Advertisement
XL-V211BK
|
TROUBLESHOOTING
SPECIFICATIONS
System
: Compact disc player
Signal detection
: Non-contact optical
What appears to be a malfunction
may
system
system
not always be serious.
Number of channels: 2 channels
Make sure first..
Frequency response:
2 Hz—20,000 Hz
Although the disc is inserted in the CD
Dynamic range
: 96 dB (1 kHz)
player, MULT!
MODE
DISPLAY
shows
no
Signal/noise ratio
: 100 dB (at digital 0)
data.
Channel separation
- 90 dB (1 kHz)
ig the disc placed upside down?
Harmonic distortion
. 0.004%
(1 kHz)
—
Ptace the disc on the disc tray with its label
Wow
and flutter
: Less than measurable
side up.
limit
Selections cannot be programmed.
Output level
: 2.0 Vrms (full scale)
Is the "PROGRAM"
indicator lit?
Number of program : 32 steps
—
Press the [PROGRAM]
button.
steps
The remote control unit does not
Dimensions
> 435(W)
x 92(H) x 289(D)
function.
mm
Are the batteries fresh?
(17-3/16" x 3-5/8" x
—
Replace the batteries with new ones.
11-7/16")
.
The sound is intermittent and is harsh to
Weight
: 3.5 kg (7.9 Ibs)
the ear.
+ Accessories
: Signal cord
Is the disc dirty?
(1m
« 3.28 ft). .... 1
—
Wipe off the disc surface with a soft cloth.
Remote
cabie
is the disc scratched?
(1m
« 3.28 ft)
1
—
Replace the disc with a new one.
For XL-V311BK
Is the disc warped?
Remote control unit
—
Replace the disc with a new one.
(RM-SX311U).....
«1
Battery
(AA, R6, UM-3)
....2
Design
and specifications
subject to change
without notice.
POWER
SPECIFICATIONS
COTTE
Continental Europe
AC 220 Vv, 50 Hz
AC 240 V~, 50 Hz
AC 110-127/220-240 V selectable, 50/60 Hz
1-4 (No. 20083)
BEFORE USE
Set the voltage selector to your local line voltage.
(Fig. 6)
When this equipment is used in an area where
the supply voltage is different from the preset
voltage. reset the voltage selector to the correct
position.
(Not provided on units for U.S.A., Canada, Aus-
tralia, U.K. and Continental Europe.)
CHECKING
YOUR
LINE VOLTAGE
(Except
for U.S.A., Canada, Australia, U.K. and
Continental Europe.)
Betore inserting the power plug, please check
this setting to see that it corresponds with the
line voltage in your area. If it doesn't be sure to
adjust the voltage selector switch to the proper
setting before operating this equipment. The vol-
tage selector switch is located on the rear panel.
CAUTION:
©
Before setting the 'Voltage selector switch"
to proper voltage disconnect the power plug.
cComry une-)
ied
<—
CONNECTION
DIAGRAM
1. To the input terminal (CD, AUX or TAPE
PLAY) of an amplifier. (Do not connect to the
PHONO
terminals of the amplifier.)
2. To the "COMPU
LINK-1/SYNCHRO"
termi-
nai of an amplifier or a cassette deck when
you are using the COMPU-LINK
system.
Regarding compatible amplifiers or cassette
decks consult your dealer.
Either one of these two COMPU
LINK-1/SYN-
CHRO
terminals can be used.
3. To the wall outiet.
Notes:
@
When connecting any component to this
unit first set the [POWER] button to off.
@ Connect the audio plugs firmly.
~
@ The
synchronized
recording
is only
possible with JVC products which have
the COMPU LINK-1/SYNCHRO terminals.
For
further
details,
consult
your
JVC
dealer.
| XL-V211BK
COMPU LINK CONTROL
SYSTEM
This is a convenient system which was originat-
ed and developed by JVC. The following is a brief
explanation of its major points.
Automatic Source Selection
When the provided remote cables are used for
connecting this unit to other components which
have COMPU
LINK-1/SYNCHRO
terminals, the
switch-over of all system components is possible
with simple one-touch
of the source
selector
putton of the JVC amplifier or receiver. By doing
this, the corresponding
component
will start
playing automatically. The source select button
of the remote control unit or the select button
of the desired component can also be used for
this purpose.
When the components have been switched over,
the previously used component will stop playing
within five seconds.
Synchronized Recording
Synchronized recording refers to the process in
which
the cassette
deck
starts
recording
in
synchronism with the CD player. Perform
the
synchronized recording as follows.
1. Set the cassette deck to the REC/PAUSE
mode in accordance with the procedures in
the instructions.
2. If you want programmed recordings, program
the desired selections in any order you wish
to hear them.
3. Press the [PLAY ( ® )] button of the CD
player. By so doing, the cassette deck is
placed in the record mode and synchronized
with
the
CD
player
for
recording.
Synchronized
recording thus can be made
possible.
Notes:
@ Synchronized recording stops automati-
cally when the CD player stops playing.
@ To cancel synchronized recording, press
the [STOP(
@ )] button of the CD player
or cassette deck.
@ During
synchronized
recording,
the
operation of the [PLAY ( » )] button is
interlocked with the cassette deck.
@ When the REC/PAUSE
mode is set by
pressing
[PAUSE
( §f§ )} button
after
pressing
the
[REC
( © )} and
[PLAY
( » )}
buttons
simultaneously,
synchronized recording is not possible.
For details, refer to the instructions of the
cassette deck.
e@ Abnormal
operation
will result if the
power
supply of the component(s)
is
interrupted.
If this happens,
press
the
select buiton again to restart.
e Ensure
that
the
COMPU
LINK-1/
SYNCHRO
terminals
of the individual
components
are
connected
with
the
provided remote cables. Also be sure to
fully read
the
instructions
for each
component.
(No. 20083) 1-5
Advertisement
