DVD. Selects a programmed DVD player. VCR. Selects a programmed VCR. CBL. Selects a programmed cable TV set-top box. SAT. Selects a programmed satellite TV set-top box. AMP. Selects a programmed amplifier. CD. Selects a programmed CD player. AUX. Selects a programmed component. www.gateway.com...
Page 7
MUTE. Turns the sound on and off. 100. Enters channel numbers greater than 100. VOL. Turns volume up or down. INPUT. Changes the input source. LAST. Recalls the previously viewed channel. WIDE. Cycles through standard and widescreen viewing modes. CH. Changes the channel. www.gateway.com...
Page 8
Record. Records the CD, DVD, or VCR when the component is activated. Stop. Stops the CD, DVD, or VCR when the component is activated. Pause. Pauses the CD, DVD, or VCR when the component is activated. www.gateway.com...
Page 9
TV. Selects TV as the input source. VIDEO (AV1). Selects the component connected to AV1 (Video) as the input source. S-VIDEO (AV1). Selects the component connected to AV1 (S-Video) as the input source. AV2. Selects the component connected to AV2 as the input source. www.gateway.com...
Remote Control User’s Guide Inserting batteries To install batteries: ■ Insert two AA batteries into the remote control. Make sure that you match on the batteries with the symbols inside the battery – – compartment. www.gateway.com...
Programming the remote control Programming the remote control The TV component button has been preset to work with your Gateway plasma TV (program code 0077). You can program the remote control to work with as may as seven other components.
To clear the component button: Make sure that the component is turned on. Press and hold the button on the remote control until the LED SETUP flashes twice. Press , then press the component button on the remote control twice. 9 9 2 www.gateway.com...
LED flashes twice. SETUP Press . The LED flashes twice. 9 9 3 Press the component button that you want ( ) once. The LED flashes twice. Volume will now be controlled through the receiver for all components. www.gateway.com...
TV remote control making sure that the infrared ports are lined up, then press the button on the teaching remote control that you want the remote control to learn. The LED flashes twice. Press to exit learning mode. SETUP www.gateway.com...
MENU Press the utton again to select the menu that you want. MENU b Press the buttons to select the option you want to change. Press the buttons to change settings. Press the button to exit the OSD. EXIT www.gateway.com...
Your sleep timer is EXIT now running in the background. To turn off the sleep timer using the remote control: ■ Press the button repeatedly until appears. SLEEP Sleep Time: 0 Minutes www.gateway.com...
Use the number pad to enter your password when prompted. If you have not set a password, enter 1234. For more information about setting a password, see “Setting a password” on page 27. Enter the password using the number buttons on the remote **** Press Exit button to Cancel www.gateway.com...
Page 29
NC-17 (no one under 17 years of age) ■ X (no one under 17 years of age) ■ Press the buttons on the remote control to select Block Show then press when you have finished making your selections. Exit www.gateway.com...
Page 30
US TV Ratings button to open the sub-menu. You can customize the following ratings: TV-Y (all children) ■ TV-Y7 (older children) ■ TV-G (general audience) ■ TV-PG (guidance suggested) ■ TV-14 (strongly cautioned) ■ TV-MA (mature audience) ■ www.gateway.com...
Make sure that you pick a password that is easy to remember or store your password in a safe place. If you forget your password, you must call our Service Center at 888-737-MyGW (6949) to get information on how to reset your password. www.gateway.com...
Page 32
Setup menu. MENU Press the buttons to select the sub-menu, then press the V-Chip button to open the menu. Enter the password using the number buttons on the remote **** Press Exit button to Cancel www.gateway.com...
Page 33
Press the button to select , then press the button to exit the Save menu. The Password Has Changed menu opens. Press the button to select , then press the button to confirm the password change and exit the menu. www.gateway.com...
See “Programming the remote control” on page 7. ■ Make sure that you tried all the program codes listed for the component manufacturer. See “Component program codes” on page 8. ■ Perform the component code search procedure. See “Searching for component codes” on page 19. www.gateway.com...
Page 36
MAN MON DTV C48C REMOTE USER GDE R0 6/03...