Whirlpool 8566930 Use And Care Manual page 20

Cabrio automatic washer
Hide thumbs Also See for 8566930:
Table of Contents

Advertisement

Available languages

Available languages

Was the cycle interrupted and then the Deep Clean option
selected?
The Deep Clean option should be started on a dry load only.
The Deep Clean option cannot be selected after the tub has
started filling with water.
Check household plumbing (laundry tubs, faucets,
drainpipe, water pipes) for leaks.
Dispenser operation
Are the laundry additives in the correct dispensers?
Add the correct amounts of detergent (powdered or liquid),
liquid chlorine bleach, or fabric softener to the correct
dispenser. You can add powdered or liquid color-safe bleach
to the detergent dispenser. Be sure to match powdered
color-safe bleach with powdered detergent or match liquid
color-safe bleach with liquid detergent. Use only liquid
chlorine bleach in the bleach dispenser.
Is there water remaining in the bottom of a dispenser?
Did the dispenser drain properly?
A small amount of water may be left in a dispenser at the end
of the cycle. This is normal.
Did you put powdered or liquid color-safe bleach into the
liquid chlorine bleach dispenser (on some models)?
Add powdered or liquid color-safe bleach directly to the
washer basket. Do not use the chlorine bleach dispenser for
color-safe bleach.
Is the fabric softener dispenser clogged?
Clean the fabric softener dispenser. See "Washer Care."
Washer Operation
WARNING
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
Washer won't fill, rinse or agitate; washer stops
Is the power cord plugged into a grounded 3 prong
outlet?
Plug power cord into a grounded 3 prong outlet.
Are you using an extension cord?
Do not use an extension cord.
20
Is there power at the plug?
Check electrical source or call electrician.
Is the indicator on the Cycle control knob properly lined
up with a cycle?
Turn the Cycle control knob to the right slightly.
Are the water inlet valve screens clogged?
Turn off the water and remove inlet hoses from the washer.
Remove any accumulated film or particles. Reinstall hoses,
turn on water and check for leaks.
Are the hot and cold water faucets turned on?
Turn on the water.
Is the water inlet hose kinked?
Straighten the hoses.
Does the water level seem too low, or does the washer
appear to not fill completely?
The Auto Water Level feature senses the size of the load and
adds the correct amount of water for the load size.
Are you using Auto Water Level?
The Auto feature senses the size of the load and adds the
correct amount of water for the load size.
Has a household fuse blown, or has a circuit breaker
tripped?
Replace the fuse or reset the circuit breaker. If the problem
continues, call an electrician.
Is the washer in a normal pause in the cycle?
The washer may pause during certain cycles. Allow the cycle
to continue.
Is the washer overloaded?
Wash smaller loads. See "Starting Your Washer" for
maximum load size.
Is there oversudsing?
Cancel the current cycle. Select DRAIN & SPIN to drain the
load. Re-select your desired cycle and press START. Do not
add detergent. Use cold water.
Is the lid open?
The lid must be closed during operation. The washer will not
operate with the lid open.
Did you add more items to the load once the washer
started?
Once the load is wet, there may appear to be space for more
items. Do not add more than 1 or 2 garments after the cycle
has started. For best results determine load size with dry items
only.
Washer continues to fill or drain, or the cycle seems
stuck
Is the top of drain hose lower than the control knobs on
washer?
The top of the drain hose must be at least 39" (99 cm) above
the floor. See "Drain System."
Does the drain hose fit too tightly in the standpipe, or is it
taped to the standpipe?
The drain hose should be loose yet fit securely. Do not seal
the drain hose with tape. The hose needs an air gap. See
"Installation Instructions."
Washer won't drain or spin; water remains in washer
Is the drain hose clogged, or the end of the drain hose
more than 96" (244 cm) above the floor?
See "Drain System."

Advertisement

Table of Contents
loading

Table of Contents