Advertisement
aprilia
DEALER INSTRUCTION SHEET
2
5
BATTERY
Battery electrolyte is toxic, caustic and the contact
with the skin may cause serious burns, since it
contains sulfuric acid. Wear protective clothing, a
face shield and/or tight fitting goggles when
working around the battery. In case of contact with
the skin, flush immediately with plenty of water.
In case of contact with the eyes, flush with plenty
of water for at least 15 minutes. Immediately
consult an oculist.
If the electrolyte is accidentally swallowed, drink
large quantities of water or milk, and then milk of
magnesia or vegetable oil. Immediately consult a
health professional. The battery gives off noxious
and explosive gases; keep it away from cigarettes,
flames, sparks and any other source of heat.
During the recharging or the use, make sure hat
the room is properly ventilated and avoid inhaling
the gases released during the recharging.
KEEP AWAY FROM CHILDREN.
SR 50 DITECH
6
1
3
5
4
Do not tip the vehicle too much, or tip the battery
too much, to avoid electrolyte leaking out.
CAUTION
The battery liquid is corrosive. Do not pour or
sprinkle it, particularly on plastic parts. When the
battery has been removed it must be placed in a
safe place out of the reach of children. The battery
is very dangerous and may cause serious injury
or death.
INITIAL BATTERY CHARGING
CAUTION
Remove the tool kit cover (1) turning the key (2)
clockwise.
Remove the tool kit carrier (3) and the battery (4).
Remove the plug (5) from the recharge container (6).
Fit the container into the battery as shown in the
drawing (see the battery instructions in the recharge
pack).
Use the same plug (5) to stop up battery holes.
FITTING THE BATTERY
CAUTION
Make sure the ignition
key is in the "
" position.
Place the battery into its housing.
First connect the positive cable (+ red) then the ne-
gative (- blue).
Use a neutral grease or vaseline to grease terminals.
Fit the tool kit carrier and cover.
Pag. 2
aprilia
DEALER INSTRUCTION SHEET
3
2
4
FITTING THE MIRRORS
Fit the mirrors as follows.
To fit the right wing mirror position the gasket (1)
marked "DX" and the mirror (2), then tighten with
screw TCEI M 8x35 (3).
Screw (3) tightening torque: 18,44 ftlb (25 Nm)
Close the hole in the mirror with the rubber plug (4).
Do the same for the righthand mirror.
FITTING THE FRONT WHEEL
DANGER
Before carrying out any maintenance operation or
inspection of the front wheel, if possible hoist the
vehicle onto a solid and level surface with suitable
equipment.
When disassembling and reassembling the front
wheel, take extra care not to damage the brake
lines, discs or pads.
IMPORTANT
IMPORTANT To fit the front wheel, you may require a
helper.
SR 50 DITECH
1
A
4
B
To fit the wheel, remove the brake gripper (1)
removing screws TEF M 8x35 (2).
Fit the wheel, positioning the tongues (A) of the
speedometer transmission into the housing on the
wheel hub.
Fit the tooth (B) of the speedometer transmission
between the two anti-rotation pegs on the fork.
Make sure the transmission is properly fitted into
the wheel hub.
CAUTION
Make sure the spacer (3) between the wheel hub
and left rod is inside the fork.
Fit the wheel pin (4) and washer (5) and secure the
nut M10 (6)
Nut (6) tightening torque: 36,87 ftlb (50 Nm).
Fit the brake gripper (1) with the screws (2).
Screw (2) tightening torque: 19,91 ftlb (27 Nm).
Tighten the two screws TCEI M 6x20 (7) of the wheel
pin terminal to 8.85 ftlb (12 Nm).
Pag. 3
1
2
5
6
3
Advertisement
