Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for BMW DWA 5
Summary of Contents for BMW DWA 5
- Page 1 Supplementary Rider’s Manual DWA 5 Anti-Theft Alarm System...
- Page 2 Note: Warning: This symbol indicates pre- cautions and measures which are essential in order to pro- tect the rider and other per- sons from possibly severe or fatal injury.
- Page 4 BMW recommends Castrol...
-
Page 5: Welcome To Bmw
Welcome to BMW instructions for use, and we Congratulations on your pur- would like to take this opportu- chase of this BMW anti-theft nity of sending you our very alarm. best wishes. It acts as a deterrent for poten-... -
Page 6: Table Of Contents
Contents 5 Lights i Introduction Lights........23 Welcome to BMW ....1 General ......... 3 6 Programming Customising the anti-theft 1 Overview and operation alarm system ...... 24 Controls ........ 4 Default settings ....25 Functions of the remote Accessing the control unit ...... -
Page 7: General
General Your anti-theft alarm is com- bined with a central locking sys- tem that enables you to open and close the cases, the top- case, and the radio compart- ment by remote control. It also enables you to switch on the map-reading light and the Any attempt to move the motor- ground lights automatically. -
Page 8: Controls
Controls Note: Do not be tempted to use the remote control unit to lock the keys inside a stowage compart- ment. If you were to mislay the remote control unit the keys 1 Left button (ribbed) would be inaccessible and you 2 Right button would be able neither to open 3 LED... -
Page 9: Functions Of The Remote Control Unit
Functions of the remote control unit Operation Button 1 Confirmation Press once Lock central locking – Press again Activate alarm func- Turn indicators flash tion and immobiliser 2x Alarm tone sounds 2x (if pro- grammed) Press for third time Deactivate motion Indicators flash 3x sensor (for transport, Alarm tone sounds... -
Page 10: Code Card
BMW motorcycle card with the vehicle registra- dealer will be able to forward tion papers, and carry both with the encrypted number to BMW you when you ride the motorcy- on your behalf and obtain the cle. correct code. -
Page 11: Activation
Activation Once the immobiliser has been activated the engine will refuse to start even if an authorised key is used for the start attempt. You can tell whether the immobiliser is activated by switching on the ignition and observing LED 5; if the immobi- liser is active it will light up when the pre-ride check completes. - Page 12 • by the indicators flashing Contact your authorised BMW twice motorcycle dealer if the alarm tone sounds four times on acti- • by the alarm tone sounding...
-
Page 13: Deactivation
Deactivation Deactivating the immobi- liser with the remote con- If confirmation takes the form of trol unit the alarm tone sounding four The immobiliser is deactivated times, this is to indicate that the • by pressing button 2 on the voltage in the on-board elec- remote control unit once (if tricity supply has dropped... -
Page 14: Activation
Activation Activation with motion sensor The alarm function is activated • by pressing button 1 on the remote control unit twice • by switching off the ignition, if programmed ( Activation is confirmed When you switch off the igni- • by the indicators flashing tion, 50 seconds elapse before twice activation. - Page 15 Activation You deactivate the motion sen- • by pressing button 1 on the remote control unit for a sec- Deactivating the motion ond time within the activation sensor phase ( If, for example, you want to transport your motorcycle by Deactivation is confirmed train, it is advisable to deacti- •...
-
Page 16: Activation Phases
Activation phases 15 seconds elapse before the alarm function is fully active. Status of the anti- theft alarm Activation phase Rapid flashing (15 seconds) (0.1 sec. on/ 0.5 sec. off) If the motion sensor was switched off: Rapid flashing (0.1 sec. on/ 0.2 sec. off) Anti-theft alarm Slow flashing active... -
Page 17: How The Alarm Is Triggered
How the alarm is triggered Alarm An alarm lasts for 26 seconds. The alarm function is active again 12 seconds later. If the reason for the alarm persists, the alarm function is triggered again, but this can happen no How the alarm is triggered more than five times in succes- The alarm can by triggered sion. -
Page 18: Deactivation
Deactivation Deactivating the alarm function with the remote control unit The alarm function is deacti- vated • by pressing button 2 on the remote control unit once Deactivation is confirmed If the alarm function was acti- • by the turn indicators flashing vated automatically beforehand once when you switched off the igni-... - Page 19 Deactivation Deactivating the alarm function without remote control unit If you do not have the remote control unit to hand when the anti-theft alarm is active, you Note: can still deactivate the system. The system will permit a maxi- To do so, you will need the mum of 3 successive attempts;...
-
Page 20: Reasons For An Alarm
Reasons for an alarm Reasons for an alarm Once you have deactivated the alarm function, the LED shows you reasons for alarms, if any, that were triggered in your absence: • Flashes 1x: Motion sensor • Flashes 2x: The LED ceases to output this Ignition on while the anti-theft signal after 1 minute, or as soon alarm was primed... - Page 21 Reasons for an alarm You can also check the system at some subsequent time in order to ascertain the reason why the most recent alarm was triggered. In order to do so, you must first identify yourself by means of your code number. If you now switch off the igni- tion, the LED will flash to indi- If the code number you entered...
- Page 22 Reasons for an alarm Step Action Confirmation Deactivate the anti-theft alarm and switch on the ignition Within 4 seconds, switch the LED on, ignition off and immediately on 1x acknowledgement again THREE TIMES in succes- tone sion Switch the ignition off within 15 LED flashes seconds and then observe the Count the LED flashes until the...
-
Page 23: Manual Operation
Manual operation Manual opening and closing You can still open and close the cases, the topcase and the radio compartment manually with the key, as described in the Rider’s Manual. -
Page 24: Remote Control Unit
Remote control unit Opening with the remote control unit Press button 2 on the remote control unit once to unlock the cases, the topcase and the Closing with the remote radio compartment. A lock that control unit was engaged manually remains Press button 1 on the remote locked even after opening with control unit once to lock the... -
Page 25: Emergency Unlocking
Emergency unlocking If the compartments were locked by the central locking system and, for some reason, the remote control unit is not to hand, you can use the emer- gency unlocking routine to 3 You can now press in the open them. -
Page 26: Safety Shutdown
Safety shutdown Overly frequent locking and unlocking within a short period of time could cause the motors of the central locking system to become very warm. An override function can cut in and interrupt operation in order to avoid damage to the motors: these interruptions can last for a max- imum of 30 seconds. -
Page 27: Lights
Lights The lights are switched on • when you deactivate the alarm function • by switching off the ignition, if programmed ( Map-reading light The map-reading light switches The lights dim out after on automatically if switch 1 is in 20 seconds. -
Page 28: Customising The Anti-Theft Alarm System
Customising the anti-theft alarm system You can customise the BMW anti-theft alarm system to suit your needs and preferences as follows: • Acoustic confirmation after activation/deactivation of the anti-theft alarm in addition to turn indicators flashing • Automatic activation of lights when ignition is switched off •... -
Page 29: Default Settings
Default settings Setting Status Acoustic acknowledgement after activation/ deactivation Automatic activation of lights when ignition is switched off Type of acoustic alarm Intermittent Automatic activation of alarm function when ignition is switched off Automatic activation of immobiliser when igni- tion is switched off... -
Page 30: Programming Mode
Programming mode, accessing Step Action Confirmation Deactivate the anti-theft alarm Steps 3 to 7 must be com- pleted within 10 seconds Switch on the ignition Wait until LED 5 goes out Press button 2 once LED lights up briefly Switch off the ignition LED shows the number of registered remote control units... -
Page 31: Programming
Programming The number of times LED 5 flashes indicates the step to which you have progressed in programming. An alarm tone sounds as confir- mation when you press button 1, whereas an acknowl- edgement tone sounds when you press button 2. The LED stops flashing and four acknowledgement tones sound when you complete the final... -
Page 32: Exiting Programming Mode
Exiting programming mode Note: Note that you cannot activate the function for priming the alarm automatically when the Programming is saved ignition is switched off unless • by switching off the ignition the system is also set up for au- after the final step is com- tomatic activation of the immo- pleted... -
Page 33: Remote Control Units
Registering remote control units If you want to start using an extra remote control unit or replace a remote control unit that has been mislaid, you Note: always have to register all the The LED flashes when the igni- remote control units with the tion is switched off: the number anti-theft alarm. - Page 34 Registering remote control units If the code number you entered Starting point You must begin by identifying is correct, two acknowledge- yourself by means of your code ment tones sound to indicate number. that identification is completed. Step Action Confirmation Deactivate the anti-theft alarm and switch on the ignition Within 4 seconds, switch the...
- Page 35 Registering remote control units You can now register a maxi- mum of four remote control units with the anti-theft alarm. Step Action Confirmation Press and hold down buttons 1 LED 3 flashes and 2 LED stops flashing after 10 seconds Release buttons 1 and 2 LED ON Press button 1 or 2...
-
Page 36: Exiting Registration Mode
Exiting registration mode Registration terminates The LED flashes and the • once four remote control units acknowledgement tone sounds have been registered three times when registration • if the ignition is switched off ends. The number of times the • if, after a remote control unit LED flashes after the ignition is has been registered, 30 sec- switched off corresponds to the... -
Page 37: Synchronising The Remote Control Unit
Synchronising the remote control unit Synchronisation is necessary if the buttons on the remote con- trol unit are pressed more than 256 times outside the range of the receiver. When this limit is reached the receiver on the motorcycle no longer reacts to signals from the remote control unit. -
Page 38: Changing The Battery
Changing the battery Attention: Use only CR 2032 3V lithium Changing the batteries in the remote control units batteries. Take care not to reverse polari- The batteries in the remote con- ty when inserting the batteries. trol units are due for replace- Inserting batteries of a different ment after approximately 2 to 3 type or inserting the batteries... - Page 39 Changing the battery • Remove screw 6 and lift off the bottom section of housing 7 • Slide the spent battery 10 out from underneath retainer 8 and insert the new battery – making sure the positive terminal is up •...
-
Page 40: Technical Data
Technical data Anti-theft alarm Neutral activation time 15 seconds Alarm duration 26 seconds Neutral time between two 10 seconds consecutive alarms Operating temperature –40 °C to +85 °C ±0.7° Trigger angle of the motion sensor Current consumption (idle < 3 mA current with system active) Operating voltage 9–16 V... -
Page 41: Index
Index Activation phases, 12 Manual operation, 19 Activation with motion sensor, 10 Motion sensor, 11 Alarm, 13 Alarm function Deactivating with remote Programming, 26, 27 control unit, 14 Deactivating without remote control unit, 15 Remote control closing, 20 opening, 20 Changing the battery, 34, 35 Remote control unit Code card, 6...