Control Lock - KitchenAid KEBC177 Use & Care Manual

Tones a reaudible s ignals, indicating thefollowing:
Onetone
• Valid padpress
• Oven ispreheated
• Function hasbeen entered
Three tones
• Invalid pad press
Four tones
• End of cycle
• Reminder, repeating each minute after the end-of-cycle tones
Tone Volume
The volume is preset at high, but can be changed to low.
To Change: Press and hold the number pad 7 for 5 seconds. On
some models, a tone will sound and "Snd Lo" will appear on the
oven display for 3 seconds. If "Snd Lo" remains on the display,
press CANCEL to remove. Repeat to change back to "Snd HI."
All Tones (double oven models)
All of the above tones are preset on, but can be turned off.
To Turn Off/On: Press and hold STOP TIME for 5 seconds. On
some models, a tone will sound and "Snd Lo" will appear on the
oven display for 3 seconds. If "Snd Lo" remains on the display,
press CANCEL to clear. Repeat to change back to "Snd HI."
Pad Press Tones (single oven models)
The single tones signaling a valid pad press are preset on, but
can be turned off.
To Turn Off/On: Press and hold STOP TIME for 5 seconds. On
some models, a tone will sound and "Snd off" will appear on the
oven display for 3 seconds. If "Snd off" remains on the display,
press CANCEL to clear. Repeat to change back to "Snd on."
End-of-Cycle and Reminder Tones
The Timer and Timed Cooking end-of-cycle and reminder tones
are preset on, but can be turned off. On some models, if all tones
have been turned off, the end-of-cycle and reminder tones
cannot be independently turned on.
To Turn Tones Off/On: Depending on your model, press and
hold COOK TIME until a tone sounds and the oven display
returns to inactive mode (blank). If "EOC OFF" appears on your
display, press CANCEL to clear. Repeat to turn back on.
Reminder Tones Only
The Minute Timer and Timed Cooking reminder tones are preset
on, but can be turned off. However, on double oven models, if all
tones have been turned off, the reminder tones cannot be
independently turned on.
To Turn Tones Off/On: Press and hold TIMER SET/START until a
tone sounds. On some models, the oven display will display
"NA9 OFF." To remove this from the display, press CANCEL.
Repeat to turn back on.
The temperature is preset in Fahrenheit, however it can be
changed to Celsius.
To Change: Press and hold BROIL/MAXl//ECONO for 5 seconds.
Depending on your model, a tone will sound and "C °'' or "C" will
appear on the display for 3 seconds, or until you press CANCEL.
Repeat to change back to Fahrenheit.
When in Fahrenheit, "°F" follows the oven temperature.
When in Celsius, only ..... follows the oven temperature.
The Timer can be set in minutes and seconds or hours and
minutes and counts down the set time. It does not start or stop
the oven.
To Set:
1. Press TIMER SET/START,
Press again to switch between MIN/SEC and HR/MIN.
If no action is taken within a certain amount of time (between
1 minute and 4 minutes depending on your model), the
display will return to the time of day mode.
2=
3.
Press the number pads to set the length of time.
Press TIMER SET/START or START.
If not pressed within a certain amount of time (between
5 seconds and 4 minutes depending on your model), the
display will return to the time of day mode and the
programmed function will be canceled.
When the set time ends, if enabled, end-of-cycle tones will
sound, then reminder tones will sound every minute.
Press TIMER CANCEL anytime to cancel the Timer or stop
the reminder tones.
Remember, if a Cancel Off pad is pressed, the respective
oven will turn off.
The time can be reset during countdown by repeating the
above steps.
The Control Lock shuts down the control panel pads to prevent
unintended use of the oven(s). The Control Lock will remain set
after a power failure, if set before the power failure. The only time
it is not available is during the Sabbath Mode or Self-Clean cycle.
When the control is locked, the TIMER SET/START, TIMER
CANCEL, OVEN LIGHT and CANCEL OFF, UPPER OVEN
CANCEL/OFF or LOWER OVEN CANCEL!OFF pads will function.
On double oven models, CLOCK SET*START will also function.
The Control Lock is preset unlocked, but can be locked.
To Lock/Unlock Control: Press and hold the number pad 3
CONTROL LOCK for about 5 seconds until "CONTROL LOCK"
and a picture of a lock appear on the display. Repeat to unlock
and remove "CONTROL LOCK" from the display.