Usb Operation; Folder Selection - LENCO SCR-187 Instruction Manual

FOR MP3/WMA/USB PLAYBACK
Programmed playback enables tracks on a disc to be played in the desired order. Up to 20 tracks can be programmed.
1. Program mode works in STOP mode only.
2. Holding RANDOM / P - / PROGRAM / MEMORY button for 2 seconds to enter program mode. The "PROG" icon will
be turned on. "00 000 P01" will be shown with "00" flashing. "000" represents track number and "P:01" represents
program location number.
3. Press the TUNE + / NEXT or TUNE - / BACK button to select the desired folder.
4. Press TUNE + / NEXT or TUNE - / BACK button to select the required track number.
5. Press RANDOM / P - / PROGRAM / MEMORY button to confirm the track number.
The display will show the next program number "000 P02". The track number will be
flashing again and waiting for track number input.
6. Repeat steps 3 and 4 until all the desired tracks has been programmed or all the
program memories have been used. It will loop back to P01 after all the program
memories have been used. Same track number can be programmed more than once.
7. Press ENTER/PLAY/PAUSE button to playback.
8. To clear the programmed tracks, first press RANDOM / P - / PROGRAM / MEMORY button for 2 seconds to enter
program mode.
9. Press STOP button to clear all the programmed memories.

USB OPERATION

1. Connect USB player into the USB input of the system.
2. Press FUNCTION button repeatedly until "UDISK" is shown on the
display. After entered the corresponding mode, the corresponding icon
will be lit up.
3. The unit will start to read the media and to start the playback
automatically.
4. ID3 function can be enable/disable in the "MENU" function.
USB connector does not support connection with USB extension cable and it is not designed for communication
with computer directly.
PROGRAMMED USB OPERATION
Program mode works in Stop mode
1. Hold the RANDOM / P - / PROGRAM / MEMORY button for 2 seconds. Then, the "00000P:01" will be shown on the
display and the first 2 digits will be flashing.
2. Press TUNE + / NEXT or TUNE - / BACK button to select the desired folder. After press RANDOM / P - / PROGRAM
/ MEMORY button to confirm the folder, the 3rd to 5th digits will be flashing.
3. Press TUNE + / NEXT or TUNE - / BACK button to select the desired track. Then, press
RANDOM / P - / PROGRAM / MEMORY button to confirm the track number.
4. Press RANDOM / P - / PROGRAM / MEMORY button again to confirm the setting. The
display will show next program number.
5. Repeat the sequence as indicated in 2 to 4 for next program.
6. After all the desired programs have been selected, Press ENTER/PLAY/PAUSE button for
playback.
MUTE ON/OFF
The mute on/ off is changed cyclically by pushing MUTE button.
The "mute" mark is on during mute is on.
The mute on is cancelled in case as shown below.
a. The power is off/on
b. The Volume is adjusted by the VOL +/- button.
PRESET EQ
1. Press MENU button until EQ shown on the display.
2. Press ENTER/PLAY/PAUSE button to enter E�� setting mode. ENTER/PLAY/PAUSE button to enter E�� setting mode.
3. Press MENU button to select of the EQ effect will be :
- FLAT -> ROCK -> JAZZ -> CLASSIC -> POP -> FLAT.
4. Press ENTER/PLAY/PAUSE button to confirm the setting. ENTER/PLAY/PAUSE button to confirm the setting.
5. Press STOP button to clear the E�� setting mode.

FOLDER SELECTION

1. In STOP mode, press BAND/FOLDER button will skip to the next folder.
2. This operation valid for all media of MP3 / WMA / USB operation.
SCR186-AMFM ENG-MP3-WMA-USB-LENC7 7
to enter E�� setting mode.
to confirm the setting.
button to clear the E�� setting mode. to clear the E�� setting mode.
E 5
MP3/WMA/USB display
USB display
7/7/2006 5:53:12 PM