Fader Start Playback; Relay Play Using Two Players; Data Copy - Pioneer CMX-3000 Operating Instructions Manual

Applications (Advanced operations)
Remote control unit
PITCH BEND+,–
TRACK
SEARCH
(4,¢)
CUE
PLAY/
PAUSE
(3 8)
Jog dial
Press the BPM SYNC button.
¶ The BPM SYNC button will flash and the player enters the
BPM synchro playback mode.
¶ If both players are currently in playback mode, no
synchronization is possible until playback is stopped on one
of the players. When one player is stopped, the player still
playing back is considered the master.
¶ If start is begun when the BPM on the slave player is
unknown, synchro playback will begin at the point the slave's
BPM value is measured.
¶ During BPM synchro, the MASTER indicator will light on the
"master" player's display. On the slave player, the tempo
control range display will turn off and the tempo change rate
display will show the tempo compensation value.
¶ During BPM synchro, the slave player's tempo will change to
match any tempo changes on the master side. In this case,
the tempo and pitch bend of the slave player cannot be
independently adjusted.
¶ If playback is interrupted on the master player, the slave
player will become the master.
When this occurs, if the tempo control of the new master
player is at a different setting from the tempo of the currently
playing track, the display will alternately show the message
dEc (or Inc), and the amount of tempo deviation. To reduce
the tempo deviation to zero, move the tempo control slide to
the "–" side if dEc is displayed, and to the "+" side if Inc is
displayed. Speed control using the tempo control slide
becomes possible when the tempo has been adjusted.
7 Correcting beat timing
¶ When beat is detected during BPM synchro, the ring display
will light to graphically indicate the four-beat timing.
¶ The four-beat timing of the currently playing track on players
A, B can be designated by tapping the TAP button with that
timing once on each of the two players. The beat timing of
the slave player will be automatically brought into
correspondence with that of the master player, so as to
match the designated beat timing.
NOTES:
¶ It may not be possible to correctly measure the BPM value
for some tracks. If this happens, press the TAP button in time
with the beat to enable a more accurate BPM synchro
playback. However, if the BPM synchro range is outside the
adjustable range of the player, appropriate BPM synchro
playback may not be possible.
¶ During BPM synchro, the tempo control slide and pitch bend
operations are disabled on the slave player.

Fader Start Playback (*)

The provided control cable may be used to connect the control
jack on the CMX-3000 to a control jack on a DJM-300, DJM-500,
or DJM-600 mixer, thus making it possible to exit from cueing
standby mode and to start playback immediately by raising the
DJ mixer CHANNEL FADER. The CROSS FADER may also be
used to perform fading starts on the player as well. The fader
may also be returned to its original position to return the player
to the cueing point (i.e., to perform back cueing). (This does not
apply, however, during auto playback.) (See p. 10 for
instructions on how to connect the player and mixer.)
18
<DRB1307>
RELAY PLAY
MASTER
TEMPO
BPM SYNC
Tempo control slide

Relay Play Using Two Players (*)

÷ Set both player's auto cue function to ON (the A. CUE
indicators will light in the displays).
÷ Set your DJ mixer's fader control to its center position.
1. Press the RELAY PLAY button to blink the button
indicator.
2. Begin playback on the first player.
3. When the currently playing track ends, playback
will begin automatically on the standby player.
4. The first player will enter cue standby mode at the
beginning of the next track on its disc.
¶ By repeating this operation, the two players can be used
to perform continuous relay play.
¶ By loading new discs on the standby player, you can
construct a continuous program of whatever tracks you
wish.
¶ By setting a Cue point on the standby player, you can
perform relay to any desired Cue point on the selected
track (see page 13: Cueing Point Settings).
NOTES:
÷ Fader start and relay play cannot be performed simultane-
ously.
÷ When the Auto Cue function is off, replay will be performed
of the entire disc.

Data Copy

WAVE and other data recorded in this unit can be copied to
another CMX-3000 if desired.
1. With the unit power off, use a control cord to
connect the two player's DATA IN/OUT connec-
tors.
2. On each CMX-3000, turn on power while simulta-
neously pressing the EJECT buttons on players A
and B. (The remote control unit's EJECT button
cannot be used for this operation.)
÷ The power will turn on, and data copy mode (slave mode)
will be established; the display will show "SLAVE M".
3. With both units in the data copy mode ("slave
mode"), press the CD TEXT/WAVE button on the
player A holding the WAVE data you wish to copy.
Hold the button depressed for one second.
÷ This unit will enter the master mode and the display will
show "MASTER."
4. Press the PLAY/PAUSE button (38) of Player A on
the "master" unit.
÷ Data copying will begin, and the 38 indictor will flash.
÷ About ten minutes will be required for the copy operation.
END is displayed on the master when copying is
completed.
5. Turn off the power on both units and disconnect
the control cord.
÷ When power is turned on again, operation will return to
normal mode.
NOTES:
÷ Do not turn off the power or disconnect cables during
copying to prevent corruption of the copying data.
÷ If the ERROR message is displayed during data copy, check
your connections and perform the data copy function again.