain them properly.
Page 188
Towing a trailer requires certain amount of experience. lowing Distance Before setting out for the open road, you’ll want to get as you >ray at least twice far behind the vehicle ahead to know your rig. Acquaint yourself with the feel of would when driving your vehicle without a trailer.
When towing trailer, the green arrows your Making Turns instrument panel will flash for turns even if the bulbs on the trailer are burned out. Thus, you may think drivers NOTICE: behind you are seeing your signal when they are not. It’s important to check occasionally to be sure the trailer bulbs are still working.
Parking on Hills When You Are Ready to Leave After Parking on a Hill Youereally should not park your vehicle, with a trailer on a attached, hill. If something goes wrong, your rig Apply your regular brakes and hold the pedal down could start to move.
BROWN: Rear lamps. Trailer Wiring Harness YELLOW Left stoplamp and turn signal. If you have the optional trailering package, your vehicle will have an eight-wire harness, including the center DARK GREEN: Right stoplamp and turn signal. high-mounted stoplamp battery feed wire. The harness WHITE (Heavy Gage): Ground.
Section 5 Problems on the Road Here you’ll find what to do about some problems that They also let police know you have a problem. Your can occur on the road. front and rear turn signal lamps will flash on and off. Hazard Warning Flashers Press the button down to make your front and rear turn signal lamps flash on and off.
The hazard warning flasher button is located on top of the steering column. CAUTION: To turn off the flashers, press the button down again. Batteries can hurt you. They can be When the hazard warning flashers are on, your turn signals won’t work.
Page 195
3. Turn off the ignition on both vehicles. Unplug 1. Check the other vehicle. It must have a 12-volt unnecessary accessories plugged into the cigarette battery with a negative ground system. lighter or accessory power outlets. Turn off all lamps that aren’t needed as well as radios.
Page 196
5. Check that the jumper cables don’t have loose or missing insulation. If they do, you could get a shock. CAUTION: The vehicles could be damaged too. Before you connect the cables, here are some basic Using a match near a battery can cause battery things you should know.
Page 197
6. Connect the red 8. Now connect the black positive cable to the negative cable to the good battery’s positive terminal of the vehicle with the negative terminal. Don’t let the other end dead battery. touch anything until the next step. The other end of the negative cable doesn’t go to the dead...
10. Now start the vehicle with the good battery and run Towing Your Vehicle the engine for a while. Try to have a GM dealer or a professional towing 11. Try to start the vehicle with the dead battery. If it service tow your vehicle.
Page 199
CAUTION: CAUTION: A vehicle can fall from a car carrier if it isn’t To help avoid injury to you or others: adequately secured. This can cause collision, Never let passengers ride in vehicle that is serious personal injury and vehicle damage. The being towed.
Page 200
When your vehicle is being towed, have the ignition NOTICE: key in the OFF position. The steering wheel should be clamped in a straight-ahead position, with clamping device designed for towing service. Do not If your vehicle has all-wheel drive, do not have use the vehicle’s steering column lock for this.
Page 201
Towing From the Front NOTICE: (Except All-Wheel Drive) Tow Limits -- 35 m p 1 1 (56 krnh), 50 rniles (80 k m ) Do not tow with sling-type equipment or the front bumper system will be damaged. Use wheel-lift or car-carrier equipment. Additional ramping be required for car-carrier equipment.
Page 202
Towing From the Front (All-Wheel Drive) NOTICE: A towing dolly must be used under the rear wheels when towing front the front. Do not tow with sling-type equipment or the front bumper system will be damaged. Use wheel-lift or car-carrier equipment. Additional ramping may be required for car-carrier equipment.
Page 203
Towing From the Rear NOTICE: (Except All-Wheel Drive) not tow with sling-type equipment or the rear bumper system will be damaged. Use wheel-lift or car-carrier equipment. Additional ramping may be required for car-carrier equipment. safety chains and wheel straps. Towing a vehicle over rough surfaces could damage a vehicle.
Page 204
Towing From the Rear (All-Wheel Drive) NOTICE: A towing dolly must be used under the front kheels reaK when towing from the Do not tow with sling-type equipment or the rear bumper system will be damaged. Use wheel-lift or car-carrier equipment. Additional ramping may be required for car-carrier equipment.
Engine Overheating You will find a temperature gage on your vehicle’s instrument panel. Steam from an overheated engine can burn If Steam Is Coming From Your Engine badly, even if you just open the hood. Stay away from the engine if you see or hear steam coming from it.
If No Steam Is Coming From Your Engine If you no longer have the overheat warning, you can drive. Just to be safe, drive slower for about If you get the overheat warning but or hear no minutes. If the warning doesn’t come back on, steam, the problem may not be too serious.
Page 207
If the coolant inside the coolant recovery tank is boiling, When you decide it’s safe to lift the hood, here’s what don’t do anything else until cools down. you’ll see: The coolant level should be at the ADD mark. If it Coolant Recovery Tank isn’t, you may have a leak radiator hoses, heater...
Page 208
How to Add Coolant to the Coolant Recovery Tank If you haven’t found a problem yet, but the coolant level Heater and radiator hoses, and other engine isn’t at the ADD mark, add a 50/50 mixture of clean water (preferably distilled) and DEX-COOL very hot.
Page 209
NOTICE: CAUTION: In cold weather, water can freeze and crack the You can be burned if you spill coolant on hot engine, radiator, heater core and other parts. engine parts. Coolant contains ethylene glycol Use the recommended coolant and the proper and it will burn if the engine parts are hot coolant mix.
Page 210
Steam and scalding liquids from a hot cooling system can blow out and burn you badly. They are under pressure, and if you turn the radiator pressure cap even a little they can come out at high speed. Never turn the cap when the cooling system, including the radiator pressure cap, is hot.
2. Then keep turning How to Add Coolant to the Radiator ,the pressure cap, but 1. You can remove the now push down as you radiator pressure cap when the cooling system, including the radiator pressure cap and upper radiator hose, is no longer hot.
Page 212
Fill the radiator with the proper mix, up to the base 4. Then fill the coolant recovery tank to the ADD mark. of the filler neck. 5. Put the cap back on the coolant recovery tank, but leave the radiator pressure cap off.
Page 213
6. Start the engine and let it run until you can feel the 8. Then replace the pressure cap. At any time during upper radiator hose getting hot. Watch out for the this procedure if coolant begins to flow out of the engine fan.
Engine Fan Noise If a Tire Goes Flat This vehicle has clutched engine cooling fan. When a tire to “blow out” while you’re driving, It’s unusual the clutch is engaged, the fan spins faster to provide your especially if you maintain tires properly.
Changing a Flat Tire If a tire goes flat, avoid further tire and wheel damage by driving slowly to a level place. Turn your hazard warning flashers. ' ! ! ! h CAUTION: Changing tire can cause an injury. The vehicle can slip off the jack and roll over you or other people.
Removing the Spare Tire and Tools The jacking equipment you’ll need is stored by your vehicle’s rear doors, along the passenger side wall. Remove the wheel, blocks by turning the top nut counterclockwise. Remove the nut and washer, then pull the wheel blocks off the bolt.
Page 217
NOTICE: ~~~~~ Never remove or restow a tire frondto a stowage position under the vehicle while the vehicle is supported by a jack. Always tighten the tire fully against the underside of the vehicle when restowing. The ratchet has an UP side. Your spare tire is stored underneath the rear of your vehicle.
Page 218
Attach the ratchet, with the DOWN side facing you, to the extension. The extension has a socket end and flat chisel end. Put the flat end of the extension on an angle through the Turn the ratchet counterclockwise to lower the spare tire hole in the rear door frame, above the bumper.
Page 219
When the tire has been lowered, tilt the retainer at the end of the cable and .pull it through the wheel opening. Pull the tire out from under the vehicle. The tools you’ll be using include the jack (A), wheel NOTICE: blocks (B), extension (C) and ratchet (D).
Page 220
If you have a standard steel wheel, carefully pry along Removing the Wheel Covers the edge of the hub cap until it comes off. Be-carefu1,the may be sharp. You will have to take off hub caps or wheel nut caps to rim edges try to the hub...
Removing the Flat Tire and Installing the Spare Tire 2. With the DOWN side facing you, use the ratchet and socket to loosen all the wheel nuts. Don't remove them yet. Before you start, block the front and rear of the tire The jack has a bolt on the end.
Page 222
Attach the ratchet to the extension with the UP side 6 . Position the jack under the vehicle. facing you. 5. Rotate the ratchet to the right. That will raise the jack lift head little. 5-30...
Page 223
Getting under a vehicle when it is jacked up is dangerous. If the vehicle slips off the jack, you could be badly injured or killed. Never get under a vehicle when it is supported only by jack. NOTICE: Raising your vehicle with the jack improperly 7.
Page 224
Remove any rust or dirt from the wheel bolts, CAUTION: mounting surfaces and spare wheel. Never use oil or grease on studs or nuts. If you do, the nuts might come loose. Your wheel could fall off, causing a serious accident. 10.
Page 225
12. Tighten the wheel nuts firmly in a criss-cross sequence as shown. Turn the ratchet clockwise with the UP mark facing you. CAUTION: 11. Lower the vehicle by turning the ratchet Incorrect wheel nuts or improperly tightened counterclockwise. Lower the jack completely. wheel nuts can cause the wheel to become loose and even come off.
Page 226
NOTICE: Improperly tightened wheel nuts can lead to brake pulsation and rotor damage. avoid expensive brake repairs, evenly tighten the wheel Storing a jack, a tire or other equipment in the nuts in the proper sequence and to the proper passenger compartment of the vehicle could torque specification.
Page 227
Put the flat tire the ground at the rear of the vehicle, with the valve stem pointed down. Tilt retaining bar downward and through the wheel opening. Make sure it is fully seated across the underside of the wheel. Attach the ratchet, with the UP side facing you, to the extension.
Compact Spare Tire NOTICE: Although the compact spare tire was fully inflated when your vehicle was new, it can lose air after a time. Check When the compact spare is installed, don’t take the inflation pressure regularly. It should be 60 psi your vehicle through an automatic car wash with (420 Wa).
If You’re Stuck: In Sand, Mud, Ice NOTICE: or Snow What you don’t want to do when your vehicle is stuck is Spinning your wheels can destroy parts of your to spin your wheels too fast. The method known as vehicle as well as the tires.
Section 6 Service and Appearance Care Here you will find information about the care of your vehicle. We hope you’ll want to keep your GM vehicle all GM. This section begins with service and fuel information, and Genuine GM parts have one of these marks: then it shows how to check important fluid and lubricant levels.
Doing Your Own Service Work CAUTION: If you want to do some of your own service work, you’ll want to get the proper GM Service Manual. It tells you much more about how to service your vehicle than this You can be injured and your vehicle could be manual can.
Page 233
If your vehicle is certified’ to meet California Emission Fuel Standards (indicated on the underhood tune-up label), Use regular unleaded ‘gasoline rated at 87 octane or it is designed to operate on fuels that meet California higher. At a minimum, it should meet specifications specifications.
Fuels in Foreign Countries To provide cleaner air, all gasolines are now required to Contain additives that will help prevent deposits from If you plan on driving in another country outside the forming in your engine and fuel system, allowing your United States or Canada, the proper fuel may be hard emission control system to function properly.
Page 235
CAUTION: Gasoline vapor is highly flammable. It burns violently, and that can cause very bad injuries. Don’t smoke if you’re near gasoline or refueling your vehicle. Keep sparks, flames and smoking materials away from gasoline. The cap is behind a hinged door on the driver’s side of your vehicle.
Page 236
- - - CAUTION: If you get gasoline on yourself and then. something ignites it, you could be badly burned. Gasoline can spray ,out on you if you open the fuel filler cap too quickly. This spray can happen if your tank is nearly full, and is more likely in hot weather.
Checking Things Under the Hood When you put the cap back on, turn it to the right until you hear at least three clicks. Make sure you fully install the cap. The diagnostic system can determine if the fuel cap has been left off or improperly installed. This would CAUTION: allow fuel to evaporate into the atmosphere.
Hood Release Then go to the front of the vehicle and release the secondary hood release. To open the hood, first pull the handle inside the vehicle on the lower driver’s side of the kick panel.
Page 239
When you open the hood, this is what you will see: A. Windshield Washer Fluid Fill Location F. Oil Fill Location B. Coolant Fill Location G. Brake Master Cylinder Reservoir C. Oil Dipstick Location H. Power Steering Fluid Reservoir D. Transmission Dipstick/Fill Location I.
Page 240
Remove the hood prop from the slot in the hood and return the prop its retainer. Then just pull the hood down and close it firmly. Lift the hood, release the hood prop from its retainer and put the hood prop into the slot in the hood. Before closing the hood, be sure all the filler caps are on properly.
Engine Oil If the CHECK OIL light on the instrument panel comes on, it means you need to check your engine oil level CHECK right away. For more information, see “Check Oil Light” in the Index. You should check your engine oil level regularly; this is an added reminder.
When to Add Oil Checking Engine Oil If the oil is at or below the ADD line, then you’ll need Pull out the dipstick and clean it with a paper towel or to add some oil. But you must use the right kind. This cloth, then push it back in all the way.
What Kind of Oil to Use RECOMMENDED SAE VISCOSITY GRADE ENGINE OILS Oils recommended for your vehicle can be identified by FOR BEST FUEL ECONOMY AND COLD STARTING, SELECT LOWEST looking for the “Starburst” symbol. This symbol SAE VISCOSITY GRADE OIL FOR THE EXPECTED TEMPERATURE RANGE. indicates that the oil has been certified by the American Petroleum Institute (API).
shown in the chart, 5W-30 is best for your When to Change Engine Oil vehicle. However, you can use 1OW-30 if it’s going See if any one of these is true for you: to be 0°F 18 “C) or above. These numbers on an oil thickness.
Engine Cover What to Do with Used Oil Did you know that used engine oil contains certain Removing the Engine Cover elements that may be unhealthy for your skin and could 1. Move both front seats as far back as they will go. even cause cancer? Don’t let used oil stay on your skin for very long.
Page 246
The nuts are located at the bottom of the extension Unscrew the screws located near the top on each side on the driver and passenger side corners. the extension. Grasp the extension from both sides and gently remove 6-16...
Page 247
6. Grasp the top of the heater duct and pull downdgently 5. Disconnect the electrical connectors set the to remove. extension aside. 6-17...
Page 248
7. Remove the two bolts at the engine cover. The bolts 8. Grasp the bottom of the cover and slide it rearward. are not supposed to come out of the cover, only from Then, lift it up and out of the vehicle. the front of the dash.
Air Cleaner Installing the Engine Cover 1. Lift the engine cover into the vehicle and slide it all the way forward. Make sure the rubber seal is over the latches. 2. Install the two bolts at the engine cover. 3. Put the heater duct over the engine cover studs. Push up on the duct gently until it snaps into place.
Refer to the Maintenance Schedule to determine when to Automatic Transmission Fluid replace the air filter and the crankcase ventilation filter. When to Check and Change See “Scheduled N ntenance Services” in the Index. A good time to check your automatic transmission fluid level is when the engine oil is changed, Change both the fluid and filter every 15,000 miles (25 000 km) if the vehicle is mainly driven under one...
Wait at least 30 minutes before checking the How to Check transmission fluid level if you have been driving: Because this operation can be a little difficult, you When outside temperatures are above 90°F (32°C). may choose to have this done at your GM dealer Service Department.
Page 252
Checking Transmission Fluid Cold Then, without shutting off the engine, follow these steps: A cold check is made after the vehicle has been sitting more with the engine off and is used for eight hours only as a reference. Let the engine run at idle for five minutes if outside temperatures are 50°F (10°C) or more.
fluid to bring the level up to the HOT area for check. It doesn’t take much fluid, generally less than a pint (0.5 L). Don ove$iZl. We recommend you use only ’r fluid labeled DEXRON@-111, because fluid with that label is made especially for your automatic transmission. Damage caused by fluid other than DEXRON-TI1 is not covered by your new vehicle warranty.
How to Check Lubricant Front Axle When to Check and Change Lubricant Refer to the Maintenance Schedule to determine how often to check the lubricant and when to change it. See “Scheduled Maintenance Services” in the Index. How to Check Lubricant If the level is below the bottom of the filler plug hole, you’ll need to add...
Rear Axle What to Use Refer to the Maintenance Schedule to determine what When to Check and Change Lubricant kind of lubricant to use. See “Recommended Fluids and Refer to the Maintenance Schedule to determine how Lubricants” in the Index. often to check the lubricant and when to change it.
Page 256
GM Engine Coolant Supplement (sealer) (GM Part NOTICE: No. 3634621) with any complete coolant change. If you use this mixture, you don’t need to add anything else. When adding coolant it is important that you use DEX-COOL (orange-colored, silicate-free) CAUTION: coolant meeting GM Specification 6277M.
Checking Coolant NOTICE: If you use an improper coolant mix, your engine could overheat and be badly damaged. The repair cost wouldn’t be covered by your warranty. Too much water in the mix can freeze and crackthe engine, radiator, heater core and other parts. If you have to add coolant more than four times a year, have your dealer check your cooling system.
Page 258
Add coolant mix at the recovery tank, but be,careful not Adding Coolant to spill it. If ,you need more coolant, add the proper mix at the CAUTION: You can be burned if you spill coolant on hot engine parts. Coolant contains ethylene glycol, Turnj the radiator pressure cap when the will burn if the engine parts are hot...
Radiator Pressure Cap NOTICE: Your radiator cap is a 15 psi (105 kPa) pressure-type cap and must be tightly installed to prevent coolant loss and possible engine damage from overheating. Be sure the arrows on the cap line up with the overflow tube on the radiator filler neck.
When to Check Power Steering Fluid Thermostat to reg,ularlY check Power steering It is not necessary Engine coolant temperature is controlled by thermostat fluid unless you suspect there is leak in the system or in the engine coolant system. The thermostat stops the you hear an unusual noise.
Windshield Washer Fluid NOTICE: What to Use When using concentrated washer fluid, When you need windshield washer fluid, be sure to read follow the manufacturer’s instructions for the manufacturer’s instructions before use. If you will be operating your vehicle in an area where the temperature adding water.
leaking out of the brake system. If it is, you should have Brakes your brake system fixed, since a leak means that sooner Brake Fluid or later your brakes won’t work well, or won’t work at all. So, it isn’t a good idea to “top off’ your brake fluid. Adding brake fluid won’t correct a leak.
Page 263
What to Add Checking Brake Fluid When you do need brake fluid, use only DOT-3 brake fluid -- such Delco Supreme 11 (GM Part No. 1052535). Use new brake fluid from sealed container only, and always clean the brake fluid reservoir ca.
CAUTION: Using the wrong fluid can badly damage The brake wear warning sound means that brake system parts. For example, just sooner or later your brakes won’t work well. drops of mineral-based oil, such as engine That could lead to an accident. When you hear oil, in your brake system can damage brake the brake wear warning sound, have your system parts so badly that they’ll have to be...
Replacing Brake System Parts Your rear drum brakes don’t have wear indicators, but if you ever hear a rear brake rubbing noise, have the The braking system on a modern vehicle is complex. rear brake linings inspected. Also, the rear brake drums Its many parts have to be of top quality and work well should be removed and inspected each time the tires are together if the vehicle is to have really good braking.
Bulb Replacement Vehicle Storage If you’re not going to drive your vehicle for 25 days or more, Before replacing any bulbs, make sure all lamps are off take off the black, negative cable from the battery. This and the vehicle is not running. See “Replacement Bulbs” will help keep your battery from running down.
Page 267
3. Install the new bulb into the connector. Headlamps 4. Reverse Steps 1 and 2 to reinstall the headlamp. Sealed Beam Lamps Composite Headlamps 1. Remove the four retainer screws and the retainer. 1. Open the hood. 2. Remove the two screws from the sidemarkedturn signal lamp.
Page 268
4. Remove the screw located behind the corner reflector in order to remove the entire corner reflector. 3. Completely remove the sidemarkedturn signal lamp by pulling out the assembly and disconnecting the sidemarkedturn signal lamp sockets from the lamp. 6-38...
Page 269
6. Remove the composite assembly. 7. Turn the halogen bulb counterclockwise to remove from the assembly. 5. Remove the remaining three screws; the first one 8. Install the new bulb into the composite assembly by from the corner reflector pocket and the two turning it clockwise until it is completely-tightened.
Taillamps Front Turn Signal -Lamps rear 1. Remove the two screws at the inside edge of the 1. Open the door. parking/turn signal lamp assembly. 2. Remove the two screws from behind the door. 2. Remove the lamp assembly. 3. Squeeze the tab on the side of the lamp socket while turning the socket counterclockwise.
Page 271
4. Press the tab and turn the socket counterclockwise to remove the socket from the bezel. If the socket does not have tab, turn the socket counterclockwise to remove the socket from the bezel. 5 . Reverse Steps 1 through to reinstall the taillamp.
Windshield Wiper Blade Replacement CAUTION: To replace your windshield wiper blade ‘inserts, lift Poorly maintained and improperly used tires the wiper arm away‘from are dangerous. the windshield. Overloading your tires can cause overheating as a result of too much friction.’ You could have an air-out and a serious accident.
Page 273
Inflation Tire Pressure NOTICE: (Continued) The Certificatioflire label, which is on the rear edge of the driver’s door, shows the correct inflation pressures your tires have too much air (overinflation). for your tires when they’re cold. “Cold” means your you can get the following: vehicle has been sitting for at least three hours or driven Unusual wear no more than 1 mile (1.6 km).
Tire Inspection and Rotation When rotating your tires, always use the correct rotation pattern shown here. Tires should be inspected every 6,000 to 8,000 miles Don’t include the compact spare tire in your tire rotation. (10 000 to 13 000 k m ) for any signs of unusual wear.
The tire has a bump, bulge or split. When It’s Time for New Tires The tire has a puncture, cut or other damage. that, One way to tell when it’s can’t be repaired well because of the size or location time for new tires is to of the damage.
not apply to deep tread, winter-type snow tires, space-saver or temporary use spare tires, tires with nominal rim diameters of 10 to 12 inches (25 to 30 cm), or to some limited-production tires. ng tires could cause you to lose control while While the tires available on General Motors passenger driving.
Traction A, B, C excessive loading, either separately or in combination. can cause heat buildup and possible tire failure. The traction grades, from highest to lowest, are A, and C, and they represent the tire’s ability to stop on wet Wheel Alignment and Tire Balance pavement as measured under controlled conditions on The wheels on your vehicle were aligned and balanced...
Page 278
you need to replace any of your wheels, wheel bolts NOTICE: or wheel nuts, replace them only with new GM original parts. equipment This way, you will be sure to have the right wheel, wheel bolts and wheel nuts for your The wrong wheel can also cause problems with vehicle model.
rire Chains Appearance Care Remember, cleaning products can be hazardous. Some NOTICE: are toxic. Others can burst into flame if you strike a match or get them a hot part of the vehicle. Some are dangerous if you breathe their fumes in a closed space. If your vehicle has P235/65R15 size tires, don’t...
use any of these unless this manual says you can. Use solvent-type cleaners in a well-ventilated area Don’t only. If you use them, don’t saturate the stained area. In many uses, these will damage your vehicle: If a ring forms after spot cleaning, clean the entire Alcohol area immediately or will set.
Page 281
Using Solvent-Type Cleaner on Fabric Special Cleaning Problems First, see if you have to solvent-type cleaner at all. Greasy or Oily Stains Some spots and stains will clean off better with just Stains caused by grease, oil, butter, margarine, shoe water and mild soap.
Non-Greasy Stains Cleaning Vinyl coffee Stains caused catsup, (black), egg, fruit, fruit Use warm water and a clean cloth. juice, milk, soft drinks, wine, vomit, urine and blood can Rub with a clean, damp cloth to remove dirt. You be removed as follows: may have to do it more than once.
Cleaning the Top of the Instrument Panel Don’t use abrasive cleaners glass, because they may cause scratches. Avoid placing decals on the inside rear Use only mild soap and water to clean the top surfaces window, since they may have to be scraped off later. If of the instrument panel..
soft, clean chamois or a 100% cotton towel to avoid Weatherstrips surface scratches and water spotting. Silicone grease weatherstrips will make them last cause High pressure vehicle washes may water to enter longer, seal better, and not stick or squeak. Apply silicone your vehicle.
Foreign materials such as calcium chloride and other Aluminum Wheels (If So Equipped) salts, ice melting agents, road oil and tar, tree sap, bird Keep your wheels clean using a soft clean cloth with droppings, chemicals from industrial chimneys, etc., can mild soap and water.
Finish Damage Tires clean your tires, use a stiff brush with a tire cleaner. stone chips, fractures or deep scratches in the finish should be repaired right away. Bare metal will corrode quickly and may develop into a major repair expense. NOTICE: Minor chips and scratches can be repaired with touch-up materials available from your dealer or other service...
Chemical Paint Spotting Fiberglass Springs Some weather and atmospherkconditions can create a chemical fallout. Airborne pollutants can fall upon ,NOTICE: and attack painted surfaces on your vehicle. This damage can take two forms: blotchy, ringlet-shaped Don’t use corrosive or acidic cleaning agents, discolorations, and small irregular dark spots etched engine degreasers, aluminum cleaning agents or into the paint surface.
Appearance Care Materials Chart PART NUMBER SIZE DESCRIPTION USAGE Chamois Shines vehicle without scratching 1050004 2.75 sq. 1050172 oz. (0.473 L) Tar and Road Oil Remover 16 Also removes old waxes and polishes oz. (0.473 L) Removes rust and corrosion 1050173 Chrome Cleaner and Polish 16 16 oz.
Service Parts Identification Label Vehicle Identification Number (VIN) You’ll find this label on the inside of the front storage compartment door. It’s very helpful if you ever need to order parts. On this label is: your VIN, t ‘ the model designation, ENGINE/l996 ASSEMBLY CODE...
Headlamp Wiring Electrical System The headlamp wiring is protected by a circuit breaker in Add-on Electrical Equipment the lamp switch. An electrical overload will cause the lamps to go on and off, or in some cases to remain off. If this happens, have your headlamp wiring checked NOTICE: right away.
Instrument Panel Fuse Block Fuses and Circuit Breakers The wiring circuits in your vehicle are protected from short circuits by a combination of fuses, circuit breakers and fusible thermal links. This greatly reduces the chance of fires caused by electrical problems. Look at the silver-colored band inside the fuse.
Page 292
FuseKircuit Usage Breaker DRL Relay, DRL Module, Chime Headlamp Switch, Keyless Entry, c57 c 7 Cluster, Overhead Console Not Used Cruise Module, Cruise Activator Switch Power Outlets, ALDL, Subwoofer Amplifier c 7 c87 c 7 c 3 Not Used License Plate Lamp, Taillamps, c 7 c 7 c 7 Parking Lamps, Ashtray Lamp, Panel Lights, Trailer Taillamps, Front and...
Page 293
Fuse/Circuit Usage Fuse/Circuit Usage Breaker Breaker Cluster HVAC Controls, Chime PRNDLI Odometer, TCC Enable and Module, Radio Illumination, Rear Heat PWM Solenoids, Shift A and Shift B Switch Illumination, Rear Solenoids, 3-2 Downshift Solenoids WiperNasher Switch Illumination, Not Used Rear Liftgate Switch Illumination, Not Used Remote Cassette Illumination, Rear Wiper, Rear Washer Pump...
Page 294
Underhood Electrical Center I - ) ( - ) ( - 1 [ - ) IIVC) ( - ) Feed Usage The underhood electrical center is located toward the ..Upfitter Battery Feed AUXB rear of the engine compartment on the driver's side. .
Air Conditioning Refrigerant Capacity Air Conditioning Refrigerants Not all air conditioning refrigerants are the same. System Quantity* If the air conditioning system in your vehicle needs 2.00 Ibs. (0.91 refrigerant, be sure the proper refrigerant is used. R- 134a C-60** If you’re not sure, ask your GM dealer.
Normal Maintenance . . . Fuel Filter GF481 Replacement Parts ....Radiator Cap RC27 Replacement part numbers listed in this section are 22110158, Pin Type Wiper Blades (Front) based on the latest information available at the time of...
Introduction IMPORTANT. Your Vehicle and the Environment KEEP ENGINE OIL AT THE PROPER Proper vehicle maintenance not only helps to keep your LEVEL AND CHANGE AS vehicle in good working condition, but also helps the RECOMMENDED environment. All recommended mainteqance procedures are important.
“Part B: Owner Checks and Services” tells you How This Section is Organized what should be checked whenever you stop for fuel. It The remainder of this section is divided into five parts: also explains what you can easily do to help keep your vehicle in good condition.
Part A: Scheduled Maintenance The proper fluids and lubricants to use are listed in P a r t D. Make sure whoever services your vehicle Services uses these. All parts should be replaced and all necessary repairs done before you or anyone else Using Your Maintenance Schedule drives the vehicle.
Maintenance Schedule Short TripKity Definition Short Trip/City Intervals Every 3,000 Miles 000 km): Engine Oil and Filter Follow the Short TripKity Maintenance Schedule if any Change (or 3 months, whichever occurs first). Chassis one of these conditions is true for your vehicle: Lubrication (or 3 months, whichever occurs first).
Maintenance Schedule Tripmighway Long Definition Long Trip/Highway Intervals Every 7,500 Miles (12 500 km): Engine Oil and Filter Follow this maintenance schedule only if none of the Char,ge (or every 12 months, whichever occurs first). conditions from the Short Trip/City Maintenance Chassis Lubrication (or every 12 months, whichever Schedule is true.
Short Trip/City Maintenance Schedule The services shown in this schedule up to 100,000 miles Drive a lxle service: (166 000 km) should be performed after 100,000 miles Locking Differential -- Drain fluid and refill at first (166 000 km) at the same intervals. engine oil change.
Page 307
Short TripKity Maintenance Schedule 3,000 Miles (5 000 km) 6,000 Miles (10 000 km) Change engine oil and filter (or every Change engine oil and filter (or every 3 months, whichever occurs first). 3 months, whichever occurs first). An Emission Control Service. An Emission Control Service.
Page 308
Short TripKity Maintenance Schedule 12,000 Miles (20 000 km) 9,000 Miles (15 000 km) Change engine oil and filter (or every Change engine oil and filter (or every 3 months, whichever occurs first). 3 months, whichever occurs first). An Emission Control Service. An Emission Control Service.
Page 309
Short Trip/City Maintenance Schedule 15,000 Miles (25 000 km) Change engine oil and filter (or every Change automatic transmission f l r lid and filter if the vehicle is mainly driven under 3 months, whichever occurs first). one or more of these conditions: An Emission Control Service.
Page 310
Short Trip/City Maintenance Schedule 18,000 Miles (30 000 km) 21,000 Miles (35 000 km) Change engine oil and filter (or every Change engine oil and filter (or every 3 months, whchever occurs first). 3 months, whichever occurs first). An Emission Control Service. An Emission Control Service.
Short TripKity Maintenance Schedule 24,000 Miles (40 000 km) 27,000 Miles (45 000 km) Change engine oil and filter (or every Change engine oil and filter (or evi 3 months, whichever occurs first). 3 months, whichever occurs first). An Emission Control Service. An Emission Control Service.
Page 312
Short TripKity Maintenance Schedule 30,000 Miles (50 000 km) Replace fuel filter. Change engine oil and filter (or every 3 months, whichever occurs first). An Emission Control Service. An Emission Control Service. Replace air cleaner filter. Lubricate chassis components; see An Emission Control Service.
Page 313
Short TripKity Maintenance Schedurl 33,000 Miles (55 000 km) When doing frequent trailer towing. Change engine oil and filter (or every 3 months, whichever occurs first). Uses such as found in taxi, police or An Emission Control Service. delivery service. Lubricate chassis components;...
Page 314
Short Trip/City Maintenance Schedule. 36,000 Miles (60 000 km) 39,000 Miles, 000 kim)~ Change engine oil and filter (or every Change engine oil and filter (or every 3 months, whichever occurs first). 3 months, whichever occurs first). An Emission Control Service. An Emission Control Service.
Page 315
Short Trip/City Maintenance Schedule 45,000 Miles (75 000 km) 42,000 Miles (70 000 km) Change engine oil and filter (or every Change engine oil and filter (or’every 3 months, whichever occurs first). months, whichever occurs first). An Emission Control Service. An Emission Control Service.
Page 316
Short Trip/City Maintenance Schedule 45,000 Miles (75 000 km) (Continued) , # - . Inspect air cleaner filter if you are driving Change automatic transmission fluid and in .dusty conditions. Replace filter if filter if the vehicle is mainly driven under necessary.
Page 317
Short n$City Maintenance Schedule 48,000 Miles (80 000 km) 51,000 Miles (85 000 km) Change engine oil and filter (or every Change engine oil and filter (or every 3 months, whichever occurs first). 3 months, whichever occurs first). An Emission Control Service. Emission Control Service.
Page 318
Short ‘Trip/City Maintenance Schedule 54,000 Miles (90 000 km) 57,000 Miles. (95 000 km) Change engine oil and filter (or every Change engine oil, and filter (or every 3 months, whichever occurs first). 3 months, whichever occurs first). An Emission Control Service: An Emission Control Service.
Page 319
Short TripJCity Maintenance Schedule 60,000 Miles (100 000 km) Change engine oil and filter (or every Change a1 ltomatic transmission fl .uid and 3 months, whichever occurs first). filter if the vehicle is mainly driven under one or more of these conditions: An Emission Control Service.
Page 320
Short ,Trip/City -Maintenance. Schedule 63,000 Miles (105 000, km) 60,000 Miles (100‘ 000 (Continued) Change engine,oil and filter (or every Inspect engine accessory drive belt. 3 months, whichever occurs first). Replace fuel filter. An Emission Control Service. An Emission Control Service. Lubricate ‘chassis components;...
Page 321
Short TripKity Maintenance Schedule 66,000 Miles (110 000 km) 69,000 Miles (115 000 km) Change engine oil and filter (or every Change engine oil and filter (or every 3 months, whichever occurs first). 3 months, whichever occurs first). An Emission Control Service. An Emission Control Service.
Page 322
Short TripKity Maintenance Schedule 72,000 Miles (120 000 km) 75,000 Miles (125 000 km) Change engine oil and filter (or every Change engine oil and filter (or every 3 months, whichever occurs first). months, whichever occurs first). An Emission Control Service. An Emission Control Service.
Page 323
Short TripKity Maintenance Schedule 78,000 Miles (130 000 km) Change engine oil and filter (or every When doing frequent trailer towing. 3 months, whichever occurs first). Uses such as found in taxi, police or An Emission Control Service. delivery service. Lubricate chassis components;...
Page 324
Short TripKity Maintenance Schedule 81,000 Miles (135 000 km) 84,000 Miles (140 000 km) Change engine oil and filter (or every Change engine oil and filter (or every 3 months, whichever occurs first). 3 months, whichever occurs first). An Emission Control Service. An Emission Control Service.
Page 325
Short. TripKity Maintenance Schedule 90,000 Miles (150 000 km) 87,000 Miles (145 000 km) Change engine oil and filter (or every Change engine oil and filter (or every 3 months, whichever occurs first). 3 months, whichever occurs first). An Emission Control Sewice. An Emission Control Service.
Page 326
Short Trip/City Maintenance Schedule 90,000 Miles 000 km) (Continued) (150 Change automatic transmission fluid and Replace fuel filter. filter if the vehicle is mainly driven under An Emission Control Service. one or more of these conditions: Replace air cleaner filter. heavy city traffic where the outside An Emission Control Service.
Page 327
Short Trip/City Maintenance Schedule 93,000 Miles (155 000 km) 96,000 Miles (160 000 km) Change engine oil and filter (or every Change engine oil and filter (or every 3 months, whichever occurs first). 3 months, whichever occurs first). An Emission Control Service. An Emission Control Service.
Page 328
Short TripKity Maintenance Schedule 100,000 Miles (1 66 000 km) 99,000 Miles (165 000 km) Drain, flush and refill cooling system Change engine oil and filter (or every (or every months since last service, 3 months, whichever occurs first). whichever occurs first). See “Engine An Emission Control Service.
Long Tripmighway Maintenance Schedule The services sbown in this schedule up to 100,000 miles Drive axle service: (166 000 km) should be performed after 100,000 miles Locking Differential Drain fluid and refill at first (166 000 km) at the same, intervals. engine oil change.
Page 330
7,500 Miles (12 500 km) 15,000 Miles (25 000 km) Change engine oil filter (or every Change engine oil and filter (or every 12 months, whichever occurs first). 12 months, whichever occurs first). An Emission Control Service. An Emission Control Service. Lubricate chassis components;...
Page 331
Long Trip/Higl 22,500 Miles (37 500 km) hilly or mountainous terrain. Change engine oil and filter (or every 12 months, whichever occurs first). - When doing frequent trailer towing. An Emission Control Service. Uses such as found in taxi, police or Lubricate chassis components;...
Page 332
Long Tripmighway Maintenance Schedule 30,000 Miles (50 000 km) Change engine oil and filter (or every In hilly or mountainous terrain. 12 months, whichever occurs first). When doing frequent trailer towing. An Emission Control Service. Uses such as found in taxi, police or Lubricate chassis components;...
Page 333
37,500 Miles (62 500 km) 45,000 Miles (75 000 km) Change engine oil and filter (or e Change engine oil and filter (or every ,veri 12 months, whichever occurs first). months, whichever occurs first). An Emission Control Service. An Emission Control Service. Lubricate chassis components;...
Page 334
Schedule TriplHighway Maintenance 52,500 Miles (87 500 km) 45,000 Miles 000 km) (Continued) In hilly or mountainous terrain. Change engine oil and filter (or every 12 months, whichever occurs first). - When doing frequent trailer towing. An Emission Control Service. Uses such as found in taxi, police or Lubricate chassis components;...
Long Trip/Highway Maintenance Schedule 60,000 Miles (100 000 km) Ch ange automatic transmission fluid and Change engine oil and filter (or every 12 months, whichever occurs first). filter if the vehicle is mainly driven under one or more of these conditions: An Emission Control Service.
Page 336
67,500 Miles (112 500 km) 60,000 Miles (1 00 000 km) (Continued) Change engine oil and filter (or every Inspect engine accessory drive belt. 12 months, whichever occurs first). Replace fuel filter. An Emission Control Service. An Emission Control Service.? Lubricate chassis components;...
Page 337
Long Tripmighway Maintenance Schedule 75,000 Miles (125 000 km) Change engine oil and filter (or every In hilly or mountainous terrain. months, whichever occurs first). When doing frequent trailer towing, An Emission Control Service. Uses such as found in taxi, police or Lubricate chassis components;...
Page 338
Long Trip/Highway Maintenance Schedule 90,000 Miles (150 000 km) 82,500 Miles (137 500 km) Change engine oil and filter (or every Change engine oil and filter (or every 12 months, whichever occurs first). 12 months, whichever occurs first). An Emission Control Service. An Emission Control Service.
Page 339
Long Trip/Highway Maintenance Schedule 97,500 Miles (162 500 km) In hilly or mountainous terrain. Change engine oil and filter (or every 12 months, whichever occurs first). When doing frequent trailer towing. An Emission Control Service. Uses such as found in taxi, police or Lubricate chassis components;...
Page 340
Long Trip/Highway M 100,000 Miles (166 000 km) Drain, flush and refill cooling system Replace spark plugs. (or every 60 months since last service, An Emission Control Service. whichever occurs first). See “Engine Inspect Positive Crankcase Ventilation Coolant” in the Index for what to use. (PCV) valve.
Engine Coolant Level Check Part B: Owner Checks and Services Check the engine coolant level and add the proper Listed below are owner checks and services which coolant mix if necessary. See “Engine Coolant” in the should be performed at the intervals specified to help Index for further details.
At Least Twice a Year At Least Once a Year Restraint System Check Key Lock Cylinders Service Make sure the safety belt reminder light and all your Lubricate the key lock cylinders with the lubricant belts, buckles, latch plates, retractors and anchorages are specified in Part D.
Page 343
Brake-Transmission Shift Interlock (BTSI) Check Starter Switch Check CAUTION: When you are doing this check, the vehicle could When you are doing this check, the vehicle could move suddenly. If it does, you or others could be move suddenly. If it does, you or others could be injured.
Page 344
Park on a fairly steep hill, with the vehicle facing Steering Column Lock Check downhill. Keeping your foot on the regular brake, set the While parked, and with the parking brake set, try to turn parking brake. the key to LOCK in each shift lever position. To check the parking brake: With the engine running The key should turn to LOCK only when the shift and transmission in NEUTRAL (N), slowly remove...
Page 345
Exhaust System Inspection Part C: Periodic Maintenance Inspections Inspect the complete exhaust system. Inspect the body near the exhaust system. Look for broken, damaged, Listed below are inspections and services which should missing or out-of-position parts as well as open seams, be performed at least twice a year (for instance, each holes, loose connections other conditions which could...
Drive Axle Service Brake System Inspection Inspect the complete system. Inspect brake lines and Check readfront axle fluid level and add as needed. Check constant velocity joints and axle seals for leaking. hoses for proper hook-up, binding, leaks, cracks, chafing, etc. Inspect disc brake pads for wear and rotors Transfer Case (All-Wheel Drive) Inspection for surface condition.
Page 347
Part D: Recommended Fluids and USAGE FLUIDLUBRICANT Lubricants GM Part No. 3634621 or Coolant equivalent with a complete flush NOTE: Fluids and lubricants identified below by name, Supplement part number or specification may be obtained from your Sealer and refill. GM dealer.
Page 348
USAGE FLUIDLUBRICANT USAGE FLUIDLUBRICANT Chassis Chassis lubricant (GM Part Hood Latch Lubriplate lubricant aerosol (GM Lubrication No. 1052497 or equivalent) or Assembly Pivots, Part No. 12346293 or equivalent) ’ lubricant meeting requirements of Spring Anchor or lubricant meeting requirements NLGI Grade 2, Category LB or and Release of NLGI Grade 2, Category LB GC-LB.
Page 349
Part E: Maintenance Record aervices” or “Periodic Maintenance” can be added on After the scheduled services are performed, record the the following record pages. Also, you should retain all date, odometer reading and who performed the service in the boxes provided after the maintenance interval. maintenance receipts.
Page 350
Maintenance Record SERVICED BY MAINTENANCE PERFORMED...
Section 8 Customer Assistance Information Customer Satisfaction Procedure Here you will find out how to contact Chevrolet if you need assistance. This section also tells you how to obtain service publications and how to report any safety defects. This section includes information on:...
Page 352
Your satisfaction and goodwill are important to your For help outside of the United States and Canada, call dealer and Chevrolet. Normally, any concern you may the following numbers as appropriate: have with your vehicle can be handled by your selling or In Mexico: (525) 625-3256 servicing dealer.
To assist customers who are deaf, hard of hearing, or speech-impaired and who use Text Telephones (TTYs), Nature of concern Chevrolet has TTY equipment available at its Customer We encourage you to call us so we can give your inquiry Assistance Center. Any TTY user can communicate with prompt attention.
Chevrolet is excited to announce the Care Plus: establishment of the Chevrolet/Geo Roadside Assistance Center. As the owner of a 1996 Chevrolet/Geo, FREE Non-Warranty Towing (to the closest dealer membership in Roadside Assistance is free. from a legal roadway)
Page 355
Vehicle Identification Number (VIN) the coverage provided by the Bumper to Bumper License plate number New Vehicle Limited Warranty to eligible purchasers of 1996 Chevrolet/Geo passenger car and light duty Vehicle color trucks. (Please see your selling dealer for details.) Vehicle location...
21 years of age. If you are Up to $30 maximum daily vehicle rental allowance for under 21 and have difficulty renting a vehicle, Chevrolet any overnight warranty repair up to five days, OR will reimburse...
Page 357
BBB AUTO LINE Council of Better Business Bureaus Both Chevrolet and your Chevrolet dealer are committed 4200 Wilson Boulevard to making sure you are completely satisfied with your new Suite 800 vehicle.
Safety Administration (NHTSA), in addition to to resolve the complaint serving as an intermediary notifying General Motors. between you and Chevrolet. If this mediation is If NHTSA receives similar complaints, it may open an unsuccessful, an informal hearing will be scheduled...
Service manuals, service bulletins, owner’s manuals and Chevrolet Motor Division other service literature are available for purchase for all Chevrolet Customer Assistance Center current and many past model General Motors vehicles. P.O. Box 7047 Toll-free telephone numbers for ordering information: Troy, Michigan 48007-7047 .
Service Manuals number of vehicles. Some will describe inexpensive service; others will describe expensive service. Some Service ,manuals contain diagnostic and repair will advise of new or unexpected conditions, and others information for all chassis and body systems. They may help avoid future costly repairs. Service bulletins may be useful for owners who wish to get a greater are meant for qualified technicians.