Page 1
Instructions for Use Anti-theft alarm DWA 6 BMW Motorrad The Ultimate Riding Machine...
Page 2
Motorcycle data/dealership details Motorcycle data Dealership details Model Person to contact in Service department Vehicle identification number Ms/Mr Colour code Phone number Date of first registration Dealership address/phone number (com- Registration number pany stamp)
Page 4
BMW recommends *01417714371* Order No. 01 41 7 714 371 *01417714371* 05.2008, 5th edition...
Page 5
BMW Motorrad anti-theft alarm, your authorised BMW Mo- torrad dealer will gladly provide advice and assistance. We hope that you will enjoy us- ing your DWA 6 system and that all your journeys will be pleasant and safe. BMW Motorrad.
Table of Contents You can also consult the index at 4 Technical data ..17 the end of this Rider's Manual if Anti-theft alarm....18 you want to find a particular topic Remote control.
Overview Nor can BMW Motorrad entirely Instruction. rule out errors and omissions. Chapter 2 of these instructions Result of an activity. We hope you will appreciate that for use will provide you with no claims can be entertained on an initial overview of the anti-...
General information Controls matically a few days after being activated. In most cases, how- about the anti-theft ever, it will remain active for at alarm least seven days. Any attempt to move the motor- Radio interference cycle, change its position, start Radio systems or devices trans- it without an authorised key or mitting on the same frequency...
Activation Alarm tone sounds twice (if for longer than one second. If it programmed). is left deactivated for longer than Activating with motion approximately one hour, the anti- The telltale light on the mo- sensor theft alarm shuts itself down in torcycle starts flashing (0.1 order to conserve battery power.
Deactivating motion Alarm function Alarm sensor Alarm triggers An alarm can be triggered by the motion sensor an attempt to switch on the ignition with an unauthorised an attempt to disconnect the anti-theft alarm from the starter battery (the built-in battery in An alarm lasts for 26 seconds.
Reason for an alarm Acoustic indication that Note that you can deactiv- ate the alarm function with alarm was triggered Once you have deactivated the the ignition key only when the kill alarm function, the anti-theft A signal tone sounding once switch is in the RUN position.
order for the alarm function to be Alarm tone sounds as confirm- Within ten seconds, switch off deactivated. ation after activation/deactiva- the ignition. tion of the alarm function: No Press button 2 three times. Programming Alarm tone: Intermittent Acknowledgement tone sounds Automatic activation of the once.
Saving programmed Step 1: Do you want a con- Yes: firmation tone to sound after settings Press button 1. activation/deactivation of the Programming is saved anti-theft alarm? when the ignition is switched Press button 2. Yes: off after completion of the last Press button 1.
the remote control units with the Termination of Acknowledgement tone sounds anti-theft alarm. You can register once. registration a maximum of four remote con- Within ten seconds, switch on Registration is terminated when trol units. the ignition. four remote control units have Acknowledgement tone sounds been registered Registering remote...
Battery Synchronisation Synchronising remote control When is it necessary to When does the battery synchronise the remote have to be changed? control? The battery in the remote control is due to be changed after ap- The remote control has to be proximately 2 - 3 years.
Page 19
Using a battery of the wrong type or inserting the battery with the polarity reversed can cause irreparable damage to the device. Use only the specified type of battery (see "Technical Data"). When inserting the battery, always make sure polarity is correct.
Anti-theft alarm Time to active after activation 15 s Alarm duration 26 s Activation time between two alarms 12 s Temperature range -40...85 °C Operating voltage 9...16 V Remote control Range of the remote control 10 m Reception standby for signal from remote control 1 h, After ignition off Signal frequency 25 kHz, Broadband...
Page 23
Abbreviations and symbols, 4 Registration Remote control, 13 Activating Remote control with motion sensor, 8 registering, 13 Alarm function Deactivating, 10 synchronising, 14 Battery Technical data Standards, 4 changing, 14 Currency, 4 Deactivating Alarm, 10 Motion sensor, 9 Default settings, 11 Motion sensor Deactivating, 9 Programming, 11...