Welcome to BMW instructions for use, and we Congratulations on your pur- would like to take this opportu- chase of this BMW anti-theft nity of sending you our very alarm. best wishes. It acts as a deterrent for poten-...
Customising the anti-theft alarm........12 Default settings ....13 Accessing the Introduction programming mode .... 14 Welcome to BMW ....1 Programming ...... 15 General ......... 3 Exiting programming mode ...16 Overview and operation Remote control units Controls ........ 4...
General Any attempt to move the motor- You can customise the anti- cycle, change its position, start theft alarm in certain ways to it without your permission, or suit your needs and prefer- disconnect the battery will trig- ences. ger the alarm. The sensitivity of the system is set in such a way that slight vibrations of the Note:...
Controls 1 Left button (ribbed) Refer to the Rider’s Manual to 2 Right button ascertain precisely where the 3 LED status LED is installed on your 4 Radio remote control unit motorcycle.
Functions of the remote control unit Operation Button 1 Confirmation Press once Activate alarm func- Indicators flash 2x tion Alarm tone sounds 2x (if programmed) Press again Deactivate motion Indicators flash 3x sensor (for transport, Alarm tone sounds for example) Operation Button 2 Confirmation...
Activation Activation with motion sensor The alarm function is activated • by pressing button 1 on the If you decide to activate the remote control unit once alarm function more than one minute after switching off • by switching off the ignition (if the ignition, you must press programmed ( 15))
Page 8
Activation You deactivate the motion sen- • by pressing button 1 on the remote control unit for a sec- Deactivating the motion ond time within the activation sensor phase ( If, for example, you want to transport your motorcycle by Deactivation is confirmed train, it is advisable to deacti- •...
Activation phases 15 seconds elapse before the alarm function is fully active. Status of the anti-theft alarm Anti-theft alarm telltale light Activation phase (15 seconds) Slow flashing (0.1 sec. on / 0.9 sec. off) Anti-theft alarm active...
Alarm Alarm An alarm lasts for 26 seconds. The alarm is active again 12 seconds later. You can can- Triggering the alarm cel an alarm at any time after it The alarm can by triggered has been triggered by pressing •...
Deactivating the alarm function Deactivating the alarm function Deactivation is confirmed The alarm function is deacti- • by the turn indicators flashing vated once • by pressing button 2 on the remote control unit once (if • by the alarm tone sounding the alarm function was acti- once (if programmed ( 15))
Reasons for an alarm Reasons for an alarm Once you have deactivated the alarm function, the anti-theft alarm telltale light is active for a period of one minute to show you reasons for alarms, if any, that were triggered in your absence: •...
Customising the anti-theft alarm You can customise the BMW anti-theft alarm system to suit your needs and preferences as follows: • Acoustic confirmation after activation/deactivation of the anti-theft alarm in addition to turn indicators flashing • Rising and falling or intermit- tent acoustic alarm •...
Default settings Setting Status Acoustic confirmation after activation/deactiva- tion Type of acoustic alarm Intermittent Automatic activation of alarm function when ignition is switched off...
Programming mode, accessing Step Action Confirmation Deactivate alarm function Ignition ON Press button 1 three times 1x acoustic acknowledge- ment Switch ignition OFF within 10 seconds Press button 2 three times 1x acoustic acknowledge- ment Switch ignition ON within 3x acoustic acknowledge- 10 seconds ment The programming function is...
Programming The number of times the anti- theft alarm telltale light flashes indicates the step to which you have progressed in program- ming. An alarm tone sounds as confir- mation when you press button 1, whereas an acknowl- edgement tone sounds when you press button 2.
Exiting programming mode Programming is saved • by switching off the ignition after the final step is com- pleted • automatically 30 seconds Programming mode is after completion of the final cancelled step • by switching off the ignition before the final step is com- Four acknowledgement tones pleted sound to indicate that you have...
Registering remote control units If you want to start using an extra remote control unit or replace a remote control unit that has been mislaid, you always have to register all the remote control units with the anti-theft alarm. You can regis- ter a maximum of four remote control units.
Page 19
Registration mode, accessing Step Action Confirmation Deactivate alarm function Switch on the ignition Press button 2 three times 1x acoustic acknowl- edgement Switch ignition OFF within 10 seconds Press button 2 three times 1x acoustic acknowl- edgement Switch ignition ON within 2x acoustic acknowl- 10 seconds edgement...
Page 20
Registering the remote control unit You can now register a maxi- mum of four remote control units with the anti-theft alarm. Step Action Confirmation Press and hold down buttons 1 LED 3 flashes and 2 LED stops flashing after 10 seconds Release buttons 1 and 2 LED ON Press button 1 or 2...
Exiting registration mode Registration terminates • once four remote control units have been registered • if the ignition is switched off • if, after ignition OFF, 30 sec- onds elapse without a button being pressed • if, after a remote control unit The LED flashes and the has been registered, 30 sec- acknowledgement tone sounds...
Synchronising the remote control unit Synchronisation is necessary if the buttons on the remote con- trol unit are pressed more than 256 times outside the range of the receiver. When this limit is reached the receiver on the motorcycle no longer reacts to signals from the remote control unit.
Changing the battery Attention: Use only 3 V type CR 2032 lith- Changing the batteries in ium batteries. the remote control units Take care not to reverse polari- The batteries in the remote con- ty when inserting the battery. trol units are due for replace- Inserting a battery of a different ment after approx.
Changing the battery • Remove screw 6 and lift off the bottom section of the housing 7 • Slide the spent battery 10 out from underneath the retainer 8 and insert the new battery – making sure the positive terminal is up •...
Technical data Anti-theft alarm Neutral activation time 15 seconds Alarm duration 26 seconds Neutral time between two con- 12 seconds secutive alarms Operating temperature –40 °C to +85 °C (–40 °F to +85 °F) ±0.7° Trigger angle of the motion sen- Current consumption (idle cur- <...
Page 26
A - Z Activation phases, 8 Technical data, 24 Activation with motion sensor, 6 Triggering the alarm, 9, 11 Alarm, 9 Alarm function Deactivating, 10 Changing the battery, 22, 23 Controls, 4 Customising the anti-theft alarm, 12 Default settings, 13 Functions of the remote control unit, 5 Motion sensor, 7...