Reset To The Default Setting (Except For Parental Setting); Troubleshooting Guide - Magnavox CMWD2206 - Owner's Manual

Reset to the Default Setting (Except for PARENTAL Setting)

1
Press [SETUP] in the stop
mode.
SETUP
STOP
<SETUP MENU>
SETUP
QUICK
CUSTOM
INITIALIZE

Troubleshooting Guide

g
If this unit does not perform properly when operated as instructed in this Owner's Manual, check this unit consulting the following checklist.
PROBLEM
No power. • Make sure the power plug is connected to an AC outlet.
• Make sure the power is turned on.
This unit does not respond to • Check if the power plug is connected to an AC outlet.
• Check the batteries in the remote control.
the remote control.
• Aim the remote control directly at the remote sensor. If necessary, remove all the obstacles between the sensor and the remote control.
• You have to be within 23 feet (7m) of this unit.
• Check if the right mode is selected. If it's not in the right mode, press [DVD] or [VCR], whichever you need, on the remote control.
• Check if a cassette tape is in this unit.
• Tune your radio to an empty AM station so that you hear a lot of noises. Turn the volume up, then if you hear some signal sound from the radio in
Poor picture or noise. • Interference signal may be received. Change the position and orientation of the unit.
Timer recording is impossible. • Make sure the Timer Recording is set correctly.
• Make sure TIMER REC indicator on the front panel lights up. If not, press [SUBTITLE/T-SET].
• Make sure the VCR clock is set correctly.
Cannot go into record mode. • Make sure the tape has a record tab. If needed, cover the hole with adhesive tape.
• Activate this unit in VCR mode. Press [VCR] on the remote control so that the VCR OUTPUT light is lit.
• Adjust tracking control for a better picture by pressing [CHANNEL L/K] on the unit or [SKIP/CH. G/K, H/L] on the remote control.
Playback picture is partially
noisy.
Cannot view a tape but the • Head cleaning may be necessary. Refer to "AUTO HEAD CLEANING".
• Make sure the VCR is not in the Menu mode.
audio is OK.
No or poor, playback picture. • Change the RF output channel to CH4. Then select the same channel on the TV.
• Fine tune your TV.
TV programs cannot be seen • Re-check the ANT-IN and ANT-OUT connections. See the front page and page 6.
• Press [VCR].
normally.
• Press [VCR] on the remote control to activate it in the VCR mode. Check if the VCR OUTPUT light is lit, then set it to the TV position by pressing [VCR].
Video or color fades in and • You cannot copy a copyrighted video tape. You are experiencing copy guard protection.
out when making a copy of a
video tape.
Cannot remove the tape. • Check if this unit is in the VCR mode. If not, press [VCR] on the remote control to switch the mode.
No picture. • Connect the video cable fi rmly.
• Insert a correct video disc that plays on this unit.
• Press [DVD] on the remote control. Check if the DVD OUTPUT light is lit. Then try other DVD features.
Disc cannot be played. • Insert the disc.
• Clean the disc.
• Place the disc correctly with the label side up.
• Cancel the parental lock or change the control levels.
• Handle a disc with special care so that it does not have fi ngerprints, scratches, or dusts on its surface.
No sound. • Connect the audio cable fi rmly.
• Turn the power of the audio component on.
• Correct the audio output settings.
• Correct the input settings on the audio component.
No DTS audio is output
• This unit does not support DTS audio.
-This is not a malfunction.
Distorted picture.
• Connect this unit directly to the TV.
• There are some cases where pictures may be slightly distorted, and those are not a sign of a malfunction.
• Although pictures may stop for a moment, this is not a malfunction.
Audio or subtitle language • The selected language is not available for audio or subtitles on the DVD.
-This is not a malfunction.
does not match the setup.
The camera angle cannot be • The DVD does not contain sequences recorded from diff erent camera angles.
-This is not a malfunction.
changed.
Audio or subtitle language • The DVD does not contain audio source or subtitles in the selected language.
-This is not a malfunction.
cannot be changed.
"Prohibited icon" appears on • That operation is prohibited by this unit or the disc.
-This is not a malfunction.
the screen, prohibiting an
operation.
• Some functions are not available in specific modes, but this is not a malfunction. Read the description in this Owner's Manual for details on correct
operations.
• Playback from a desired track and random playback are not available during program playback.
• Some functions are prohibited on some discs.
2
Select "INITIALIZE".
or
SETUP
QUICK
CUSTOM
INITIALIZE
Information
response to your pressing buttons on the remote control, the remote control is working.
3
Select "YES".
ENTER ENTER ENTER
SETUP INITIALIZE
Initialize?
NO
YES
CORRECTIVE ACTION
– 23 –
4
or
ENTER ENTER ENTER
Press Hint
twice.
• When you cancel to
initialize at step 3,
select "NO".
To exit the
menu
SETUP
EN