Parts And Functions; Remote Controller; Indoor Unit; Outdoor Unit - Haier HSU-09HVd03 Operation Manual

Parts and Functions

Indoor Unit

Inlet
Inlet grille
Air purifying
Filter(inside)
Anion generator
(inside)
Horizontal flap
(adjust up and down air flow
Don't adjust it manually)
Please be subject to the actual produce purchased the
above picture is just from your reference
Display board
Singal receiver hole
AUTO display
COOL display
Dry display
Ambient temp.display
When receiving the remote control signal,
display the set temperature and in the rest
time the room temperature is displayed and
this room temperature is only for reference.

Outdoor Unit

OUTLET
INLET
Please be subject to the actual produce purchased the
above picture is just from your reference

Clock set

Press CLOCK button, "AM" or "PM" flashes.
Press or to set correct time. Each press
or decrease 1min. If the button is kept pressed,time will
change quickly. After time setting is confirmed,press SET,
"AM "and "PM" stop flashing,while clock starts working.
2
Vertical blade
(adjust left and
right air flow)
Display board
TIMER OFF display
TIMER ON display
SLEEP display
HEAT display
HEALTH display
(If the unit which you purchased
has healthy function,follow it.
If not,please ignore.)
FRESH AIR display
CONNECTING PIPING
AND ELECTRICAL WIRING
DRAIN HOSE
will increase
STERILIZE

Remote controller

Outlet
1.CODE
Used to select CODE A or B with a press,
A or B will be displayed on LCD.
Please select A without special explanation.
2.RESET
When the remote controller appears
abnormal, use a sharp pointed article to
press this button to reset the remote
controller normal.
3.LIGHT button
Control the lightening and extinguishing of
the indoor LED display board.
4. TIMER button
5. CLOCK button
6. SLEEP button
7. MODE button
8. HOUR button
9. HEALTH button
NOTE : The following functions and related displays are not available: 1

Loading of the battery

4
Load the battery,then put on the cover again.
Note:
The distance between the signal transmission head and the rece-
iver hole should be within 7m without any obstacle as well.
When electronic-sta rted type fluorescent lamp or change- over
type fluorescent lamp or
room, the recei ver is apt to be disturbed in receiving the signals,
so the distance to the indoor unit should be shorter.
Full display or unclear display during operation indicates the
batte ries have been used up. Please change batteries.
If the remote controller can't run normally during operation, please
remove the batteries and
Hint:
Remove the batteries in case unit won't be in usage for a long period .
If there are any display after taking-out, just need to press reset key.
19
10. ON/OFF button
11. TIMER ON display
12. FAN SPEED display
LOW MED
13. LOCK display
14. SWING UP/DOWN display
15. SLEEP display
16. HEALTH display
17.FRESH AIR display
18. Operation mode display
28
Operation mode
FRESH
Remote con troll er
Display board
STERILIZE
19.Singal sending display
20. UV light degerming function display
33
21. Left/right air flow display
22. TEMP display
23. TIMER OFF display
24. TIMER/SLEEP display
25. TEMP button
26. FAN button
27. HEALTH AIRFLOW button
28. SWING UP/DOWN button
29. SWING LEFT/RIGHT button
30. FRESH button
31. SET button
32. STERILIZE button
33. LOCK
Used to lock buttons and LCD display.If
pressed,the other buttons will be disabled
and the lock condition display appears.
Press it once again,lock will be canceled
and lock condition display disappears.
34. Ambient temp.display
When receiving the remote control signal,
display the set temperatrue and in the rest
time the room temperature is displayed and
this room temperature is only for reference.
1
Remove the battery cover;
2
Load the batteries as illustrated.
2 R-03 batteries, resetting key
(cylinder);
3
Be sure that the loading
is in line with the
wireless telephone is installed in the
reload several minutes later.
HI AUTO
AUTO COOL DRY HEAT FAN
" + "/"-";