Table of Contents
Advertisement
Available languages
Available languages
1 Warnings
General Safety
•
Never place your machine on a carpet
covered floor. Otherwise, lack of airflow from
below of your machine may cause electrical
parts to overheat. This may cause problems
with your washing machine.
•
If the power cable or mains plug is damaged
you must call Authorized Service for repair.
•
Fit the drain hose into the discharge housing
securely to prevent any water leakage and
to allow machine to take in and discharge
water as required. It is very important that the
water intake and drain hoses are not folded,
squeezed, or broken when the appliance
is pushed into place after it is installed or
cleaned.
•
Your washing machine is designed to
continue operating when the power restores
after a power interruption. The machine will
resume its program when the power restores.
Press the "Start/Pause/Cancel" button for
3 seconds to cancel the program (See,
Canceling a Program)
• There may be some water in your machine
when you receive it. This is from the quality
control process and is normal. It is not harmful
to your machine.
•
Some problems you may encounter may be
caused by the infrastructure. Press "Start/
Pause/Cancel" button for 3 seconds to cancel
the program set in your machine before calling
the authorized service.
First Use
• Carry out your first washing process without
loading your machine and with detergent
under "Cottons 90°C" program.
•
Ensure that the cold and hot water
connections are made correctly when
installing your machine.
•
If the current fuse or circuit breaker is less
than 16 Amperes, please have a qualified
electrician install a 16 Ampere fuse or circuit
breaker.
•
While using with or without a transformer, do
not neglect to have the grounding installation
laid by a qualified electrician. Our company
shall not be liable for any damages that may
arise when the machine is used on a line
without grounding.
•
Keep the packaging materials out of reach
of children or dispose them by classifying
according to waste directives.
Intended use
•
This product has been designed for home
use.
• The appliance may only be used for washing
and rinsing of textiles that are marked
accordingly.
• This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities,
or lack of experience and knowledge,
unless they have been given supervision or
instruction concerning use of the appliance by
a person responsible for their safety.
Safety instructions
• This appliance must be connected to an
earthed outlet protected by a fuse of suitable
capacity.
• The supply and draining hoses must always
be securely fastened and remain in an
undamaged state.
•
Fit the draining hose to a washbasin or
bathtub securely before starting up your
machine. There may be a risk of being
scalded due to high washing temperatures!
•
Never open the loading door or remove the
filter while there is still water in the drum.
• Unplug the machine when it is not in use.
•
Never wash down the appliance with a water
hose! There is the risk of electric shock!
• Never touch the plug with wet hands. Do not
operate the machine if the power cord or plug
is damaged.
• For malfunctions that cannot be solved by
information in the operating manual:
•
Turn off the machine, unplug it, turn off
the water tap and contact an authorized
service agent. You may refer to your local
agent or solid waste collection center in your
municipality to learn how to dispose of your
machine.
If there are children in your house...
• Keep children away from the machine when it
is operating. Do not let them tamper with the
machine.
• Close the loading door when you leave the
area where the machine is located.
2 Installation
Removing packaging reinforcement
Tilt the machine to remove the packaging
reinforcement. Remove the packaging
reinforcement by pulling the ribbon.
Opening the transportation locks
Transportation safety bolts must be removed
A
before operating the washing machine!
Otherwise, the machine will be damaged!
1. Loosen all the bolts with a spanner until they
rotate freely ("C")
2. Remove transportation safety bolts by turning
them gently.
3. Fit the covers (supplied in the bag with the
Operation Manual) into the holes on the rear
panel. ("P")
2 - EN
Advertisement
Table of Contents
