Grizzly G0441 Instruction Manual
1.5 hp, 2 hp, 3 hp cyclone dust collectors
Hide thumbs
Also See for G0441:
- Machine data sheet (2 pages) ,
- Parts breakdown (2 pages) ,
- Instruction manual (65 pages)
Advertisement
Quick Links
Download this manual
See also:
Owner's Manual
Improvements to this machine were made since the manual was originally printed, and this update covers
those changes. Keep this update with your Owner's Manual in case you ever need to refer to it. If you have
questions, contact Tech Support at (570) 546-9663 or by email at techsupport@grizzly.com.
Larger Impeller & Blower
We increased the size of the impeller from 15"
to 15
⁄
" for improved performance. We also
1
2
increased the size of the blower to accomodate
the new impeller.
The new part number for the 15
P0441014A. The new part number for the blower
is P0441018A.
Improved Magnetic Switch
We improved the remote controlled magnetic
switch since the manual was originally printed.
The new switch features an overload device that
requires the cyclone to be restarted after it has
been overloaded. The new features of the switch
are described below:
POWER: Lights up when there is power to the
machine.
RUN: Lights up when the machine is running.
OVER: Lights up if the machine has been over-
loaded. Machine will not start again until it has
been reset at the main switch.
To reset the machine from the overload state, turn
the main switch OFF, then ON.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
⁄
" impeller is
1
2
COPYRIGHT © FEBRUARY, 2006 BY GRIZZLY INDUSTRIAL, INC.
#TR8039 PRINTED IN TAIWAN
MODEL G0441
3 HP CYCLONE
MANUAL UPDATE
���
���
��������
��
�
�
�
�
���
���������
REMOTE CONTROL
SWITCH
2H
OVER
MAIN
SWITCH
��������
���������
ON/OFF
8H
4H
RUN POWER
TIMER
220 VOLT
Advertisement
Related Manuals for Grizzly G0441
Summary of Contents for Grizzly G0441
- Page 1 Improvements to this machine were made since the manual was originally printed, and this update covers those changes. Keep this update with your Owner's Manual in case you ever need to refer to it. If you have questions, contact Tech Support at (570) 546-9663 or by email at techsupport@grizzly.com. Larger Impeller & Blower ���...
- Page 2 G0441 New Switch and Wiring Diagram ������������ ����� ������������ �� �� ��� ��� ��� ���� �� ��� ��� ��� ���� ��� �� � � � ������� �� �� �� �� ��� �� �� ��� �� �� �� �� ����� G0441 3HP CYCLONE DUST COLLECTOR...
- Page 3 Filter Support Brace Gaskets ..... 2 COPYRIGHT © OCTOBER, 2005 BY GRIZZLY INDUSTRIAL, INC. WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC. #TR7649 PRINTED IN TAIWAN...
- Page 4 Use a razor or putty knife to cut the silicone Separate the intake port from the black box, around the filter intake port. and completely clean off all remaining sili- cone. Cut the silicone around the black box. Pull or cut off the existing handle covers, loosen the screw above the handles, and remove the handles from the cable.
- Page 5 . Unfasten the screws at the bottom of the fil- Unfasten the bolt at the bottom of the filter. ter. Remove the original brush handle holder. . Remove the original brush. . Install the handle holder so it is directly below .
- Page 6 . Fasten the square pipe to the top of the fil- . Feed the new cable up through the brush, ter. over the pulley, and back down through the brush, making sure the brush screw is facing the pulley. 15. Insert the new brush and base on the square pipe.
- Page 7 . Feed the cable over the pulleys in the black . Secure the stop bead on the right side of the box. cable, approximately 12" from the end. . Pull the left side of the cable down until it . Fasten the black box to the top of the filter. stops, and secure the stop bead up against the handle holder.
- Page 8 . Fasten the screw on the handle, and install . Make sure that when the red handle is up the the other handle on the left side of the cable. filter brush is at the bottom of the filter. . Insert the covers on the handles so the red .
- Page 9 . Fasten the filter intake with the screws. 32. Use the two filter support gaskets between the filter support braces and the filter when reinstalling the filter on the cyclone. Filter Support Brace Gasket . Put silicone around the edges of the black box and filter intake to seal them to the filter.