Table of Contents
Advertisement
Available languages
Available languages
Roc740_GB
25/04/01 16:05
Setting date and time
1. Press the
key (
SET UP
2. Release the
key.
SET UP
3. Press once again on the
The day display will blink.
4. Press the
key (
19
FFWD
"Mo" for Monday, "Tu" for Tuesday, "We" for Wednesday, "Th" for Thursday,
"Fr" for Friday, "Sa" for Saturday and "Su" for Sunday.
5. Press briefly on
(
OK
22
6. Choose the correct hour using the
then briefly press
OK
7. Choose the correct minute using the
then briefly press
OK
8. Setting is now finished: the display will now show the day, hour and minute settings you chose.
Storage of listed codes in memory
The code list for various current household items you can control is delivered separately from the
the one or more codes that you can use for controlling the equipment you want. Then utilize the following procedure:
1. Keep the
(
) key pressed until "Setup" displays on the LCD panel.
17
SET UP
2. Release the
key.
SET UP
3. Press briefly on that key for the mode you want (
For
mode press briefly on the
AUX
mode key (
,
,
TV
VCR
SAT
4. Enter the first code listed for the concerned equipment item.
(For example
for a Thomson TV set).
016
If the code is incorrect "Invalid" will display for a few seconds.
Check the code you used from the code list and try again from Step 4.
5. When you have the right code the day and time will display, confirming your choice.
6. Entry of the equipment item code is now finished.
Note: When the list shows several equipment item codes for the same manufacturer this indicates that some codes in the list cover more
equipment control functions than other codes listed (this also depends on the year the concerned item was first sold). In such case and
after having entered a code, try to remote operate your equipment using the various function keys of your
you to find out which functions can be controlled using a particular code. If you cannot operate all available functions, enter another
code from the list. Where you do not find any utilizable code under the equipment manufacturer's name you will have to make a code
search (see following paragraph), or load the right codes for each function from the original remote controller for your equipment
item using the learning function (page 5).
Code search
If you were not able to find the right code for your equipment item in the separately available code list you can make a search for it,
proceeding as follows:
1. Turn on the equipment item you want to remote control using the front panel controls (On/Off switch or Standby switch).
2. Press the
(
) key until "Setup" displays.
SET UP
17
3. Release the
key.
SET UP
4. Press
briefly for the mode you require (
SET UP
For the
, mode briefly press either of the
AUX
you want (
,
,
TV
VCR
SAT
5. Press several times on the
control reacts, eg. by changing the channel selection. The display will show "Search"
as well as the mode and the code you are trying out. Do not proceed too fast between each
code you test to allow the equipment time for data interchange. If you went too fast and want
to return you can use the
6. Press briefly on the
OK
It may be useful to note the right code for later use.
When you change the batteries it may be necessary to reprogram the remote control.
7. Code search is now finished. The LCD panel will indicate the day and time.
Note: if the original item's remote control does not have a key with a function similar to the
scrolling, you can make code search by using the
Code search will start with the last-stored code for the mode currently selected, for example if that mode has 100 codes and the stored
code is 050 code search will start at 051 and range to 100, then restart from 000 through 050. This will ease your code selection task
where several codes apply to your equipment item, by skipping any codes already tested.
After code search and when you manually select the code you must be sure you selected the right code, that one or ones giving control
of all equipment item functions. Where you find that certain functions are still not able to be remote controlled because no code allows
you to reproduce all capacities of the item's original remote control, your
mode.
Programming control for a COMBO (combined TV/VCR)
Programming the remote control for a COMBO breaks down to programming it once as a TV, and a second time as a VCR, these being
the two main functions of a COMBO.
Before starting to program, find the right codes for the TV and the VCR functions of your COMBO, then follow the procedure in "S
of listed codes in memory
Page 3
) until "Setup" displays on the LCD panel.
17
key. "Time" will display on the LCD panel.
SET UP
) to advance, or the
(
) to go back until the correct day displays:
5
REV
) to validate. The hours display will now blink.
(
) or
(
FFWD
19
REV
5
(
) to validate. The minutes display will now blink.
22
(
) or
FFWD
19
REV
(
) to validate.
22
,
TV
VCR
or
keys, then on the desired
AUX 1
AUX 2
, etc...).
,
,
TV
VCR
or
AUX 1
, etc...).
+ key (
) until the equipment item you wan to
10
PROG
key (
) to move back to a previous setting.
REV
5
key to store the equipment item code you select.
key for a VCR or the
PLAY
" in the previous paragraph.
) keys to obtain the right hour,
(
) keys to obtain the right minute,
5
,
, etc...).
SAT
, etc...).
SAT
keys then that for the mode
AUX 2
key (
) .
1
ON
can load the missing functions through its learning
ROC 740
3
Setup
Mode ?
Time
Fr
12:48
. Read the code list to obtain
ROC 740
Setup
Mode ?
Setup
TV
016
. This will enable
ROC 740
Setup
Mode ?
Search
TV
016
key for 'zapping' or rapid channel
PROG
torage
Hide quick links:
Advertisement
Table of Contents
