Parts And Functions - Haier HSU-10TSV13-SC Operation Manual

Parts and Functions

Indoor Unit
Inlet
1 1
2 2
Inlet grille
3 3
Outlet
Anion generator
(
inside, only applicable for certain
7
Horizontal flap
(adjust up and down air flow
Don't adjust it manually
Display board
1
Signal receiver
emp.display
2
Actual inlet grille and Display board may vary from the one
shown in the manual according to the product purchased
Outdoor Unit
●
Loading of the battery
3
4
Load the battery,then put on the cover again.
Note:
The distance between the signal transmission head and the rece-
iver hole should be within 7m without any obstacle as well.
When electronic-started type fluorescent lamp or change- over
type fluorescent lamp or wireless telephone is installed in the
room, the receiver is apt to be disturbed in receiving the signals,
so the distance to the indoor unit should be shorter.
Full display or unclear display during operation indicates the
batteries have been used up Please change batteries.
If the remote controller can't run normally during operation, please
remove the batteries and reload several minutes later.
1
5 4 Air Purifying Filter
(inside)
Vertical blade
6
(adjust left and right air flow)
Display board
1
2
Operation mode indicator
3
OUTLET
INLET
CONNECTING PIPING
AND ELECTRICAL
4
WIRING DRAIN HOSE
1
Remove the battery cover;
2
Load the batteries as illustrated.
2 R-03 batteries, resetting key
(cylinder);
Be sure that the loading
is in line with th e" + "/"-";
Remote controller
1
2
3
4
8
Emergency
5
Switch
9
TURBO/QUIET
10
SELF
MODE
11
CLEAN
12
13
14
I FEEL SLEEP
15
TIMER
HEALTH
16
LOCK LIGHT
17
3
1. Mode display
Operation mode
Remote controller
2.Signal sending
3.display SWING
4.display FAN SPEED display
LO MED
5. LOCK display
6.TIMER OFF display
7.TIMER ON display
8.TEMP display Additional
functions display
Operation mode
QUIET SLEEP HEALTH
Remote controller
9.TURBO/QUIET button
10.SELF CLEAN button
11.MODE button
12.SWING UP/DOWN button
13.FAN SPEED button
14.I FEEL button
15.SLEEP button
16.LOCK button
17.LIGHT button
18.POWER ON/OFF button
19.ECO button
20.TEMP button
21.SWING LEFT/RIGHT button
(only applicable for certain models)
22.HEALTH AIR FLOW button
23.CONFIRM/CANCEL button
Function :Setting and cancel to the
timer and other additional functions.
24.TIMER button
25.HEALTH button
26.RESET button
When the remote controller appears
abnormal,use a sharp pointed
article to press this button to reset
the remote.
1
6
2
7
3
4
5
8
9
18
10
19
11
20
12
21
13
22
HEALTH 14
AIRFLOW
23
15
CONFIRM
CANCEL 24
25
16
R E S E T
26
17
1. Mode display
Operation mode
COOL DRY FAN
Remote controller
2.Signal sending
3.display SWING
4.display FAN SPEED display
circulated
LO
AUTO
HI
5. LOCK display
6.TIMER OFF display
7.TIMER ON display
8.TEMP display Additional
functions display
Operation mode
TURBO
Remote controller
9.TURBO/QUIET button
10.SELF CLEAN button
11.COOL button
12.SWING LEFT/RIGHT button
(only applicable for certain models)
13.FAN SPEED button
14.HEALTH button/DRY button
(Refer to the actual remote control layout
for specific functions)
15.SLEEP button
16.LOCK button
17.LIGHT button
18.POWER ON/OFF button
19.DRY button/ECO button
(Refer to the actual remote control layout
for specific functions)
20.TEMP button
21.SWING UP/DOWN button
22.TIME OFF/ON button
23.EXTRA FUNCTION button
Function :FAN---Healthy airflow position1---
Healthy airflow position2
Function :FAN --- Health
24.CONFIRM/CANCEL button
Function :Setting and cancel to the timer
and other additional functions.
25.RESET button
When the remote controller appears
abnormal,use a sharp pointed article to
press this button to reset the remote.
6
7
8
18
TURBO/QUIET
19
SELF
COOL
CLEAN
20
21
SWING
22
EXTRA
SLEEP
FUNCTION
23
TIME TIME CONFIRM
OFF CANCEL
ON
24
LOCK LIGHT R E S E T
25
COOL DRY
FAN
circulated
MED HI AUTO
QUIET SLEEP HEALTH TURBO