Cleaning Instructions - Chicco 360 Instructions For Use Manual

GB
TABLE SEAT
IMPORTANT: FOR YOUR CHILD'S SAFETY: PLEASE READ
THESE INSTRUCTIONS CAREFULLY BEFORE USE AND KEEP
THEM FOR FUTURE REFERENCE. YOUR CHILD MAY BE HURT
IF YOU DO NOT FOLLOW THE INSTRUCTIONS.
WARNING! KEEP COVERINGS AWAY FROM BABIES AND
CHILDREN TO AVOID SUFFOCATION.
WARNINGS
• WARNING! Never leave the child unattended in this table
mounted chair.
• The table mounted chair shall not be used by children wei-
ghing more than 15 kg.
• The table mounted chair is not suitable for children who can-
not sit unaided.
• Do not use on glass, or loose table top, table leaf or single
pedestal or card table or camping tables.
• Do not fi t the table seat to drawers or movable parts of ta-
bles.
• Do not attach the table mounted chair where the child
might use its feet to push against a part of the table, another
chair or any other structure as this could cause the table seat
to come off the table.
• Routinely check any clamping screws, fi xing joints and
tighten them, if required.
• Do not attach objects to the table seat, since they might af-
fect the stability and safety of the product.
• Do not carry out any fi tting or locking operations with the
child sitting in the table seat.
• Do not seat more than one child at a time in the table seat.
• Do not let other children play unattended close to the table
seat.
• Do not use tablecloths or other objects on the support surfa-
ce which might interfere with the proper functioning of the
anchoring elements. Keep the table structure and surface
clean and dry.
• Check that the table will not tip over when the table mounted
chair, attached to it, is in use.
• The product must be fi tted to table surfaces with a minimum
thickness of 19mm and maximum thickness of 90mm.
• WARNING! Do not use the table mounted chair if any com-
ponents are broken or missing.
• Do not use replacement parts other than those approved by
the manufacturer or distributor.
• WARNING! Keep covering away from babies and children to
avoid suffocation.
• WARNING! Always use the safety harness.

CLEANING INSTRUCTIONS

• This product requires regular maintenance.
• The cleaning and maintenance of the table seat must only be
carried out by an adult.
• Periodically check the table seat for wear, damage, or mis-
sing components. Should any parts be missing or damaged,
the table seat must not, under any circumstances, be used.
• Always dry the metal parts to prevent the formation of rust.
• It is recommended to periodically clean space between the
movable and fi xed plastic parts of the seat with a toothbrush
to remove any possible food residues.
• Please refer to the care label for instructions on cleaning the
fabric cover.
Wash by hand in cold water
Do not bleach
Do not tumble dry
Do not iron
Do not dry clean
COMPONENTS
A – Table seat (diagram 1)
B – Movable part of the seat (diagram 1)
C – Fixed part of the seat (diagram 1)
D – Handle (diagram 1)
E - F – Arms (diagram 2)
G – Rear fi xing joints (diagram 2)
GG – Rear joint buttons (diagram 2)
GGG – Rear joint screws (diagram 2)
H – Front fi xing joints (diagram 2)
HH – Front joint buttons (diagram 2)
I – Non-Slip Plastic Parts
HOW TO ASSEMBLE THE TABLE SEAT
1. Remove the table seat from the mesh bag.
2. Join the two arms (E, F) to the table seat frame. Insert one
arm at a time into the tube of the frame, as shown in Diagram
3, ensuring that the two locking buttons located on the tube
of the frame have completely come out from the holes
located on the arm (E-F). A click will be heard, indicating
that they are fi tted correctly into position (see diagram 4).
Warning! To make the assembly operations easier, a screen-
printed symbol is present on one of the two arms and one
tube of the frame to indicate that the two parts must be
joined together.
Repeat the operation on the other arm.
HOW TO USE THE TABLE SEAT
3. To fi x the seat to the table, turn the screws of the joints
(GGG) in a clockwise direction, as shown by the screw symbol
(see diagram 5).
4. Press the buttons located on the joints ( GG – HH) (see
diagram 6), until the joints are completely lowered. Incline
the table seat, raising the rear part, and place it on the table
surface (diagram 7). Push the table seat into position.
5. Push the four joints upwards (G-H) until they are in contact
with the underside of the table top (diagram 8).
6. Carry out the fi nal adjustments turning the screws (GGG)
in an ANTICLOCKWISE direction, until the table seat is fi xed
correctly into position (diagram 9). Now check that the non-
slip plastic parts (I) adhere correctly to the table surface.
If they do not adhere correctly, it is necessary to further
tighten the clamping screws (GGG), always in anti-clockwise
direction, until the non-slip plastic parts adhere to the table
surface completely. Pull the seat outwards to check whether
it is safely locked into position. The table set is now ready
for use.
13