ENGLISH
n Using the macro function
1
3UHVV
MACRO
2
3UHVV WKH
EXWWRQ
QUICK SELECT
\RX XVHG WR VWRUH WKH PDFUR
IXQFWLRQ
Button
Macro number
QUICK SELECT 1
MACRO-1
QUICK SELECT 2
MACRO-2
QUICK SELECT 3
MACRO-3
n Resetting the macro function
1
3UHVV DQG KROG
POWER ON
IRU DW OHDVW
ZONE/DEVICE ON
VHFRQGV
"SETUP" flashes twice on the remote
control unit.
2
8VH ui WR GLVSOD\ ³5(6(7´ RQ
WKH UHPRWH FRQWURO XQLW DQG SUHVV
ENTER
3
8VH ui WR GLVSOD\ ³0$&52´
RQ WKH UHPRWH FRQWURO XQLW DQG
SUHVV
ENTER
4
:KHQ ³0&1R" ´ DSSHDUV RQ WKH
UHPRWH FRQWURO XQLW SUHVV WKH
EXWWRQ WKDW \RX
QUICK SELECT
ZDQW WR UHVHW
"RESET" flashes four times on the
remote control unit and the normal
operation mode is restored.
Button
QUICK SELECT 1
QUICK SELECT 2
QUICK SELECT 3
114
Specifying the zone used with the main
remote control unit
ZONE SELECT
When the
operated with the remote control unit.
• The factory setting is "M234".
1
3UHVV DQG KROG
ZONE/DEVICE ON
VHFRQGV
"SETUP" flashes twice on the remote
control unit.
2
8VH ui WR GLVSOD\ ³=21(/´ RQ
WKH UHPRWH FRQWURO XQLW DQG SUHVV
ENTER
DQG
3
8VH ui WR VHW WKH ]RQH WR EH XVHG
DQG SUHVV
"SET" flashes four times on the remote
control unit and the normal operation
mode is restored.
Remote control unit
display
M
M2
M23
M234
Macro number
MACRO-1
MACRO-2
MACRO-3
button is pressed, only the set zone can be
DQG
POWER ON
IRU DW OHDVW
ENTER
Zone to be used
MAIN ZONE only
MAIN ZONE /
ZONE2
MAIN ZONE /
ZONE2 /
ZONE3
MAIN ZONE /
ZONE2 /
ZONE3 /
ZONE4
Operating the main remote control unit
Setting the Remote ID
When using multiple DENON AV receivers in the same room, make
this setting so that only the desired AV receiver operates.
• The factory setting is "ID-1".
1
3UHVV DQG KROG
DQG
POWER ON
IRU DW OHDVW
ZONE/DEVICE ON
VHFRQGV
"SETUP" flashes twice on the remote
control unit.
2
8VH ui WR GLVSOD\ ³5&,'´ RQ
WKH UHPRWH FRQWURO XQLW DQG SUHVV
ENTER
3
8VH ui WR VHW WKH UHPRWH ,' DQG
SUHVV
ENTER
"SET" flashes four times on the remote
control unit and the normal operation
mode is restored.
Remote control unit
Remote ID
display
ID-1
1
ID-2
2
ID-3
3
ID-4
4
NOTE
When you change the remote ID, make sure that the remote
control unit and the remote ID of the main unit are exactly the same
(vpage 105).