Denon AVR-A100 Owner's Manual page 115

ENGLISH
Operating learning function
If the AV device is not a DENON device, or if the device does not
operate even when the preset code is registered, use the learning
function. Remote codes for different devices can be remembered for
use by the DENON remote control included with this device.
n Remembering remote control codes from other
devices
1
3UHVV DQG KROG
POWER ON
IRU DW OHDVW 
ZONE/DEVICE ON
VHFRQGV
"SETUP" flashes twice on the remote
control unit.
2
8VH ui WR GLVSOD\ ³/($51´ RQ
WKH UHPRWH FRQWURO XQLW DQG SUHVV

ENTER
3
:KHQ ³02'("´ DSSHDUV RQ WKH
UHPRWH FRQWURO XQLW SUHVV WKH
LQSXW VRXUFH VHOHFW EXWWRQ RI WKH
$9 HTXLSPHQW WKDW \RX ZDQW WR
VWRUH
• You cannot store the remote control code in
AMP
the button.
4
:KHQ ³.(<" ´ DSSHDUV RQ WKH UHPRWH FRQWURO XQLW
SUHVV WKH EXWWRQ WKDW \RX ZDQW WR VWRUH
• You cannot store the remote control code in the
POWER OFF ZONE SELECT SOURCE SELECT
, ,
SELECT 1 – 3 , BACK LIGHT and input source select button.
112
5
:KHQ ³6(1' ´ DSSHDUV RQ WKH UHPRWH FRQWURO XQLW
SODFH WKH UHPRWH FRQWURO XQLW RI WKH $9 HTXLSPHQW
IDFH WR IDFH ZLWK PDLQ UHPRWH FRQWURO XQLW RI WKLV
XQLW  1H[W SUHVV DQG KROG GRZQ WKH GHVLUHG EXWWRQ
WKDW \RX ZDQW WR VWRUH RI WKH UHPRWH FRQWURO XQLW RI
WKH $9 HTXLSPHQW
DQG
• When the button is correctly stored, "OK" flashes four times on
the remote control unit.
• If the button is not correctly stored, "FAIL" flashes four times on
the remote control unit. If this happens, perform step 4 again.
6
7R VWRUH DQRWKHU EXWWRQ UHSHDW VWHSV  DQG 
7
:KHQ \RX KDYH ¿QLVKHG VWRULQJ WKH UHPRWH FRQWURO
FRGHV SUHVV
"SET" flashes four times on the remote control unit and the
normal operation mode is restored.
POWER ON
,
• There are some remote control units that cannot be programmed,
MACRO QUICK
, ,
or even if they can be programmed, they may not operate correctly.
If this happens, use the remote control unit supplied with the AV
equipment to operate it.
• The operations of the programmed buttons override the preset
memory. If you do not require the programmed buttons, erase
the stored remote control codes to return to the initial settings
(vpage 112 "Operating learning function").
• The number of buttons that can be stored varies depending on the
remote control unit used. If you have stored the maximum number
of buttons allowed for the remote control unit, "FAIL" appears on
its display.

POWER ON
Operating the main remote control unit
n Erasing stored remote control codes
Erasing the code by each button
1
3UHVV DQG KROG DQG
POWER ON
IRU DW OHDVW 
ZONE/DEVICE ON
VHFRQGV
"SETUP" flashes twice on the remote
control unit.
2
8VH ui WR GLVSOD\ ³5(6(7´ RQ
WKH UHPRWH FRQWURO XQLW DQG SUHVV

ENTER
3
:KHQ ³/($51´ DSSHDUV RQ WKH
UHPRWH FRQWURO XQLW SUHVV
ENTER
4
:KHQ ³02'("´ DSSHDUV RQ WKH
UHPRWH FRQWURO XQLW SUHVV WKH
LQSXW VRXUFH VHOHFW EXWWRQ RI WKH
$9 HTXLSPHQW WKDW \RX ZDQW WR
HUDVH
5
8VH ui WR GLVSOD\ ³21("´ RQ WKH UHPRWH FRQWURO
XQLW DQG SUHVV 
ENTER
6
:KHQ ³.(<"´ DSSHDUV RQ WKH UHPRWH FRQWURO XQLW
SUHVV WKH EXWWRQ WKDW \RX ZDQW WR HUDVH
"RESET" flashes four times on the remote control unit and the
normal operation mode is restored.