Parts And Functions; Indoor Unit; Remote Controller; Display Board - Haier HSU-24LEA13-M - annexe 1 Operation Manual

Parts and Functions

Parts and Functions

Indoor Unit

Inlet
Inlet grille
Air Purifying Filter (inside)
Outlet
Actual inlet grille may vary from the one shown in the
manual according to the product purchased

Display board

Signal receiver hole
HEALTH display
(If the unit which you purchased
has healthy function,follow it.
If not,please ignore.)
TIMER OFF display
TIMER ON display
SLEEP display

Outdoor Unit

OUTLET
CONNECTING PIPING AND ELECTRICAL WIRING
DRAIN HOSE
INLET

Clock set

Press CLOCK button, "AM" or "PM" flashes.
Press or to set correct time. Each press
or decrease 1min. If the button is kept pressed,time will
change quickly. After time setting is confirmed,press SET,
"AM "and "PM" stop flashing,while clock starts working.
MODE SET
TIMER
FAN
CLOCK
SWING
1
Horizontal flap
(adjust up and down air flow
Don't adjust it manually)
Vertical blade
(adjust left and right air flow)
Anion generator
(inside)
Ambient temp.display
When receiving the remote control signal,
display the set temperature and in the rest
time the room temperature is displayed and
this room temperature is only for reference.
AUTO display
COOL display
Dry display
HEAT display
will increase

Remote controller

1
2
ON OFF
A o
AM
C
U
3 T
PM
O
4
5
ON/OFF TEMP
12
MODE SET
13
TIMER
FAN
14
15
CLOCK
SWING
16
SLEEP HEALTH
17
LOCK RESET
18
1. Operation mode display
ation mode AUT O COOLDRY HEAT
Ope
r
Remote controller
Display board
2. SWING display
3. FAN SPEED display
AUTO LO MED HI
4. HEALTH display
5. SLEEP display
6. LOCK display
NOTE:
Cooling only unit do not have displays and functions related with heating
If the unit which you purchased has healthy function,follow it.If not,please ignore.

Loading of the battery

resetting key(cylinder);
Load the battery,then put on the cover again.
Note:
The distance between the signal transmission head and the
receiver hole should be within 7m without any obstacle as well.
When electronic-started type fluorescent lamp or change-over
wireless telephone is installed in the type fluorescent lamp or
room, the receiver is apt to be disturbed in receivingthe signals,
so the distance to the indoor unit should be shorter.
Full display or unclear display during operation indicates the
batte ries have been used up. Please change batteries.
If the remote controller can't run normally during operation,
please remove the batteries and
Hint:
Remove the batteries in case unit won't be in usage for a long period.
If there are any display after taking-out, just need to press reset key
7. SIGNAL SENDING display
8. TIMER OFF display
9. TIMER ON display
6
10. CLOCK display
11. TEMP display
7
12. POWER ON/OFF
8
Used for unit start and stop.
9
13. MODE
10
Used to select AUTO run, COOL,
HEAT DRY and FAN operation
14. FAN
11
Used to select fan speed LO, MED,
HI, AUTO
19
(This function is unavailable on
some models.)
20
15. HOUR
Used to set clock and timer setting.
16. SWING
21
Used to set auto fan direction.
17. SLEEP
Used to select sleep mode.
(This function is unavailable on
22
some models.)
18. LOCK
Used to lock buttons and LCD display
19. TEMP.
24 Used to select your desired temp.
20. SET
23
Used to confirm timer and clock
settings.
21. TIMER
Used to select TIMER ON,
TIMER OFF, TIMER ON-OFF
FAN
22. CLOCK
Used to set correct time
23. RESET
Used to reset the controller back to
normal condition.
24. HEALTH
Used to operate the healthy function
Remove the battery cover;
Load the batteries as
illustrated. 2 R-03 batteries,
Be sure that the loading
is in line with the " + "/"-";
reload several minutes later.
.