Denon AVR-A100 Owner's Manual page 101

ENGLISH
Setting items
Crossover Freq. 40Hz / 60Hz / 80Hz / 90Hz / 100Hz / 110Hz / 120Hz / 150Hz / 200Hz /
Set the maximum frequency 250Hz : Set the crossover frequency.
of the bass signal output
Advanced : Specify crossover frequency for each speaker.
from each channel to
• Front / Center / Surround / Surr. Back / Front Height / Front Wide :
the subwoofer. Set the
Select the speaker.
Crossover Frequency to
• 40Hz / 60Hz / 80Hz / 90Hz / 100Hz / 110Hz / 120Hz / 150Hz / 200Hz /
suit the bass reproduction
250Hz : Set the crossover frequency.
capability of the speaker
being used.
• "Crossover Freq." can be set when the "Bass Setting" – "Subwoofer
Mode" (vpage 96) setting is "LFE+Main", or when you have a speaker
that is set to "Small".
• Always set the crossover frequency to "80Hz". When using small
speakers, however, we recommend setting the crossover frequency to
a higher frequency.
• For speakers set to "Small", sound below the crossover frequency
is cut from the sound output. The cut bass sound is output from the
subwoofer or front speakers.
• The speakers that can be set when "Advanced" is selected differ
depending on to the "Subwoofer Mode" setting (vpage 96).
• When "LFE" is selected, speakers set to "Small" at "Speaker Confi g."
can be set. If the speakers are set to "Large", "Full Band" is displayed
and the setting cannot be made.
• If set to "LFE+Main", this setting can be made regardless of the
speaker size.
Speaker Impedance 8Ω/ohms : Select when the impedance of the connected speaker is 8 Ω
Set the impedance of or more.
connected speakers. 6Ω/ohms : Select when the impedance of the connected speaker is at
least 6 Ω but less than 8 Ω.
4Ω/ohms : Select when the impedance of the connected speaker is at
least 4 Ω but less than 8 Ω.
Check the speaker impedance (Ω) shown on the back of your speakers
or in the instruction manual beforehand.
Front Speaker Setup 2CH DIRECT/STEREO : The front speakers used in the direct, stereo and
Set the front speakers to pure direct play modes (2 channel) are set in advance.
use for every surround • A : Front speaker A is used.
mode. • B : Front speaker B is used.
• A+B : Both front speakers A and B are used.
NOTE
MULTI CH : The front speakers used in modes other than the direct,
This can be set when
stereo and pure direct play modes (2 channel) are set in advance.
"Amp Assign" – "Assign
• A : Front speaker A is used.
Mode" is set to "Front B"
• B : Front speaker B is used.
(vpage 95).
• A+B : Both front speakers A and B are used.
98
Remote control operation
buttons
Setting details
Move the cursor
(Up/Down/Left/Right)
HDMI Setup
Make settings for HDMI video/audio output.
Setting items
RGB Range Normal : Output with RGB video range (16 (black) to 235 (white)).
Set the video range of RGB Enhanced : Output with RGB video range (0 (black) to 255 (white)).
output from the HDMI
This setting is active when using a TV equipped with a DVI terminal.
connector.
Vertical Stretch ON : Expand image signal in vertical direction.
Expand image signal in OFF : Do not expand signal in vertical direction.
vertical direction.
Auto Lip Sync ON : Compensated.
Make automatic OFF : Not compensated.
compensation for timing
shift in audio and video
output.
HDMI Audio Out Amp : Play back through speakers connected to the receiver.
Select HDMI audio output TV : Play back through TV connected to the receiver.
device.
When the HDMI control function is activated, priority is given to the TV
audio setting (vpage 65 "HDMI control function").
Monitor Out Auto (Dual) : The presence of a TV connected to the MONITOR 1 or
Make settings for HDMI MONITOR 2 terminal is detected automatically, and that TV connection
monitor output. is used.
Monitor 1 : A TV connected to the MONITOR 1 terminal is always used.
Monitor 2 : A TV connected to the MONITOR 2 terminal is always used.
• If both the Monitor 1 and 2 connectors are connected and "Resolution"
(vpage 84) is set to "Auto", the signals are output with a resolution
compatible with both TV.
• With "Resolution" (vpage 84) not set to "Auto",
check whether the TV you are using is compatible
with the resolution under "HDMI Information" –
"Monitor 1" and "Monitor 2" (vpage 107).
• You can also set "Monitor Out" by pressing
MONITOR SELECT
NOTE
Depending on the monitor you have connected, the display may not
be correct when you set to "Auto (Dual)". In such a case, set to either
"Monitor 1" or "Monitor 2".
Confi rm the setting
MANUAL SETUP
Default settings are underlined.
Setting details
.
Return to previous menu