Washing Instructions; Maintenance Advice - Chicco HOOK ON CHAIR QUICK ADJUST Manual

Quick adjust

Hide thumbs

Table of Contents

Available languages

Enlarged version

OOK ON

The instructions contained in this booklet also apply to the

CADDYLINE version.

WARNING

• WARNING: Never leave your child unattended.

• Age range: from around 6 months up to babies of 15 Kg.

• Only use with babies able to take up a correct and

independent sitting position.

• Do not use on glass, crystal or similar table surfaces, or

rough or uneven surfaces, tables with a single leg, games

or camping tables. Do not use on table extensions.

• Do not ﬁ x the table seat in places where the baby

could use its feet to push against the table, chairs or

other structures causing the seat to shift and become

unstable.

• Before using always make sure that the joints are

securely screwed to the table.

• Do not hang objects on the seat which could make the

seat unstable.

• Do not ﬁ x or unﬁ x the seat with the baby inside.

• Do not use the seat with more than one baby at a time.

• Do not let other children play unattended close to the

seat.

• Do not use or leave table cloths or other objects on the

table surface which could interfere with the components

which ﬁ x the seat to the table. Keep the table surface

clean and dry.

• Check the table is stable when the seat is ﬁ xed in place.

• The table top must have a minimum thickness of 19 mm.

and a maximum of 38 mm.

• Frequently check that the ﬁ xing pins are screwed in

securely and tighten if necessary.

• WARNING: do not use the seat if parts are broken,

damaged or missing.

• Do not use spare parts not supplied by the

manufacturer.

• WARNING: Keep all plastic bags out of reach of the child

to avoid the risk of suffocation.

ASSEMBLY

Join the two arms (diag. A) to the table seat frame. Proceed

as follows: Join the arm with the red symbol to the side of the

seat (diag. B) with the red arrow (as shown in diag. 1). Connect

the arm and ensure that that both of the pins are locked into

position (diag. 2). A double click will indicate that the pins are

locked correctly into position. Repeat the operation on the

other arm. Fix both the cover fastenings with the automatic

studs by passing them around the frame (Fig. 3). Make sure the

upper stud is used. Check that the fabric armrests are correctly

ﬁ xed to the lower catches (Fig. 4) (no Caddy). These are situated

immediately below and in line with the catches indicated in

the previous operation above. It is possible that the two arms

inserted remain "open", in the ready-for-use position. If you do

not wish to use the product immediately, just press the "pins"

shown in ﬁ g. 5, on both sides to close the arms.

HOW TO USE

Open the two arms (Fig. 6) and make sure that they are

securely ﬁ xed in an open position by trying to close them.

Press the catches on the lower joints and push the pins in a

downward direction (Fig.7). Incline the table seat by raising the

rear section and position it on the table surface (Fig.8). Push

HAIR

until it comes to a halt (Fig.9).Push the joint pin upwards until

it makes contact with the table surface (Fig.10/10A). Repeat

this operation with the other joint.Make ﬁ nal adjustments

by rotating the handgrips situated under the joints in an

ANTICLOCKWISE direction, until the seat is securely ﬁ xed (Fig.

11). Repeat this operation with both the handgrips. Check they

are securely ﬁ xed by pushing the seat away from the table.

Unfasten the double safety belt and seat the child (Fig. 12).

Fasten the safety belt by passing it through the crotch strap.

Do not place chairs or similar objects under the table seat while

in use. Detach the seat from the table only after removing the

child. To remove the table seat from the table, turn the knob

in a CLOCKWISE direction until the initial position is reached.

Then press the buttons on the joints and the locking pins will

unlock automatically. If necessary, exert gentle pressure on the

knobs.

REMOVABLE LINING

Unfasten the catches of the cover (Fig.13).

Unﬁ x the two arms by pressing the two pins on both sides

(Fig.14/14A).

Unfasten the waist harness from the "D" rings and pass them

inside the fabric. At this point it is possible to remove the cover

from the frame. Repeat the operation in reverse to replace the

cover, being careful that the harness passes through the "D"

rings correctly (Fig.15).